AmericanLongRifles Forums
General discussion => Black Powder Shooting => Topic started by: AZ Longrifle on October 10, 2009, 03:08:40 AM
-
I just bought a really cool Canadian made Matchlock Musket and need all cotton 3/8" diameter rope for it.
Once I have that, I can go to the Hobby shop and buy a jar of Saltpeter to mix a solution to soak the rope in it, to keep it smoldering.
I went and bought some cotton rope at the Hardware store, but, it had a plastic core in it. That will not work.
Now I have 50' of new clothes line!
Any suppliers out there?
Thank you!
-
you might try hemp cord
https://frontierfolk.ipower.com/cgi-bin/ecommerce/ac/agora.cgi?cart_id=8891811.30534*7H8pH0&product=cordage
-
Might try cotton sash cord.
-
Try cotton mop heads. I have used them for years in my fire start kit
-
AZ
I understand that if you cut your washline in two foot sections it is easy to pull the nylon center out. That helps in getting the rope to soak up the potasium nitrate. When I tried hemp cord only the outside layers soaked up the nitrate. It was wound very tight. I know my nitrate was good because the three strands of cord would unwind an inch on the end while soaking. Those ends burned with a lot of sizzle. FWIW
volatpluvia
-
You've piqued my interest. Show us a picture or two please.
-
Dixie Gun Works used to sell it. Don't know if they still do.
-
Potassium nitrate is what I've used on Sharps combustible paper cartridges. Many old fashioned hardware stores carry it disguised as "stump killer" powder. Just make a saturated solution. Lon
-
A friend of mine has been shooting a matchlock caliver for a while and seems to have the techniques down pat. He searched around for just the right slow match material and did a lot of research. He ended up buying hemp cord and braiding his own 3/8" match. You used to be able to find 3/8" braided hemp, but not lately.
He had tried braided cotton but it would fray out into a big dandelion head. Twisted rope was useless. What you want is the end of the match to look like a glowing cone. His hand braided line did that.
He tried soaking it in saltpeter but found that it spat sparks. He was worried about accidental ignition and ditched that. The best treatment he found (from 17th century texts) was to soak the braided cord in vinegar to leach out the lignin from the hemp. That made it burn hotter. He'd rinse it in water and then soak it in a baking soda solution to neutralize the acid and then rinse again. Then he would air dry it. He can light it with flint, steel, and charcloth and it glows nicely.
I'd recommend doing a web search for hemp cord and see if you can find someone who is still selling the 3/8" stuff. If not, get some finer cord and braid your own. You might try this stuff, although at 5.6mm it's a bit small: http://www.rawganique.com/Dept-Hemp-Accessories/hemp-braided-cords.htm
Have fun and don't underestimate the matchlock. My friend holds his own with the flinters.
-
He had tried braided cotton but it would fray out into a big dandelion head. Twisted rope was useless. What you want is the end of the match to look like a glowing cone. His hand braided line did that.
I have very limited experience with slow match but I can save you the trouble of web searching, round braided hemp bigger than 5.6-5.7mm (0.228") doesn't exist anymore (flat braid is still available but the spec's vary greatly from mfg to mfg). Twisted hemp also dandelions too. All the searching I did turned up nothing for double-braided 100% cotton in 5/16" & 3/8" outside of China. New cotton sash cord & wash line is cotton over synthetic, cotton/synthetic blend or contains colored synthetic tracer threads.
I'd also like to see some pic's.
-
Years ago, I cleaned some wadding from a cannon pulled from a 1733 wreck. It appeared to be somewhat coarse and maybe hemp. It was flat braided like a pigtail. After I dried some of it, it burned with a nice glow on the end and smelled like a firecracker. Either they were using matchord/linstock chord for wadding or the chord got nitrate during its long stay in the cannon bore with the powder charge.
James Levy
-
Thank you for all of the great suggestions and info on how to make match cord.
I tried my hand using Canute's instructions and the Hemp rope soaked and rinsed works very well and burns hot. I also took the plastic center out of the cotton rope, as per volatpluvia, and found that to work very well too. So I can use up the 50' of cord too. I just have to relight it after a while.
Here's my pics of the new Matchlock Gun from Canada. It came from militaryheritage.com.
Very nice guys there and great service to the USA. I had it in my hands in 1 week!
Weight on the gun is 8.6lbs. Lighter than it looks.
I have next to go and shoot it this weekend and will post a report on it using 75 grns of FFG powder and shot.
Thank you all again!
(https://americanlongrifles.org/forum/proxy.php?request=http%3A%2F%2Fi20.photobucket.com%2Falbums%2Fb201%2FCapitalOrdnance123%2FIMG_3129.jpg&hash=06fef72521e284476c44f491f34d2a81a9594ad5)
(https://americanlongrifles.org/forum/proxy.php?request=http%3A%2F%2Fi20.photobucket.com%2Falbums%2Fb201%2FCapitalOrdnance123%2FIMG_3128.jpg&hash=ecbba2c3001bf822c2fc0d44bf94037cdeb87625)