Author Topic: New Stand for Old Anvil  (Read 10081 times)

Offline David R. Pennington

  • Hero Member
  • *****
  • Posts: 2885
New Stand for Old Anvil
« on: September 18, 2017, 09:25:39 PM »
New anvil stand. After a few sessions of heavier forging and welding I determined my anvil height was too tall and the anvil wanted to twist and jump around on the stump so I fixed a new stand with some scrap lumber. I nailed a couple pieces of treated 1x8 on the bottom since it will rest on the dirt floor. I made two half moons out of inch poplar and chamfered the curved side to roughly correspond to the anvil bases taper. They are locked down with a 5/8 carriage bolt on each side and it is secure!
[/url

[url=http://ibb.co/dyHi15]


private image sharing
« Last Edit: January 14, 2020, 02:33:57 AM by rich pierce »
VITA BREVIS- ARS LONGA

Black Hand

  • Guest
Re: New Stand for Old Anvil
« Reply #1 on: September 19, 2017, 03:33:43 AM »
Nice stand!
Is your anvil bleeding?

Offline David R. Pennington

  • Hero Member
  • *****
  • Posts: 2885
Re: New Stand for Old Anvil
« Reply #2 on: September 19, 2017, 02:03:40 PM »
Some previous owner spilled red paint on it.
VITA BREVIS- ARS LONGA

Offline okieboy

  • Hero Member
  • *****
  • Posts: 818
Re: New Stand for Old Anvil
« Reply #3 on: September 19, 2017, 10:00:09 PM »
 I like it. I would like to see more of the shop that it is sitting in.
Okieboy

Offline David R. Pennington

  • Hero Member
  • *****
  • Posts: 2885
Re: New Stand for Old Anvil
« Reply #4 on: September 20, 2017, 05:02:42 AM »





« Last Edit: January 14, 2020, 02:34:26 AM by rich pierce »
VITA BREVIS- ARS LONGA

Offline jrb

  • Sr. Member
  • ****
  • Posts: 290
Re: New Stand for Old Anvil
« Reply #5 on: September 22, 2017, 11:59:57 PM »
It's all extremely nice!!!

Offline msellers

  • Hero Member
  • *****
  • Posts: 599
Re: New Stand for Old Anvil
« Reply #6 on: September 23, 2017, 02:44:08 AM »
Jealous of your shop and forge set up. Looks like a vey good using and working space/set up.

Offline David R. Pennington

  • Hero Member
  • *****
  • Posts: 2885
Re: New Stand for Old Anvil
« Reply #7 on: September 23, 2017, 04:11:56 AM »
Thanks, I have really been enjoying it. After going from a little rivet forge outside I feel like I am in heaven. I have good coal and a nice deep tuyre, don't have to worry about the weather. I have been forging almost every evening this week. I can get welding heats no problem now. I have been tweaking things and getting set up. Moved my grindstone in this afternoon. Hope to get the bellows rebuilt soon and installed. Working tempoarily with hair dryer!
VITA BREVIS- ARS LONGA

Offline Shreckmeister

  • Hero Member
  • *****
  • Posts: 3749
  • GGGG Grandpa Schrecengost Gunsmith/Miller
Re: New Stand for Old Anvil
« Reply #8 on: September 26, 2017, 07:24:44 AM »
Wonderful forge. Reminds me of Schreckengosts shop
Rightful liberty is unobstructed action according to our will within limits drawn around us by the equal rights of others. I do not add 'within the limits of the law' because law is often but the tyrant's will, and always so when it violates the rights of the individual.

gizamo

  • Guest
Re: New Stand for Old Anvil
« Reply #9 on: September 30, 2017, 02:18:14 AM »
I keep coming back to look at the pics of Davids shop....
Working on my own right now...and draw some inspiration from his accomplishments.

Offline David R. Pennington

  • Hero Member
  • *****
  • Posts: 2885
Re: New Stand for Old Anvil
« Reply #10 on: September 30, 2017, 01:37:11 PM »
This is the best thing I have done for my self preservation. They say the best thing for arthritis is to keep moving. It is a lot easier to do if it is something you enjoy doing. I only wish I had made it larger. I was worried some about dirt floor, but find it is working out great. A lot easier on my feet than a solid floor. I wet the floor down ocasionally to keep down dust and find this also helps cool the shop down some.
VITA BREVIS- ARS LONGA

Offline looper

  • Full Member
  • ***
  • Posts: 139
Re: New Stand for Old Anvil
« Reply #11 on: October 17, 2017, 06:11:20 AM »
Did you do the masonry work yourself? I've got something very similar planned.

Offline David R. Pennington

  • Hero Member
  • *****
  • Posts: 2885
Re: New Stand for Old Anvil
« Reply #12 on: October 18, 2017, 04:50:21 AM »
Yes, I did it all good or bad. I laid it out like a fireplace, but if I were to do another I would make the hearth opening lower, (see the sheet iron fix I put in). It actually draws well, but until the chimney got good and warm it would smoke out some with a green coal fire. Lowering the hearth opening with the little metal hood fixes it pretty good. The big deep commercial tuyre is great.
 Just finished up my hinges and hung the shop doors today.
VITA BREVIS- ARS LONGA

Offline Nordnecker

  • Hero Member
  • *****
  • Posts: 1209
Re: New Stand for Old Anvil
« Reply #13 on: October 18, 2017, 03:16:20 PM »
That's a very tidy looking smithy you have there! I have a dirt floor in mine, too. I wouldn't trade it for anything.
I have a second side door about 10 feet away from my forge. If I leave it open, my forge will smoke. As long as it's closed, no problem.
"I can no longer stand back and allow communist infiltration, communist indoctrination and the international communist conspiracy to sap and impurify our precious bodily fluids."- Gen Jack T. Ripper

Offline David R. Pennington

  • Hero Member
  • *****
  • Posts: 2885
Re: New Stand for Old Anvil
« Reply #14 on: October 18, 2017, 03:30:56 PM »
The shop I work sometimes at a museum has an open hearth forge with a hood. There are two doors and one window. It is set up with an anvil on either side of the forge. There is one window that if you open it sometimes it will smoke the smith on the other side out.
VITA BREVIS- ARS LONGA

Offline David R. Pennington

  • Hero Member
  • *****
  • Posts: 2885
Re: New Stand for Old Anvil
« Reply #15 on: October 19, 2017, 03:54:37 AM »
New doors temporarilly installed to check for fit. I will pull them back off and paint the doors then reinstall with nails I made for the purpose.



« Last Edit: January 14, 2020, 02:34:51 AM by rich pierce »
VITA BREVIS- ARS LONGA

Offline looper

  • Full Member
  • ***
  • Posts: 139
Re: New Stand for Old Anvil
« Reply #16 on: October 19, 2017, 06:31:29 AM »
Very nice.

Offline Pukka Bundook

  • Hero Member
  • *****
  • Posts: 3342
Re: New Stand for Old Anvil
« Reply #17 on: November 04, 2017, 03:51:42 PM »
Grand way of holding your anvil down, David!!

Beats my old bolts belted into the log and bent over around its ankles! LOL!  Must do it your way. Never thought of that!

Thanks.:-)

Richard.

Offline Curt Lyles

  • Curt’s Blacksmith Shop
  • Sr. Member
  • ****
  • Posts: 420
    • Curt's Blacksmith Shop
Re: New Stand for Old Anvil
« Reply #18 on: February 08, 2018, 01:25:13 PM »
  David that is a very nice lookin set up you have.  Curt

Offline David R. Pennington

  • Hero Member
  • *****
  • Posts: 2885
Re: New Stand for Old Anvil
« Reply #19 on: February 09, 2018, 01:32:57 AM »
Thanks Curt, If all goes well I hope to have bellows completed tomorrow.
VITA BREVIS- ARS LONGA

Offline Robert Wolfe

  • Hero Member
  • *****
  • Posts: 1267
  • Great X Grandpa
Re: New Stand for Old Anvil
« Reply #20 on: February 09, 2018, 05:44:59 PM »
Can't wait to see the bellows installed.
Robert Wolfe
Northern Indiana

Offline whitebear

  • Hero Member
  • *****
  • Posts: 837
Re: New Stand for Old Anvil
« Reply #21 on: December 25, 2018, 06:28:49 AM »
Would you mind sending me some measurements of your anvil stand.  My son is doing very well at blacksmithing but his stump is outdoors and is rotting away.
In the beginning God...
Georgia - God's vacation spot