« previous next »
Pages: [1]   Go Down

Author Topic: Wood Inlay  (Read 3033 times)

Offline Old Ford2

  • Hero Member
  • *****
  • Posts: 1102
Wood Inlay
« on: March 28, 2017, 05:32:15 AM »
Hi,
I am about to install a black wood ( not ebony??) inlay on a cheek piece.
What is the best glue or epoxy?
Thank you!
Fred
Logged
Never surrender, always take a few with you.
Let the Lord pick the good from the bad!

Offline Longshot

  • Sr. Member
  • ****
  • Posts: 324
Re: Wood Inlay
« Reply #1 on: March 28, 2017, 01:23:36 PM »
I've used Titebond II and III to set set numerous wood inlays, without issue.  Be sure to clean all glue overrun from inlay and adjacent areas thoroughly  with a damp cloth.  Also, if the inlay is cut from any of the resinous, exotic type woods, wipe down the bonding surface with mineral spirits and let dry before setting.
Logged

Offline Old Ford2

  • Hero Member
  • *****
  • Posts: 1102
Re: Wood Inlay
« Reply #2 on: March 28, 2017, 04:02:32 PM »
Hi,
Thank you for the quick reply!
Fred
Logged
Never surrender, always take a few with you.
Let the Lord pick the good from the bad!

Offline L. Akers

  • Hero Member
  • *****
  • Posts: 509
Re: Wood Inlay
« Reply #3 on: March 28, 2017, 04:22:42 PM »
Ditto on the Titebond glue.  I don't wipe the squeeze-out off but allow the glue to set a couple of hours then use a scraper to remove it.  Wiping the glue, even with a wet cloth, can cause stain acceptance problems in the wiped area.
Logged

Offline Jay Close

  • Full Member
  • ***
  • Posts: 104
Re: Wood Inlay
« Reply #4 on: March 28, 2017, 04:37:52 PM »
There is an epoxy especially formulated to glue oily, exotic hardwoods and to adhere dissimilar materials. It's called "G-Flex", available online.
Logged

Offline deepcreekdale

  • Hero Member
  • *****
  • Posts: 641
Re: Wood Inlay
« Reply #5 on: March 28, 2017, 08:17:51 PM »
I am one of the Titebond III guys. Handled correctly it is stronger than the wood and dries quickly. Epoxy is great, I just don't like to mess around with mixing, waiting for it to set etc.
Logged
”Far and away the best prize that life has to offer is the chance to work hard at work worth doing.” Theodore Roosevelt

Offline Robby

  • Hero Member
  • *****
  • Posts: 2656
  • NYSSR ―
Re: Wood Inlay
« Reply #6 on: March 28, 2017, 08:43:52 PM »
I have glued a few ebony inlays to maple. I wiped down the ebony with acetone and used Titebond II. Its been several years and their still hanging tough.
Robby
Logged
molon labe
We the people are the rightful masters of both Congress and the courts, not to overthrow the Constitution but to overthrow the men who pervert the Constitution. A. Lincoln

Offline Old Ford2

  • Hero Member
  • *****
  • Posts: 1102
Re: Wood Inlay
« Reply #7 on: March 28, 2017, 09:14:06 PM »
I was thinking of wiping with acetone, to remove any oils, but thank you for the confirmation.
Fred
Logged
Never surrender, always take a few with you.
Let the Lord pick the good from the bad!

Offline Hungry Horse

  • Hero Member
  • *****
  • Posts: 5565
Re: Wood Inlay
« Reply #8 on: March 28, 2017, 10:07:08 PM »
Wood inlays were seen a lot on jaeger rifles, but were very rare on American guns.

  Hungry Horse
Logged

Offline frogwalking

  • Hero Member
  • *****
  • Posts: 1044
Re: Wood Inlay
« Reply #9 on: March 28, 2017, 11:10:06 PM »
I once glued hundreds of teak "boards" 1/4 inch thick to the fiberglass cabin sole of a sailboat.  I wiped the teak pieces with acetone and glued with epoxy.  That was almost 30 years ago.  I saw the boat 4 years ago, and the teak cabin sole still looks good.
Logged
Quality, schedule, price; Pick any two.

Offline smylee grouch

  • Hero Member
  • *****
  • Posts: 7912
Re: Wood Inlay
« Reply #10 on: March 29, 2017, 12:02:18 AM »
I think it was in one of Shumways books that I seen pictures of a Jacob Kuntz rifle that had wood inlays on it.
Logged
Pages: [1]   Go Up
« previous next »