Author Topic: 15 years in the Hudson Valley  (Read 15240 times)

Online Mike Brooks

  • Hero Member
  • *****
  • Posts: 13167
    • Mike Brooks Gunmaker
15 years in the Hudson Valley
« on: September 08, 2014, 09:40:19 PM »
I started this gun 15 years ago when I bought the barrel from Benny Coogle. It sat around for years in the corner untill I found the lock for sale on this board. Sometime later I had Fred Miller inlet the barrel. I had probably 3 stocking sessions over the years with this gun finally finishing it last month.
 The barrel is 6' long, 11 bore, and 1 3/8" at the breech. I made the butplate which is 6" tall X 2" wide. The lock is a rifle shoppe lock, english ca. 1690.
 The gun is 7' 5 1/2" long and weighs 11 lbs 6 oz.
 The guy holding the gun is a bum that lives in my barn....





NEW WEBSITE! www.mikebrooksflintlocks.com
Say, any of you boys smithies? Or, if not smithies per se, were you otherwise trained in the metallurgic arts before straitened circumstances forced you into a life of aimless wanderin'?

Online Mike Brooks

  • Hero Member
  • *****
  • Posts: 13167
    • Mike Brooks Gunmaker
Re: 15 years in the Hudson Valley
« Reply #1 on: September 08, 2014, 09:43:21 PM »





Fur sale BTW ;)
NEW WEBSITE! www.mikebrooksflintlocks.com
Say, any of you boys smithies? Or, if not smithies per se, were you otherwise trained in the metallurgic arts before straitened circumstances forced you into a life of aimless wanderin'?

Offline tallbear

  • Global Moderator
  • Hero Member
  • *
  • Posts: 4013
  • Mitch Yates
Re: 15 years in the Hudson Valley
« Reply #2 on: September 08, 2014, 10:27:21 PM »
Love it Mike!!!!!!!!! What would be cooler than to take this down to my blind for duck season here in New York!!!!!Great piece!!

Mitch

Offline bama

  • Hero Member
  • *****
  • Posts: 2095
    • Calvary Longrifles
Re: 15 years in the Hudson Valley
« Reply #3 on: September 08, 2014, 11:29:21 PM »
I agree with Mitch, nicely done Mike and I also love the color. Mitch I bet you cold knock em out of the stratosphere with that baby.
Jim Parker

"An Honest Man is worth his weight in Gold"

Joe S

  • Guest
Re: 15 years in the Hudson Valley
« Reply #4 on: September 08, 2014, 11:31:34 PM »
Very cool!  I have an HV Fowler of my own in the works, so I’m not interested in your gun, but I may be interested in the barn bum.  Is he for sale?  Does he eat pigeons? How about mice?  Does he stink?

Offline chrisdefrance

  • Hero Member
  • *****
  • Posts: 759
  • Chris de France
Re: 15 years in the Hudson Valley
« Reply #5 on: September 08, 2014, 11:53:32 PM »
What gage is that bum... er  barrel ?
"These are the times that try men's souls: The summer soldier and the sunshine patriot will, in this crisis, shrink from the service of his country; but he that stands by it now, deserves the love and thanks of man and woman."

Offline smart dog

  • Global Moderator
  • Hero Member
  • *
  • Posts: 6814
Re: 15 years in the Hudson Valley
« Reply #6 on: September 09, 2014, 03:20:34 AM »
Wow,
Did that "Bum"build this gun?  Who is he?  He must be the "Magic Gunmaker".  Mike, please let him know that we think highly of his work.  I have a Berks County gun that I am about to expose that is inspired by this "Bum".

dave
"The main accomplishment of modern economics is to make astrology look good."

Offline Majorjoel

  • Hero Member
  • *****
  • Posts: 3134
Re: 15 years in the Hudson Valley
« Reply #7 on: September 09, 2014, 04:02:41 AM »
Very nice Mike! As for that bum... I always thought he was taller.....;D
« Last Edit: September 09, 2014, 04:36:36 AM by Acer Saccharum »
Joel Hall

Offline Keb

  • Hero Member
  • *****
  • Posts: 1191
  • south Ohio
Re: 15 years in the Hudson Valley
« Reply #8 on: September 09, 2014, 04:00:48 PM »
Awesome! BTW, I have a clown living in my barn.
« Last Edit: September 09, 2014, 04:03:20 PM by Keb »

Offline Hawken62_flint

  • Sr. Member
  • ****
  • Posts: 485
  • Nothing like it, 'cept more of it !
Re: 15 years in the Hudson Valley
« Reply #9 on: September 09, 2014, 04:03:12 PM »
Terrific as always---I assume you made the ramrod.  What did you make the ramrod from--obviously a tall tree or very large sapling.

Offline Robby

  • Hero Member
  • *****
  • Posts: 2592
  • NYSSR ―
Re: 15 years in the Hudson Valley
« Reply #10 on: September 09, 2014, 04:04:20 PM »
As always, a believable gun, beautifully done!!
Robby
molon labe
We the people are the rightful masters of both Congress and the courts, not to overthrow the Constitution but to overthrow the men who pervert the Constitution. A. Lincoln

Offline Acer Saccharum

  • Administrator
  • Hero Member
  • *
  • Posts: 19311
    • Thomas  A Curran
Re: 15 years in the Hudson Valley
« Reply #11 on: September 09, 2014, 04:08:39 PM »
On original guns, it's not uncommon to find that the fore end is a separate piece spliced on. Must be a practical matter.  ;)
Tom Curran's web site : http://monstermachineshop.net
Ramrod scrapers are all sold out.

Online Mike Brooks

  • Hero Member
  • *****
  • Posts: 13167
    • Mike Brooks Gunmaker
Re: 15 years in the Hudson Valley
« Reply #12 on: September 09, 2014, 06:55:55 PM »
On original guns, it's not uncommon to find that the fore end is a separate piece spliced on. Must be a practical matter.  ;)
That's a fact Jack. This one has a one piece stock.......try to find one that curly, that long on the cheap. ;)
NEW WEBSITE! www.mikebrooksflintlocks.com
Say, any of you boys smithies? Or, if not smithies per se, were you otherwise trained in the metallurgic arts before straitened circumstances forced you into a life of aimless wanderin'?

Offline Jim Kibler

  • Hero Member
  • *****
  • Posts: 4284
    • Personal Website
Re: 15 years in the Hudson Valley
« Reply #13 on: September 09, 2014, 07:42:56 PM »
In my experience most spliced fore ends I've seen spliced have been on burl maple stocks.  There's a practical limit to the  size of burl pieces that can be obtained.  These splices are commonly made by a tapered cone and matching socket type joint. 

Online Mike Brooks

  • Hero Member
  • *****
  • Posts: 13167
    • Mike Brooks Gunmaker
Re: 15 years in the Hudson Valley
« Reply #14 on: September 09, 2014, 10:25:51 PM »
Terrific as always---I assume you made the ramrod.  What did you make the ramrod from--obviously a tall tree or very large sapling.
I make all my ram rods from splits I take from an 8' hickory log the saw mill gave me a few years ago. I'm down to only 3 more split blanks...I'm not looking forward to the hammer and wedge routine again, but a guy has to do what a guy has to do.
 I should mention that there are 21' of relieved upper and lower forestock moldings on this gun. Three freakin' days of relieved forestock moldings was plenty. ;)
NEW WEBSITE! www.mikebrooksflintlocks.com
Say, any of you boys smithies? Or, if not smithies per se, were you otherwise trained in the metallurgic arts before straitened circumstances forced you into a life of aimless wanderin'?

Offline JTR

  • member 2
  • Hero Member
  • ****
  • Posts: 4202
Re: 15 years in the Hudson Valley
« Reply #15 on: September 09, 2014, 11:58:32 PM »
That's a fine looking gun!

But I always thought you were the little guy in the avatar picture though,,,,,,  :D

John
John Robbins

Offline Tommy Bruce

  • Sr. Member
  • ****
  • Posts: 439
Re: 15 years in the Hudson Valley
« Reply #16 on: September 10, 2014, 03:20:05 AM »
Pretty @!*% sweet Mike!  Rates right up there with my new type G  ;D ;D
A man can never have too much red wine, too many books or too much ammunition”
R. Kipling

Offline Kopfjaeger

  • Sr. Member
  • ****
  • Posts: 403
Re: 15 years in the Hudson Valley
« Reply #17 on: September 10, 2014, 03:36:51 PM »
Now that's a long barrel.
" A godly man and his rifle deprive sleep from the wicked, A christian man who prays is the defeater of evil, A praying man who will fight is the conqueror of nations and the hope of the oppressed "

Offline D. Taylor Sapergia

  • Member 3
  • Hero Member
  • *
  • Posts: 12524
Re: 15 years in the Hudson Valley
« Reply #18 on: September 10, 2014, 07:32:11 PM »
I wish I had money!
D. Taylor Sapergia
www.sapergia.blogspot.com

Art is not an object.  It is the excitement inspired by the object.

Offline Telgan

  • Hero Member
  • *****
  • Posts: 549
Re: 15 years in the Hudson Valley
« Reply #19 on: September 10, 2014, 11:06:13 PM »
Wha'd ya use to age up that bum? Nice patina ya got goin there. Seriously though - Very, very nice piece.
« Last Edit: September 11, 2014, 03:33:15 AM by TELGAN »

Offline Canute Rex

  • Sr. Member
  • ****
  • Posts: 360
Re: 15 years in the Hudson Valley
« Reply #20 on: September 11, 2014, 01:08:56 AM »
I understand that a mixture of bacon grease, tobacco and cheap whiskey was the traditional finish for bums.

How common were ultra-long barrels like that in ordinary gauge/caliber? I have seen punt guns that were like shoulder stocked cannons, but the bore on this one is more in line with something that you could actually shoulder. Although, I can't imagine shooting this one without a rest. Can you wing shoot with it?

It's a remarkable piece of work - congrats.

Offline Tom Currie

  • Hero Member
  • *****
  • Posts: 1294
Re: 15 years in the Hudson Valley
« Reply #21 on: September 11, 2014, 01:39:42 AM »
Really cool Mike. Congrats to that bum in your barn.

Online Mike Brooks

  • Hero Member
  • *****
  • Posts: 13167
    • Mike Brooks Gunmaker
Re: 15 years in the Hudson Valley
« Reply #22 on: September 11, 2014, 04:04:40 AM »
I understand that a mixture of bacon grease, tobacco and cheap whiskey was the traditional finish for bums.

How common were ultra-long barrels like that in ordinary gauge/caliber? I have seen punt guns that were like shoulder stocked cannons, but the bore on this one is more in line with something that you could actually shoulder. Although, I can't imagine shooting this one without a rest. Can you wing shoot with it?

It's a remarkable piece of work - congrats.
Grinslades book is full of guns like this. They were common in the Hudson valley. It is intended to be shot from the shoulder at waterfowl sitting on the water. It would be a tough gun to wing shoot with. I have had alot of luck wingshooting with a 48" barrel but it was with a 6.5lb gun not 11 1/2 lbs.
 This particular gun balances at the swell at the rear ram rod pipe.
NEW WEBSITE! www.mikebrooksflintlocks.com
Say, any of you boys smithies? Or, if not smithies per se, were you otherwise trained in the metallurgic arts before straitened circumstances forced you into a life of aimless wanderin'?

Offline smokinbuck

  • Hero Member
  • *****
  • Posts: 2959
Re: 15 years in the Hudson Valley
« Reply #23 on: September 11, 2014, 11:56:23 PM »
Mike,
Great looking gun. Ken Netting built a similar one for me, with a 6' barrel, that is 7'4" overall. Mine is a plain gun in 20 gauge and weighs in at 11#. Glad to see someone else is also a little bit crazy.
Mark
Mark

Offline TPH

  • Hero Member
  • *****
  • Posts: 923
Re: 15 years in the Hudson Valley
« Reply #24 on: September 12, 2014, 04:38:13 PM »
As always, Mike.... NICE! :)
T.P. Hern