AmericanLongRifles Forums

General discussion => Contemporary Accoutrements => Topic started by: Dan Fruth on July 08, 2023, 07:14:13 PM

Title: ramrod worm
Post by: Dan Fruth on July 08, 2023, 07:14:13 PM

This is the same size as the rod and slides into the entry hole.


(https://i.ibb.co/4TvNBsm/IMG-1479.jpg) (https://ibb.co/NjDYw1V)



(https://i.ibb.co/TM76sKm/IMG-1480.jpg) (https://ibb.co/23CxT8g)

Title: Re: ramrod worm
Post by: Clark Badgett on July 08, 2023, 07:33:12 PM

Is this a new offering?

Title: Re: ramrod worm
Post by: Dan Fruth on July 08, 2023, 08:10:49 PM

Yes it is

Title: Re: ramrod worm
Post by: Brokennock on July 08, 2023, 09:13:03 PM

Quote from: Dan Fruth on July 08, 2023, 07:14:13 PM

This is the same size as the rod and slides into the entry hole.


(https://i.ibb.co/4TvNBsm/IMG-1479.jpg) (https://ibb.co/NjDYw1V)



(https://i.ibb.co/TM76sKm/IMG-1480.jpg) (https://ibb.co/23CxT8g)

That's awesome. How much does it taper?
The #1 gun I would want to put one of these with is tricky with ramrod size. Each pipe from front to entry pipe is slightly smaller.

Title: Re: ramrod worm
Post by: Nessmuck on July 09, 2023, 05:54:29 AM

Ok...so what am I looking at here ?

I have one of your worms already.
What does this set up do ? And thanks

Title: Re: ramrod worm
Post by: Dan Fruth on July 09, 2023, 03:45:03 PM

This is small enough to fit permanently on your ramrod. It is .03 smaller than the ramrod hole diameter and is always in the gun   I have collected several originals of this type.

Title: Re: ramrod worm
Post by: TDM on July 09, 2023, 09:21:06 PM

That is very neat!

Title: Re: ramrod worm
Post by: Marcruger on July 10, 2023, 03:13:35 AM

I have two of Dan's reversible worms.  They are as good a quality as anyone has a right to expect.  Like little jewels.  Nicely done Dan.   God Bless,   Marc

Title: Re: ramrod worm
Post by: stumbling buffalo on August 05, 2023, 05:49:36 PM

Dan,

This looks like the perfect size to clean out the ignition chamber of a patent breech.  Am I off base or do you think that will work?

Thanks, Guy

Title: Re: ramrod worm
Post by: Cades Cove Fiddler on August 08, 2023, 06:28:11 PM

 :o ;) :) :)... I like this,... !!! ... what is the smallest calibre size you make,...?

Title: Re: ramrod worm
Post by: Dan Fruth on August 09, 2023, 05:31:43 AM

I make these 1/32 smaller than 5/16 and 3/8

Title: Re: ramrod worm
Post by: Curtis on August 09, 2023, 06:42:09 AM

Well Dan, now you have done it.  Looks like I may have to purchase yet another worm from you!!!!!  8)


Curtis

Title: Re: ramrod worm
Post by: Cory Joe Stewart on August 09, 2023, 03:04:04 PM

Nifty

Title: Re: ramrod worm
Post by: Dan Fruth on August 09, 2023, 04:55:36 PM

I'll have plenty!!  See you at the CLA!

Title: Re: ramrod worm
Post by: Nessmuck on August 20, 2023, 05:48:20 PM

Any videos of this set up ? And thanks

Title: Re: ramrod worm
Post by: Huckleberry on September 12, 2023, 05:07:27 AM

Mr. Fruth - I sent you a PM

Title: Re: ramrod worm
Post by: Dan Fruth on September 14, 2023, 04:10:39 AM

I sent you a response. Thanks