Author Topic: Shaving Horse  (Read 5298 times)

Offline Robert Wolfe

  • Hero Member
  • *****
  • Posts: 1267
  • Great X Grandpa
Shaving Horse
« on: May 03, 2018, 10:21:20 PM »
I just finished this shaving horse. I always wanted one and it finally got to the top of my list. An oak tree came down in my woods last summer and I split it up to make the boards. No store-bought lumber here. The legs were from an oak pole I had cut years ago that had been stuck up in my barn rafters. I wanted well-seasoned wood for the legs so that they wouldn’t shrink and come loose. The green oak bench will also shrink around the legs keeping them tight. The only thing not from my woods are the two pins/axles that the work table and treadle frame pivot on. I fired up the forge last weekend at a local living history event and finally got them finished. 



« Last Edit: January 31, 2022, 07:23:52 PM by Tim Crosby »
Robert Wolfe
Northern Indiana

Offline Greg Pennell

  • Hero Member
  • *****
  • Posts: 1519
Re: Shaving Horse
« Reply #1 on: May 04, 2018, 02:03:28 AM »
Nice one!  I had one years ago when I was doing a lot of primitive archery...they sure are handy to have around. Yours might inspire me to build another.  Thanks for sharing!

Greg
“Let your gun therefore be the constant companion of your walks” Thomas Jefferson

Offline David R. Pennington

  • Hero Member
  • *****
  • Posts: 2885
Re: Shaving Horse
« Reply #2 on: May 04, 2018, 03:40:24 AM »
Very nice Robert. I’ve been meaning to fix one for a while too.
VITA BREVIS- ARS LONGA

Offline Robert Wolfe

  • Hero Member
  • *****
  • Posts: 1267
  • Great X Grandpa
Re: Shaving Horse
« Reply #3 on: May 07, 2018, 08:21:14 PM »
Just to confirm that this thread is gun related ( ;)), I used the shaving horse yesterday to hold a 1/2 inch hickory dowel that I needed to taper down to 5/16 (edited - thanks Sawfiler!) for a 12 gauge fowling gun ramrod. If you haven't used Acer's ramrod scraper you're missing something fine. The horse worked great too.


]=https://ibb.co/i8RuES][
« Last Edit: January 31, 2022, 07:49:27 PM by Tim Crosby »
Robert Wolfe
Northern Indiana

Offline Bigmon

  • Hero Member
  • *****
  • Posts: 1279
Re: Shaving Horse
« Reply #4 on: May 07, 2018, 09:02:17 PM »
I have one of these my Dear Old Daddy made long ago.  He called it a "Cooper's Mare"

Offline WadePatton

  • Hero Member
  • *****
  • Posts: 5274
  • Tennessee
Re: Shaving Horse
« Reply #5 on: May 07, 2018, 10:44:34 PM »
Most excellent.  I need one of these too. Love drawing, never have proper hold on stuff.
Hold to the Wind

Offline Sawfiler

  • Full Member
  • ***
  • Posts: 186
Re: Shaving Horse
« Reply #6 on: May 08, 2018, 03:10:57 PM »
I need to learn the trick of tapering a 1/2 inch dowel down to 5/8!!
Wish I enjoyed what makes my living
Did what I do with a willin' hand
Some would run, ah, but that ain't like me
So I just dream and keep on bein' the way I am

Offline Bob Roller

  • Hero Member
  • *****
  • Posts: 9300
Re: Shaving Horse
« Reply #7 on: May 08, 2018, 03:55:25 PM »
I need to learn the trick of tapering a 1/2 inch dowel down to 5/8!!

I hope you're NOT using common hardware store wood dowels for ram rods.
They are not suitable for any job involving push/pressure like loading a rifle.
I have seen them break and saw one man taken to the nearest hospital from
the Friendship range with a section of 1/2" dowel still thru his hand.

Bob Roller

Offline WadePatton

  • Hero Member
  • *****
  • Posts: 5274
  • Tennessee
Re: Shaving Horse
« Reply #8 on: May 08, 2018, 05:35:18 PM »
I need to learn the trick of tapering a 1/2 inch dowel down to 5/8!!

mathematical marvels?   ;D


Heck no Bob, we make wood round for anything more serious than a hat peg.  Good note for the un-washed though.
« Last Edit: May 08, 2018, 05:35:49 PM by WadePatton »
Hold to the Wind

Offline Robert Wolfe

  • Hero Member
  • *****
  • Posts: 1267
  • Great X Grandpa
Re: Shaving Horse
« Reply #9 on: May 08, 2018, 06:01:05 PM »
Oops - 5/16th! Thanks Sawfiler.......

No Bob, it was a 1/2 inch hickory ramrod blank from Larry Zorne.
« Last Edit: May 08, 2018, 06:04:26 PM by Robert Wolfe »
Robert Wolfe
Northern Indiana

Offline Nordnecker

  • Hero Member
  • *****
  • Posts: 1208
Re: Shaving Horse
« Reply #10 on: May 14, 2018, 02:43:14 PM »
I had one years ago, loaned it to someone and never saw it again. It had a trunion for the front legs. In other words, the plank was cut down leaving a round tenon sticking out. The front legs were morticed into a square board about 16" long. In the middle of this board was an oval shaped hole. The tennon went through this hole and had a wedge pin that tightened up in it's own mortice so it didn't press against the other board. Really simple but hard to explain. It was a great design because the front leg "trunion" would self adjust for uneven ground. It gave the stability of 4 legs but always sat flat like 3 legs.
"I can no longer stand back and allow communist infiltration, communist indoctrination and the international communist conspiracy to sap and impurify our precious bodily fluids."- Gen Jack T. Ripper

Offline Robert Wolfe

  • Hero Member
  • *****
  • Posts: 1267
  • Great X Grandpa
Re: Shaving Horse
« Reply #11 on: May 14, 2018, 04:51:02 PM »
I think I can picture it - sounds like a neat way of constructing one.
Robert Wolfe
Northern Indiana

Offline Nordnecker

  • Hero Member
  • *****
  • Posts: 1208
Re: Shaving Horse
« Reply #12 on: May 15, 2018, 03:26:41 PM »


Here's a clumsey drawing of it. It was neat, and always sat still.
« Last Edit: January 31, 2022, 07:31:04 PM by Tim Crosby »
"I can no longer stand back and allow communist infiltration, communist indoctrination and the international communist conspiracy to sap and impurify our precious bodily fluids."- Gen Jack T. Ripper

Offline Curtis

  • Hero Member
  • *****
  • Posts: 2184
  • Missouri
Re: Shaving Horse
« Reply #13 on: May 19, 2018, 06:13:10 AM »
That is awesome Robert!  I have some oak planks sawed up and waiting in my garage for me to make a shaving horse with.  Guess I need to get busy with it, you have inspired me!!

Curtis
Curtis Allinson
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Sometimes, late at night when I am alone in the inner sanctum of my workshop and no one else can see, I sand things using only my fingers for backing

galudwig

  • Guest
Re: Shaving Horse
« Reply #14 on: May 26, 2018, 02:15:09 PM »
That's pretty cool Robert. I particularly like the forge work on the axles. If you bring it to Canter's Cave next January, we can all try our hand at tapering ramrods!  8)
« Last Edit: May 26, 2018, 02:16:58 PM by galudwig »

Offline Robert Wolfe

  • Hero Member
  • *****
  • Posts: 1267
  • Great X Grandpa
Re: Shaving Horse
« Reply #15 on: May 26, 2018, 04:35:30 PM »
Thanks. It was a lot of fun to build. The metal work was icing on the cake!
Robert Wolfe
Northern Indiana

Offline will payne

  • Sr. Member
  • ****
  • Posts: 349
  • AKA dead eye/ Coder /Ethical Hacker
Re: Shaving Horse
« Reply #16 on: June 24, 2018, 11:23:30 PM »
That looks nicer than the ones I've seen.
🕯
Will


"The strongest reason for the people to retain the right to keep and bear arms is, as a last resort, to protect themselves against tyranny in government." -Thomas Jefferson

Offline Robert Wolfe

  • Hero Member
  • *****
  • Posts: 1267
  • Great X Grandpa
Re: Shaving Horse
« Reply #17 on: June 25, 2018, 05:17:00 AM »
Thanks - I used it just today to make a new handle for one of my hammers.
Robert Wolfe
Northern Indiana