« previous next »
Pages: [1]   Go Down

Author Topic: Tradegun Sight  (Read 6053 times)

Offline Pete G.

  • Hero Member
  • *****
  • Posts: 2013
Tradegun Sight
« on: October 10, 2012, 12:57:40 AM »
Aside from a couple of murky photos in the Hamilton book, has anyone seen a good picture of what the rear sight on a tradegun would look like? Was there a somewhat standardized sight or were they pretty much an individual thing ?
Logged

Offline Mike Brooks

  • Hero Member
  • *****
  • Posts: 13415
    • Mike Brooks Gunmaker
Re: Tradegun Sight
« Reply #1 on: October 10, 2012, 01:30:22 AM »
The one I use on my Carolina guns are cast from an original.
Logged
NEW WEBSITE! www.mikebrooksflintlocks.com
Say, any of you boys smithies? Or, if not smithies per se, were you otherwise trained in the metallurgic arts before straitened circumstances forced you into a life of aimless wanderin'?

Offline Dave B

  • Hero Member
  • *****
  • Posts: 3132
Re: Tradegun Sight
« Reply #2 on: October 10, 2012, 04:03:42 AM »
I am not sure who's piece this is but I loved the sight on this fowler. Maybe one of Mike's. I tucked it way in my collection of sight  photos when I came across it.
Logged
Dave Blaisdell

Offline Curtis

  • Hero Member
  • *****
  • Posts: 2338
  • Missouri
Re: Tradegun Sight
« Reply #3 on: October 10, 2012, 06:09:36 AM »
This trade gun sight is from a casting by Jack Brooks made from from an original type G:







This is the same type of sight shown on some of the "Type G" barrels in Hamilton's book.   Hope the pics help.

Curtis
Logged
Curtis Allinson
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Sometimes, late at night when I am alone in the inner sanctum of my workshop and no one else can see, I sand things using only my fingers for backing

Vomitus

  • Guest
Re: Tradegun Sight
« Reply #4 on: October 10, 2012, 08:06:22 AM »
Quote from: Dave B on October 10, 2012, 04:03:42 AM
I am not sure who's piece this is but I loved the sight on this fowler. Maybe one of Mike's. I tucked it way in my collection of sight  photos when I came across it.


  The late David Dodds? I'm guessing, but the touchmark looks familiar.
Logged

Offline Dennis Glazener

  • Administrator
  • Hero Member
  • *
  • Posts: 19483
    • GillespieRifles
Re: Tradegun Sight
« Reply #5 on: October 10, 2012, 06:54:59 PM »
Who sells these sights? I made a similiar one for my 16 bore fowler and really liked it for wing shooting. Would prefer to buy one than the make one for the fowler I will be building as soon as I get the barrel.
Dennis
Logged
"I never considered a difference of opinion in politics, in religion, in philosophy, as cause for withdrawing from a friend" - Thomas Jefferson

Offline rich pierce

  • Administrator
  • Hero Member
  • *
  • Posts: 19522
Re: Tradegun Sight
« Reply #6 on: October 10, 2012, 07:29:24 PM »
Quote from: Leatherbelly on October 10, 2012, 08:06:22 AM
Quote from: Dave B on October 10, 2012, 04:03:42 AM
I am not sure who's piece this is but I loved the sight on this fowler. Maybe one of Mike's. I tucked it way in my collection of sight  photos when I came across it.


  The late David Dodds? I'm guessing, but the touchmark looks familiar.

If memory serves, that picture is from an auction site, and it's a very early Dutch rifle.
Logged
Andover, Vermont

Offline Curtis

  • Hero Member
  • *****
  • Posts: 2338
  • Missouri
Re: Tradegun Sight
« Reply #7 on: October 10, 2012, 07:38:35 PM »
Dennis,

Jack Brooks may still have some castings of these available.  Here is his contact information:

Jack Brooks
800 West Oxford Ave.
Englewood, CO 80110
303-789-4029

jsbrookslongrifles@gmail.com

jsbrookslongrifles.com

Logged
Curtis Allinson
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Sometimes, late at night when I am alone in the inner sanctum of my workshop and no one else can see, I sand things using only my fingers for backing

Offline Dennis Glazener

  • Administrator
  • Hero Member
  • *
  • Posts: 19483
    • GillespieRifles
Re: Tradegun Sight
« Reply #8 on: October 10, 2012, 10:31:55 PM »
Thanks, sent him an email.
Dennis
Logged
"I never considered a difference of opinion in politics, in religion, in philosophy, as cause for withdrawing from a friend" - Thomas Jefferson

Offline Pete G.

  • Hero Member
  • *****
  • Posts: 2013
Re: Tradegun Sight
« Reply #9 on: October 11, 2012, 03:20:01 AM »
Thanks, guys. Looks easy enough to make from bar stock. The extra angles help a lot.

Would these things be proper on a fowling piece, or did they only show up on trade guns?
Logged

Offline Dennis Glazener

  • Administrator
  • Hero Member
  • *
  • Posts: 19483
    • GillespieRifles
Re: Tradegun Sight
« Reply #10 on: October 12, 2012, 06:21:34 PM »
The Jack Brooks trade gun sight is available here:
$25 each.  Shipping is $5.  Just send a check to Jack Brooks, 800 West Oxford Ave., Englewood, Colorado 80110. 

They are cast from an original type D trade gun.
Dennis
Logged
"I never considered a difference of opinion in politics, in religion, in philosophy, as cause for withdrawing from a friend" - Thomas Jefferson
Pages: [1]   Go Up
« previous next »