« previous next »
Pages: [1]   Go Down

Author Topic: Is this a tool/template used in lock making?  (Read 4052 times)

Offline PPatch

  • Hero Member
  • *****
  • Posts: 2456
Is this a tool/template used in lock making?
« on: April 05, 2017, 07:04:00 PM »



fb photo upload

Do any of you know what it is/was used for?

Thanks

dave
Logged
Dave Parks   /   Quis custodiet ipsos custodes?

Offline Curtis

  • Hero Member
  • *****
  • Posts: 2338
  • Missouri
Re: Is this a tool/template used in lock making?
« Reply #1 on: April 05, 2017, 07:16:33 PM »
Looks like a tool used for finding percussion hammer throw and orientation to me.

Curtis
Logged
Curtis Allinson
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Sometimes, late at night when I am alone in the inner sanctum of my workshop and no one else can see, I sand things using only my fingers for backing

Offline Hungry Horse

  • Hero Member
  • *****
  • Posts: 5565
Re: Is this a tool/template used in lock making?
« Reply #2 on: April 05, 2017, 07:23:21 PM »
Yep, it measures the throw, and indexes the orientation of the tumbler. Very cool.

  Hungry Horse
Logged

Offline P.W.Berkuta

  • Hero Member
  • *****
  • Posts: 2213
Re: Is this a tool/template used in lock making?
« Reply #3 on: April 05, 2017, 07:31:28 PM »
Yes indeed -- it is VERY cool ;) I wish I had seen that tool 40+ years ago would have been a good tool to have. I've got along with a ruler and my eye ball since I've started this hobby!
Logged
"The person who says it cannot be done should not interrupt the person who is doing it." - Chinese proverb

Offline PPatch

  • Hero Member
  • *****
  • Posts: 2456
Re: Is this a tool/template used in lock making?
« Reply #4 on: April 05, 2017, 08:12:21 PM »
Thanks guys, now I know...

dave
Logged
Dave Parks   /   Quis custodiet ipsos custodes?

Offline Daryl

  • Hero Member
  • *****
  • Posts: 15825
Re: Is this a tool/template used in lock making?
« Reply #5 on: April 05, 2017, 08:44:13 PM »
The angle for the nipple seat is adjustable to get the correct angle for the hammer nose to strike at 90 degrees, I assume, so the filer can get that right. Cool Tool!
Logged
Daryl

"a gun without hammers is like a spaniel without ears" King George V

Offline Don Stith

  • Hero Member
  • *****
  • Posts: 2815
Re: Is this a tool/template used in lock making?
« Reply #6 on: April 05, 2017, 10:59:05 PM »
I used them to orient the nipple on a drum to be sure it fit the hammer.
Logged

Offline snapper

  • Hero Member
  • *****
  • Posts: 2432
Re: Is this a tool/template used in lock making?
« Reply #7 on: April 05, 2017, 11:08:02 PM »
I am making an assumption that my friend and fellow long range ML shooter Karl Kuehn might of made this tool.
If you want, I can send him an email.

I just saw him a couple of weeks ago at Oakridge shoot.

fleener
Logged
My taste are simple:  I am easily satisfied with the best.  Winston Churchill

Offline Mike Brooks

  • Hero Member
  • *****
  • Posts: 13415
    • Mike Brooks Gunmaker
Re: Is this a tool/template used in lock making?
« Reply #8 on: April 05, 2017, 11:11:05 PM »
I use one in place of a caliper..... :P
Logged
NEW WEBSITE! www.mikebrooksflintlocks.com
Say, any of you boys smithies? Or, if not smithies per se, were you otherwise trained in the metallurgic arts before straitened circumstances forced you into a life of aimless wanderin'?

Offline Ky-Flinter

  • Global Moderator
  • Hero Member
  • *
  • Posts: 7496
  • Born in Kentucke, just 250 years late
Re: Is this a tool/template used in lock making?
« Reply #9 on: April 05, 2017, 11:13:35 PM »
That's handy-er than pockets on a shirt!

-Ron
Logged
Ron Winfield

Life is too short to hunt with an ugly gun. -Nate McKenzie

ron w

  • Guest
Re: Is this a tool/template used in lock making?
« Reply #10 on: April 06, 2017, 06:48:50 PM »
looks like something that might be used to locate the full cock notch on a tumbler.
Logged

Stonebreaker

  • Guest
Re: Is this a tool/template used in lock making?
« Reply #11 on: April 07, 2017, 12:25:16 AM »
Quote from: snapper on April 05, 2017, 11:08:02 PM
I am making an assumption that my friend and fellow long range ML shooter Karl Kuehn might of made this tool.
If you want, I can send him an email.
I just saw him a couple of weeks ago at Oakridge shoot.
fleener

Could you please ask him what he calls this tool, and how much he sells them for? I'm looking for a tool name that will lead to finding more of these on the web. Thanks
Logged

Offline smallpatch

  • Hero Member
  • *****
  • Posts: 4107
  • Dane Lund
Re: Is this a tool/template used in lock making?
« Reply #12 on: April 07, 2017, 08:59:12 AM »
Mr Brooks,
You are an absolute hoot!
Logged
In His grip,

Dane

Offline Mike Brooks

  • Hero Member
  • *****
  • Posts: 13415
    • Mike Brooks Gunmaker
Re: Is this a tool/template used in lock making?
« Reply #13 on: April 07, 2017, 01:41:40 PM »
Quote from: smallpatch on April 07, 2017, 08:59:12 AM
Mr Brooks,
You are an absolute hoot!
That gizmo looks like a far more useful tool than a caliper if you're making ML's.
Logged
NEW WEBSITE! www.mikebrooksflintlocks.com
Say, any of you boys smithies? Or, if not smithies per se, were you otherwise trained in the metallurgic arts before straitened circumstances forced you into a life of aimless wanderin'?
Pages: [1]   Go Up
« previous next »