AmericanLongRifles Forums
General discussion => Contemporary Accoutrements => Topic started by: Tim Crosby on June 14, 2019, 11:13:54 PM
-
Made these up for one of the members here, first he's seen them, hope they'll work. The horn is about 6" long the butt is Maple, about 1 1/2", hollowed out about 3/4s its length, held in place by 4 Iron pins. The Two bands are also held in place by 3 as is the Pewter tip. As you can see it is relatively straight. It will hold just a bit over 10 65gr shots, could be used as a pocket/primer horn, especially for a small cal. gun.
The Measure was turned from Cow horn, Iron eye for strap, it holds just over 65grs.
Tim C.
(https://i.ibb.co/WcF0yk8/003.jpg) (https://ibb.co/kh0J84b)
(https://i.ibb.co/Rpd5VpQ/005.jpg) (https://ibb.co/fYLcPYr)
-
Nice.
Bob
-
Beautiful work as usual Tim. Love the pewter tip.
-
Oh that is one sweet pair Tim. That horn makes me smile, in a really good way. A tiny banded horn. Too cool.
That horn measure is neat too. It almost looks ebony with that color.
God Bless, Marc
-
That is a beautiful set. Would go great with a horn I have been playing around with.
Thanks for sharing, it's owner should be very happy with it.
Mike
-
Nice!
-
Thanks, the small band had to be made up, the Two on the Right were the candidates. The one on the left started out like the Two of them.
Tim
(https://i.ibb.co/Kzc9Syk/003.jpg) (https://ibb.co/YT4twjM)
-
As always, absolutely exquisite work!
-
I like it! Great work.
-
Thanks, the small band had to be made up, the Two on the Right were the candidates. The one on the left started out like the Two of them.
Tim
(https://i.ibb.co/Kzc9Syk/003.jpg) (https://ibb.co/YT4twjM)
How did you taper the hole, if you did?
-
That horn would be the epitome of perfection for a pistol. I'm not sure if I could effectively prime my pistol with it, but if so, it would be ideal for the woodswalks I shoot.
-
Thanks, the small band had to be made up, the Two on the Right were the candidates. The one on the left started out like the Two of them.
Tim
(https://i.ibb.co/Kzc9Syk/003.jpg) (https://ibb.co/YT4twjM)
How did you taper the hole, if you did?
Just getting back on. I rough turned the out side on a Pen mandrel, that's what the 1/4" hole is for. Then chucked it up, drilled a 3/4" hole in it and turned the center out. It is easy to get the taper. If I get a chance tomorrow I will post a couple of Pix if the process and the tool.
Tim
-
Great looking stuff there.
-
Good looking work Tim. I like the pewter ends you put on the horns.
-
Mark,
Here are a couple of Pix of the setup and a couple of the tool.
Tim
(https://i.ibb.co/8js7pvq/001.jpg) (https://ibb.co/P5j6nXK)
(https://i.ibb.co/6mdJt7k/002.jpg) (https://ibb.co/47QgSnH)
(https://i.ibb.co/YjC1QLP/003.jpg) (https://ibb.co/gg2f9Rm)
(https://i.ibb.co/gdFQ7Rs/004.jpg) (https://ibb.co/0KV1XGP)
(https://i.ibb.co/KX3HR5Y/005.jpg) (https://ibb.co/PNf83rR)
-
Thanks for the pictures.