Author Topic: Making The Walking Stick  (Read 626 times)

Offline Tim Crosby

  • Administrator
  • Hero Member
  • *
  • Posts: 11019
  • AKA TimBuckII
Making The Walking Stick
« on: July 20, 2019, 10:07:10 PM »
 First Two show the stick after it was tapered on a jointer. The top was left Octagonal to make it easer to hold. The numbers are so I know where I am working, the line is at the cutoff length. At the bottom of the second you can see where a Hole saw was used to make the step for the tip, a Pic farther down shows it trimmed up. The Brass tip is threaded 5/16-24 as is the hole and the tip was screwed in. The psrt that goes into the handle was done the same way but is pinned instead of a bolt.







 The next Two show the holes that were drilled in the antler and the screws that were put in to anchor the Pewter.







 This one shows how the dams were made that the Pewter was poured into.





 After the pour.





 Next Two show all Three poured and roughed out.







 This is the piece the tip was turned from.





 The shaft trimmed up some, at the bottom you can see the area where the tip will go.





 The last show my Jack-leg set-up for truing up the shaft. And my helpers











« Last Edit: July 20, 2019, 10:28:50 PM by Tim Crosby »

Offline Mick C

  • Full Member
  • ***
  • Posts: 246
Re: Making The Walking Stick
« Reply #1 on: July 21, 2019, 12:37:05 AM »
Wow, neat post.  Thanks for showing your process, Tim.
My profile picture is my beloved K9 best friend and soulmate, Buster Brown, who passed away in 2018.  I miss you buddy!

Offline Marcruger

  • Hero Member
  • *****
  • Posts: 1633
Re: Making The Walking Stick
« Reply #2 on: July 21, 2019, 03:43:59 PM »
Good gracious that is a complicated project.  I am not brave enough to try something like that.  I look forward to seeing the finished stick at CLA.   :-) 

Offline g.pennell

  • Hero Member
  • *****
  • Posts: 679
Re: Making The Walking Stick
« Reply #3 on: July 21, 2019, 04:44:27 PM »
Neat-o!  Tim, that's a heckuva project for sure...I especially like that red-neck lathe to turn that shaft round...ingenious!

Greg
“Let your gun therefore be the constant companion of your walks” Thomas Jefferson

Offline hanshi

  • Hero Member
  • *****
  • Posts: 3900
  • My passion is longrifles!
    • martialartsusa.com
Re: Making The Walking Stick
« Reply #4 on: July 21, 2019, 10:53:58 PM »
Yes, quite complicated.  Anxious to see the finished stick.
!Jozai Senjo! "always present on the battlefield"
Young guys should hang out with old guys; old guys know stuff.

Offline Nessmuck

  • Full Member
  • ***
  • Posts: 183
Re: Making The Walking Stick
« Reply #5 on: August 09, 2019, 10:00:09 PM »
Very nice....but I just grab my walking stick off a beaver dam....all the bark is already chewed off,with some nice markings...and it hardwood too....and Free !

Offline webradbury

  • Sr. Member
  • ****
  • Posts: 325
Re: Making The Walking Stick
« Reply #6 on: August 10, 2019, 05:42:11 PM »
Beavers do make some nice walking sticks.  I must admit I once blew up their woodworking shop, though.
I love the smell of Walnut shavings in the morning!