« previous next »
Pages: [1]   Go Down

Author Topic: First time carving- work in progress  (Read 3939 times)

Offline James

  • Hero Member
  • *****
  • Posts: 627
First time carving- work in progress
« on: October 07, 2011, 02:57:32 AM »
I had intended to skip the carving on my first gun as I had never done any. I changed my mind and this is where I'm at, still have a lot to clean up, but it is supposed to resemble #82 in Kindig's "Thoughts on the Kentucky Rifle..."






Logged
"Guard with jealous attention the public liberty. Suspect everyone who approaches that jewel. Unfortunately, nothing will preserve it but downright force. Whenever you give up that force, you are ruined... The great object is that every man be armed. Everyone who is able might have a gun." P.Henry

sleddman

  • Guest
Re: First time carving- work in progress
« Reply #1 on: October 07, 2011, 03:29:44 AM »
Liked the photos of your work.  Nice going
Logged

Offline draken

  • Sr. Member
  • ****
  • Posts: 404
Re: First time carving- work in progress
« Reply #2 on: October 07, 2011, 03:52:01 AM »
I don't have the book for comparison, but I'd say that's darned good for your first try.
Logged
Dick 

Times have sure changed. Gun control used to mean keeping the muzzle pointed in a safe direction

Never write a check with your mouth that your butt can't cash!

Offline alyce-james

  • Hero Member
  • *****
  • Posts: 909
Re: First time carving- work in progress
« Reply #3 on: October 07, 2011, 04:16:11 AM »
The work I see in the pictures tell me you made a wise decision to go ahead and add the carving to your first build. Practice blocks before final attempt will also benefit. Take your time, use very sharp tools, after cleanup and final stain you will be surprised. Aj 
Logged
"Candy is Dandy but Liquor is Quicker". by Poet Ogden Nash 1931.

Offline rich pierce

  • Administrator
  • Hero Member
  • *
  • Posts: 19522
Re: First time carving- work in progress
« Reply #4 on: October 07, 2011, 04:16:48 PM »
You've got a good design, good as many originals.  And you can carve.  I have always been surprised how low most of the carving from that period was.  So you might want to see if you can achieve the same visual effect with less height.
Logged
Andover, Vermont

Offline Lucky R A

  • Hero Member
  • *****
  • Posts: 1628
  • In Costume
Re: First time carving- work in progress
« Reply #5 on: October 07, 2011, 05:06:00 PM »
       Looks like you are off to a very good start.  I have seen a lot of first carvings that didn't come close to the quality of your work.  Rich is correct, most original carving is rather shallow.  The illusion of greater depth is usually achieved by slightly undercutting the edges that define the pattern. 
        One tip, keep the butt plate on your rifle when you are carving and working on it.  One drop of the gun that breaks the toe or the heel will cause you to use words that you shouldn't.   
Logged
"The highest reward that God gives us for good work is the ability to do better work."  - Elbert Hubbard

greybeard

  • Guest
Re: First time carving- work in progress
« Reply #6 on: October 07, 2011, 06:37:36 PM »
Very nice  for a first effort. i agree with the butplate thingy.  Just wait till it's stained.  Bob
Logged

Offline James

  • Hero Member
  • *****
  • Posts: 627
Re: First time carving- work in progress
« Reply #7 on: October 07, 2011, 07:09:09 PM »
Thank you for the input. I didn't realize 1/32" could seem so tall. I have, much to my wife and children's dismay, cut the height back and will post when I have it detailed again. Thanks, Jim
Logged
"Guard with jealous attention the public liberty. Suspect everyone who approaches that jewel. Unfortunately, nothing will preserve it but downright force. Whenever you give up that force, you are ruined... The great object is that every man be armed. Everyone who is able might have a gun." P.Henry
Pages: [1]   Go Up
« previous next »