« previous next »
Pages: [1]   Go Down

Author Topic: Vent liner placement ?  (Read 4174 times)

Offline Skychief

  • Hero Member
  • *****
  • Posts: 650
Vent liner placement ?
« on: June 16, 2011, 05:06:47 AM »
How do you all locate your vent liners?

 Do you make sure that the edge (arc) of the liner misses the end of the breech plug?

-Or-

Do you drill the liner to "hit" the breech plug so that the vent is as close to the breech plug face as possible?

Is one better than the other in terms of ignition or other areas I may not be thinking of?


I have little experience with building, but, am jumping in with both feet, so, I appreciate your thoughts and the pros and cons where placement of the vent liner in relation to the breech plug is concerned.

Thanks, Skychief.
Logged

Offline Acer Saccharum

  • Administrator
  • Hero Member
  • *
  • Posts: 19311
    • Thomas A Curran
Re: Vent liner placement ?
« Reply #1 on: June 16, 2011, 05:31:31 AM »
I like to place the liner so that the thread diameter just misses the face of the plug. This means I can unscrew the plug without having to remove/drill out the liner first.

I try to center the liner in the side flat, top to bottom.

I have lately started to use Tom Snyder's inside coning tools, which have been very satisfactory, especially in getting the touchhole a little closer to the plug. Properly done, the gun performs much as if it had a touchhole liner installed. Eventually the hole will erode, so at that time it can be lined, eh.

Tom
Logged
Tom Curran's web site : http://monstermachineshop.net
Ramrod scrapers are all sold out.

Offline Skychief

  • Hero Member
  • *****
  • Posts: 650
Re: Vent liner placement ?
« Reply #2 on: June 17, 2011, 05:44:58 AM »
Thanks for the reply 'Sugar Maple'. ;)   I wonder if most builders do as you?  

Much appreciated, Skychief.
« Last Edit: June 17, 2011, 05:45:46 AM by Skychief »
Logged

Offline bgf

  • Hero Member
  • *****
  • Posts: 1403
Re: Vent liner placement ?
« Reply #3 on: June 17, 2011, 06:47:25 AM »
I did it the same way, but added a little extra space for a bigger liner in case of an "oops".  Seems to work like it should, and I haven't had any fouling problems due to that additional clearance as far as I can tell -- even allocating for a 3/8" liner (I used a 1/4"), it's only an extra sixteenth of an inch; using a 1/4" liner and allowing for 5/16" would only be 1/32" difference.
Logged

Offline Don Getz

  • Hero Member
  • *****
  • Posts: 6853
Re: Vent liner placement ?
« Reply #4 on: June 17, 2011, 03:20:23 PM »
I prefer to use the method Tom described above.    Have the threads of the liner just touch the front of the breechplug
face.  By doing this you don't have to file a groove in the front of the plug, which becomes one of those areas that is more
difficult to clean.   Determine where the touchhole will be before you inlet the lock.   Do not be concerned about whether
or not the fence of the lock is even with the breech end of the barrel.   Some will say this must be done......poppycock.
Don
Logged

Offline Long John

  • Hero Member
  • *****
  • Posts: 1618
  • Give me Liberty or give me Death
Re: Vent liner placement ?
« Reply #5 on: June 17, 2011, 04:47:30 PM »
I do it like Acer and Don.  I just don't do it quit as well!

Best Regards,

JMC
Logged

Offline Dr. Tim-Boone

  • Global Moderator
  • Hero Member
  • *
  • Posts: 6538
  • I Like this hat!!
Re: Vent liner placement ?
« Reply #6 on: June 17, 2011, 04:47:53 PM »
What Don, bgf  and Acer said!!
Logged
De Oppresso Liber
Marietta, GA

Liberty is the only thing you cannot have unless you are willing to give it to others. – William Allen White

Learning is not compulsory...........neither is survival! - W. Edwards Deming

Offline Skychief

  • Hero Member
  • *****
  • Posts: 650
Re: Vent liner placement ?
« Reply #7 on: June 17, 2011, 04:56:12 PM »
Thanks for the information all.  It is really appreciated.

Skychief
Logged

Birdhunter

  • Guest
Re: Vent liner placement ?
« Reply #8 on: June 17, 2011, 07:10:48 PM »
Skychief,
I also just mark placement of the touchhole liner, then inlet the lockplate & then drill  & tap.
Curt
Logged

Offline Skychief

  • Hero Member
  • *****
  • Posts: 650
Re: Vent liner placement ?
« Reply #9 on: June 17, 2011, 11:25:40 PM »
Curt, do you miss the breech plug as well with the liner?

Thanks, Skychief
Logged

Birdhunter

  • Guest
Re: Vent liner placement ?
« Reply #10 on: June 18, 2011, 05:02:55 PM »
Yes, just like the others do.
Curt
Logged
Pages: [1]   Go Up
« previous next »