AmericanLongRifles Forums
General discussion => Black Powder Shooting => Topic started by: Nessmuck on April 05, 2019, 03:26:52 PM
-
Just putting it out there....I don’t shoot in any matches....but a rear sight would help. Or be a purist and tough it out...lol ...What say you. .... and if I had to sell the gun ,could it devalue it ?
-
If you're not shooting matches I'd put one on. I've seen many old fowling guns with rear sights that were probably put on sometime after the gun was initially built.
-
You can always make a slug to fit the dovetail. Lots of old rifles have old dovetails for rear sights filled in.
-
I get good accuracy on my smoothbores without a rear sight by lining up the front bead with the shadow of the tang screw
-
There's one on my smoothbore. I shoot it same as I shoot rifles with no adjustment needed.
-
Iam going up to David Prices Flintlock shop tomorrow....he’s going to Solder on a new “Turtle” sight on my Tulle....cuz I filled it down to much....trying to raise my group ( its my first smooth bore ,so stop laughing). And ....I just might have him install a rear sight too !
-
I like it better without one. Takes a bit of practice to get the hang of it. But after a while I have to wonder if a rear sight would be of any help at all.
-
I have 2 smoothbore long guns, one in the Tule F.d.C. style. I can shoot okay without the rear sight at the range in normal positions with good form, but things change a bit in the field with some shots in awkward positions, it changes the relation of your eye (the rear sight) to the rest of the gun and front sight. I definitely prefer having the rear sight.
Type G British trade guns had a rear sight, so a smoothbore with a rear sight during colonial times isn't unheard of. No documented examples of Tule guns having them that I'm aware of, but I'm not an expert.
I've seriously considered putting a very small unobtrusive rear sight on my Centermark Tule F.d.C.
-
Put a peep sight on the tang screw. Simple piece of metal that is easily removed. Drill the peep as big as needed.
(https://i.ibb.co/41W33WH/tang-picture-001.jpg) (https://ibb.co/y40770r)
-
I don't use a rear sight on my smoothbores. I know what sight picture I need . Basically , I shot it when building it and when I had a group, I worked on the stock until my cheek /hold was comfortable and the gun naturally comes into that position. Dead on at 25 yards. Raise my head a tad and it's on at 50 yards. I can visualize a rear sight in place. Hope this makes sense.
-
(https://i.ibb.co/wgDyMfn/F27-B8-BE4-D419-455-A-84-EC-1-AA400-DA2-A70.jpg) (https://ibb.co/JtXn59Y)
I taught myself to shave with a Straight 10 years ago...and keep them sharp. So I can learn new things that have a learning curve.....but Iam on the fence with the rear sight...but I do like the peep sight,a lot ! Thanks !
-
I think with enough practice you don't need one. I don't practice much. I left the Queen Anne tang bolt(which threads up from the bottom) long on my new England fouler so the threaded end sticks up above the tang to use as a sight. This really helps me turkey hunting as without using the sight, I shot too high. In competition where rear sights are banned, I have a shorter screw I install.
-
Put a peep sight on the tang screw. Simple piece of metal that is easily removed. Drill the peep as big as needed.
(https://i.ibb.co/41W33WH/tang-picture-001.jpg) (https://ibb.co/y40770r)
r
Thanks....gonnah use your idea. Will post pics when complete.
-
I have 5 of those holed magnets coming for testing on both rifles and smoothbore.
-
Smooth bores usually short range shooting, 50 yds. or less. Our club matches are 25/50 & can’t have a rear sight.. I find to stay consistent (with a smooth bore)ya gotta shoot it pretty regular.
Don’t have one on my Tulle, if I hunted with it I would see if it helped me. Good luck,
Kent