AmericanLongRifles Forums
Welcome,
Guest
. Please
login
or
register
.
1 Hour
1 Day
1 Week
1 Month
Forever
Login with username, password and session length
News:
Home
Help
Login
Register
AmericanLongRifles Forums
»
General discussion
»
Contemporary Accoutrements
»
To Horn Or Not To Horn?
« previous
next »
Print
Pages: [
1
]
Go Down
Author
Topic: To Horn Or Not To Horn? (Read 1355 times)
macr0w
Guest
To Horn Or Not To Horn?
«
on:
May 06, 2021, 05:36:50 PM »
This old friend of mine gave me this horn the other day.
I was thinking about making something out of it.
It has a fair amount of curl to it. Is it too curly to make a powder horn out of?
Do guys prefer a straighter horn to carry?
I know a little curl is typical but this one hooks pretty good.
Let me know what you think about it.
Logged
J Henry
Hero Member
Posts: 685
Re: To Horn Or Not To Horn?
«
Reply #1 on:
May 06, 2021, 05:49:45 PM »
If my friend gave it to me,, I wouldn't care if it were a corkscrew,I'd be making it into a powder horn.I have several steer horns that have a lot more twist, unique and going into powder horn.
Logged
D. Taylor Sapergia
Member 3
Hero Member
Posts: 12671
Re: To Horn Or Not To Horn?
«
Reply #2 on:
May 06, 2021, 07:01:16 PM »
I'd push a length of 1/16" welding rod down the outside curve of the horn to determine where the hollow part ends and the solid tip begins. Mark that on the outside of the horn and determine if you can run a drill bit into the tip to intersect the hollow part. That will also tell you how much of the tip to cut off in order to facilitate that drilling.
It'll likely make a nice powder horn.
Logged
D. Taylor Sapergia
www.sapergia.blogspot.com
Art is not an object. It is the excitement inspired by the object.
macr0w
Guest
Re: To Horn Or Not To Horn?
«
Reply #3 on:
May 06, 2021, 07:11:24 PM »
Yeah, it is a cool looking horn.
I was trying to decide on making it into a powder horn or something else.
If it was too curvy for a powder horn I was going to think about making something else.
We'll see how this goes.
I still haven't finished the powder horn my girl bought for me.
Logged
MuskratMike
Hero Member
Posts: 2260
Re: To Horn Or Not To Horn?
«
Reply #4 on:
May 06, 2021, 07:25:28 PM »
You bet that will make a fine horn and a great way to remember and thank your friend.
Logged
"Muskrat" Mike McGuire
Keep your eyes on the skyline, your flint sharp and powder dry.
smylee grouch
Hero Member
Posts: 7907
Re: To Horn Or Not To Horn?
«
Reply #5 on:
May 07, 2021, 02:49:56 AM »
Would a horn with that much curve make a good blowing or "Hunt" horn?
Logged
Tim Crosby
Administrator
Hero Member
Posts: 18385
AKA TimBuckII
Re: To Horn Or Not To Horn?
«
Reply #6 on:
May 07, 2021, 12:18:19 PM »
I don't know about a powder horn it would have to be turned quite a bit to get powder out. Would make a good Hunting horn I would think depending on the cavity. May need to see a couple of other shots.
Tim C.
Logged
macr0w
Guest
Re: To Horn Or Not To Horn?
«
Reply #7 on:
May 08, 2021, 02:11:26 AM »
Here's a couple of extra pics.
I was trying to think if I didn't make a powder horn what would I make?
A chalice maybe?
You can see by my wire how deep it is.
Logged
Tim Crosby
Administrator
Hero Member
Posts: 18385
AKA TimBuckII
Re: To Horn Or Not To Horn?
«
Reply #8 on:
May 08, 2021, 03:44:04 PM »
Your thumb in the pic looks to be almost life size I would cut the tip off just about its width. Put a mark on the horn just were the end of the wire is and one in the cut off section that makes a straight line with it and drill with a 2/4" bit. Going slowly just a little at a time to help clean out the curls. Make sure you have the horn braced up tight. I still think it would make a nice blowing horn, especially with that large bugle like end.
Tim C.
Logged
Print
Pages: [
1
]
Go Up
« previous
next »
AmericanLongRifles Forums
»
General discussion
»
Contemporary Accoutrements
»
To Horn Or Not To Horn?