« previous next »
Pages: [1]   Go Down

Author Topic: A couple of noggin's  (Read 7149 times)

Offline David Rase

  • Hero Member
  • *****
  • Posts: 4320
  • If we need it here, make it here. Charlie Daniels
A couple of noggin's
« on: March 13, 2015, 12:33:59 AM »
Been playing around with my new wood lathe again this week.  Decided to put some of the knowledge I learned from my local wood turners club on turning to the test.  Pictured are 3 noggins I made.  One is from curly maple, one from English walnut and the third from black cherry.  They were a little more work than I originally thought, though I did cut my time in half from 6 hours for the first one to 3 hours for the next 2.  Learning curve was good.  These are about 4" diameter.

 

Logged

Offline skillman

  • Hero Member
  • *****
  • Posts: 996
  • The Usual Suspect
Re: A couple of noggin's
« Reply #1 on: March 13, 2015, 02:00:52 AM »
Those really came out neat Dave. I think I see how you did it and it's a pretty slick idea. @!*% lathe's are addictive, aren't they?

Steve
Logged
Steve Skillman

Offline Kermit

  • Hero Member
  • *****
  • Posts: 3099
Re: A couple of noggin's
« Reply #2 on: March 13, 2015, 02:32:24 AM »
I'm thinking about that handle tab whizzing around... ;)
« Last Edit: March 16, 2015, 06:41:25 PM by Kermit »
Logged
"Anything worth doing is worth doing slowly." Mae West

Offline David Rase

  • Hero Member
  • *****
  • Posts: 4320
  • If we need it here, make it here. Charlie Daniels
Re: A couple of noggin's
« Reply #3 on: March 13, 2015, 03:23:58 AM »
Quote from: Kermit on March 13, 2015, 02:32:24 AM
I'm thinking about that handle tab whiz zing around... ;)
Like Aretha Franklin said: R.E.S.P.E.C.T.  Actually I can only spin the blanks about 750 to 800 RPM.  Still enough to get your attention! :o
David
Logged

Offline iloco

  • Hero Member
  • *****
  • Posts: 1029
  • Old Timer, Chilhowie, Va.
Re: A couple of noggin's
« Reply #4 on: March 13, 2015, 04:24:32 AM »
Those are some nice noggins.  When my shop warms up I have some Maple Burl I bought in either Washington State or Oregon a few years back.  It should make some nice ones.  With the right chucks those little handle tabs should not be any problem.
Logged
iloco

Offline David Rase

  • Hero Member
  • *****
  • Posts: 4320
  • If we need it here, make it here. Charlie Daniels
Re: A couple of noggin's
« Reply #5 on: March 13, 2015, 05:20:29 AM »
Quote from: iloco on March 13, 2015, 04:24:32 AM
Those are some nice noggins.  When my shop warms up I have some Maple Burl I bought in either Washington State or Oregon a few years back.  It should make some nice ones.  With the right chucks those little handle tabs should not be any problem.
Yep, now that I have practiced and have a method I am ready to get a couple of burls and do it up right. 
David
Logged

Offline smallpatch

  • Hero Member
  • *****
  • Posts: 4107
  • Dane Lund
Re: A couple of noggin's
« Reply #6 on: March 13, 2015, 05:24:22 AM »
Wow David,  nice but........
I'm a guy whose never run a lathe, and really have no idea about how everything works.........my mind is TOTALLY befuddled, doing mental gymnastics trying to figure out just how the $#*! you can turn a bowl with a handle stickin out a couple of inches!?!?!?!?
Of course, that's why I have you inlet my barrels too!!!!
Please put me out of my misery!  How do you do that????
Logged
In His grip,

Dane

cjarrett

  • Guest
Re: A couple of noggin's
« Reply #7 on: March 13, 2015, 05:53:12 AM »
Would love to see some "how to video's or pictures" on how you made these. They are beautiful pieces.
Logged

Offline David Rase

  • Hero Member
  • *****
  • Posts: 4320
  • If we need it here, make it here. Charlie Daniels
Re: A couple of noggin's
« Reply #8 on: March 13, 2015, 06:36:46 AM »
Quote from: smallpatch on March 13, 2015, 05:24:22 AM
Wow David,  nice but........
I'm a guy whose never run a lathe, and really have no idea about how everything works.........my mind is TOTALLY befuddled, doing mental gymnastics trying to figure out just how the $#*! you can turn a bowl with a handle stickin out a couple of inches!?!?!?!?
Of course, that's why I have you inlet my barrels too!!!!
Please put me out of my misery!  How do you do that????
Dane,
It's really not that hard. You just have to make sure your fingers, hands, elbows, arms and turning tools do not enter the plane of the handle radially outboard when the noggin is spinning.  Then, you just finish shaping and rounding all the wood in the "No fly zone"by hand.
David
Logged

Offline David Rase

  • Hero Member
  • *****
  • Posts: 4320
  • If we need it here, make it here. Charlie Daniels
Re: A couple of noggin's
« Reply #9 on: March 13, 2015, 06:40:56 AM »
Quote from: cjarrett on March 13, 2015, 05:53:12 AM
Would love to see some "how to video's or pictures" on how you made these. They are beautiful pieces.
I almost took pictures of the process when I was tuning the third noggin.  I am going to try and get my hands on some burl this weekend.  If I do, I will do another noggin and document the process for a tutorial.  If I do not get to it next week, it will be another month before I get back to the lathe.
David
Logged

Offline The Original Griz

  • Sr. Member
  • ****
  • Posts: 444
Re: A couple of noggin's
« Reply #10 on: March 13, 2015, 12:05:09 PM »
Quote from: smallpatch on March 13, 2015, 05:24:22 AM
Wow David,  nice but........
I'm a guy whose never run a lathe, and really have no idea about how everything works.........my mind is TOTALLY befuddled, doing mental gymnastics trying to figure out just how the $#*! you can turn a bowl with a handle stickin out a couple of inches!?!?!?!?
Of course, that's why I have you inlet my barrels too!!!!
Please put me out of my misery!  How do you do that????

if that scares ya, you oughta watch me turn the threaded end of a horn... Dave thems some darn fine noggins. Great work, as always
Logged
“I predict future happiness for Americans if they can prevent the government from wasting the labors of the people under the pretense of taking care of them.”
Thomas Jefferson
www.timsannerpowderhorns.com

Offline Tim Crosby

  • Administrator
  • Hero Member
  • *
  • Posts: 18391
  • AKA TimBuckII
Re: A couple of noggin's
« Reply #11 on: March 13, 2015, 04:28:18 PM »
 You did a really nice job on those Dave. Defiantly need to keep your mind on what your doing.

  Tim C.
Logged

Offline bob in the woods

  • Hero Member
  • *****
  • Posts: 4555
Re: A couple of noggin's
« Reply #12 on: March 13, 2015, 06:29:54 PM »
Very nice .   That would be a couple of weeks work for my crooked knife  ;D
Logged

VALongrifle

  • Guest
Re: A couple of noggin's
« Reply #13 on: March 14, 2015, 08:29:01 AM »
Really nice work...been looking for a noggin for quite a bit.  From what I've found, you'd corner the market.  I'd buy a couple right off the bat!

Pat

Logged

Horner75

  • Guest
Re: A couple of noggin's
« Reply #14 on: March 16, 2015, 05:32:49 PM »
Dave,  Glad to see your getting your monies worth out of that new lathe. __ really nice noggins!

Rick
Logged
Pages: [1]   Go Up
« previous next »