« previous next »
Pages: [1]   Go Down

Author Topic: first try at inletting fowler butt plate  (Read 6053 times)

Bioprof

  • Guest
first try at inletting fowler butt plate
« on: July 01, 2008, 07:44:19 AM »
I almost thought I had bit off more than I could chew when I started inletting a fowler-style butt plate on my snaphaunce carbine project.  The hardest part was closing up the gap at the top corners of the heel where there's a little concave recess.  It looks like there might be a 1/32" gap there, but I think I can close it up by "persuasion".   It's hard to tell from the picture, but  the tang is actually inlet below the surface of the wood.  I cut out the butt plate from one of Reaves Goehring's "the blob".    It sure is a lot of metal to inlet.

btw, I still have a lot of wood to remove from the left side of the stock.
« Last Edit: July 01, 2008, 07:46:24 AM by Bioprof »
Logged

Offline bob in the woods

  • Hero Member
  • *****
  • Posts: 4555
Re: first try at inletting fowler butt plate
« Reply #1 on: July 01, 2008, 01:33:50 PM »
That is looking really good. You've done a great job.
Logged

lew wetzel

  • Guest
Re: first try at inletting fowler butt plate
« Reply #2 on: July 01, 2008, 04:25:34 PM »
i have heard reaves has such a thing,i got a buttplate that is to short and would like to return it for the "blob".he should be at the cla show in aug.i should take it with me.
Logged

Offline Dennis Glazener

  • Administrator
  • Hero Member
  • *
  • Posts: 19483
    • GillespieRifles
Re: first try at inletting fowler butt plate
« Reply #3 on: July 01, 2008, 04:46:21 PM »
I have one here if you need it before the CLA show or Reaves does not have them with him at the CLA.
Dennis

Quote
i have heard reaves has such a thing,i got a buttplate that is to short and would like to return it for the "blob".he should be at the cla show in aug.i should take it with me.
Dennis
Logged
"I never considered a difference of opinion in politics, in religion, in philosophy, as cause for withdrawing from a friend" - Thomas Jefferson

Offline Stophel

  • Hero Member
  • *****
  • Posts: 4532
  • Chris Immel
Re: first try at inletting fowler butt plate
« Reply #4 on: July 01, 2008, 07:36:15 PM »
Looks like you did fine.  You might find it easier to inlet the buttplate if you go ahead and shape the butt down closer to final shape before inletting.  You will have a lot less extra wood to have to inlet through, and you will actually end up with a neater inlet because of that.

It took me a long time to set aside my ideas that I had to leave myself a lot of extra wood.  Hard habit to break, but once I did, I was glad of it.
Logged
When a reenactor says "They didn't write everything down"   what that really means is: "I'm too lazy to look for documentation."

Roy S.

  • Guest
Re: first try at inletting fowler butt plate
« Reply #5 on: July 02, 2008, 02:45:36 AM »
Quote from: Stophel on July 01, 2008, 07:36:15 PM
Looks like you did fine.  You might find it easier to inlet the buttplate if you go ahead and shape the butt down closer to final shape before inletting.  You will have a lot less extra wood to have to inlet through, and you will actually end up with a neater inlet because of that.

It took me a long time to set aside my ideas that I had to leave myself a lot of extra wood.  Hard habit to break, but once I did, I was glad of it.

yep same here... well it didn't take that long to figure lol.   ::)
Logged

lew wetzel

  • Guest
Re: first try at inletting fowler butt plate
« Reply #6 on: July 03, 2008, 07:34:09 PM »
dennis ,pm sent.
Logged
Pages: [1]   Go Up
« previous next »