Author Topic: Help Identify this Rifle, please  (Read 3893 times)

hawknknife

  • Guest
Help Identify this Rifle, please
« on: January 14, 2012, 09:54:40 PM »
This small bore percussion rifle was purchased from an elderly gentleman this weekend.  I need help about age and value if possible. 

The caliber is .30 to .32 and the bore is about mirror bright with 6 lands and 6 grooves.  The barrel length is 28 inches, has a patent hooked breach, and is very weekly marked on the side flat "AL-------------K  Worcester".  The rifle's engraved lock is marked, "Bell, London" and overall it appears to be in excellent condition.  I noticed an unusual feature in that there is a set trigger screw in the side of the lock and the lock has a two click tumbler.  The pull is 13 inches and the barrel is 7/8th inch at the muzzle.

Can anyone tell me any details on this rifle? I would greatly appreciate it.
Thanks
Carl
http://www.hawknknife.com
hawknknife@hotmail.com















Offline Curt J

  • member 2
  • Hero Member
  • ****
  • Posts: 1521
Re: Help Identify this Rifle, please
« Reply #1 on: January 15, 2012, 01:39:05 AM »
What a cute little rifle!  I believe the maker's name is ALLEN & WHEELOCK, WORCESTER (Massachusetts).

Offline JTR

  • member 2
  • Hero Member
  • ****
  • Posts: 4351
Re: Help Identify this Rifle, please
« Reply #2 on: January 15, 2012, 05:04:35 AM »
The name looks like it could read Allen & Wheelock to me also.
Allen & Wheelock was a partnership with Ethan Allen firearms from 1856 to 1865, according to the 9th edition of Flaydermans Guide, although it doesn't show a picture of anything quite like yours.
John
John Robbins

Offline halfstock

  • Full Member
  • ***
  • Posts: 135
Re: Help Identify this Rifle, please
« Reply #3 on: January 15, 2012, 10:07:39 PM »
I would suggest that you should look toward england for a maker.

Offline Hudnut

  • Full Member
  • ***
  • Posts: 231
Re: Help Identify this Rifle, please
« Reply #4 on: January 15, 2012, 11:44:30 PM »
Can't see an A&W barrel being on an English rifle.  There were a lot of English locks used on guns this side of the pond, though.
Might be an A&W barrel which was used by a gunmaker, rather than this being an A&W rifle.
Attractive, tidy rifle.  Years ago, I saw another small bore, ribless rifle, with the rod set in a groove on the bottom flat.  Not a common feature.

Offline Bob Roller

  • Hero Member
  • *****
  • Posts: 9687
Re: Help Identify this Rifle, please
« Reply #5 on: January 16, 2012, 12:13:40 AM »
E.M.Farris,one of the mainsprings in the start up of the NMLRA had a fine George Ferris match rifle with a groove in the bottom flat of the barrel and it too was turned for a starter.
It was 38 caliber with a Remington Cast Steel barrel and I used  it in indoor shoots we had in the National Guard Armory in Portsmouth,Ohio and won several bushel baskets of groceries with it. The rule for indoor shoots was nothing bigger than a 40 caliber with no more than 40 grains of powder. I hope whoever has this fine rifle knows what it is and appreciates it.

Bob Roller

Offline smokinbuck

  • Hero Member
  • *****
  • Posts: 3004
Re: Help Identify this Rifle, please
« Reply #6 on: January 16, 2012, 12:53:55 AM »
hawknknife,
I believe Bob has gont this one pegged. Round muzzle would not need to be turned for a starter but the butt plate and screw hole for an aperture tang sight says target to me.
Mark Probably a Remington barrel.
Mark

Offline Sequatchie Rifle

  • Global Moderator
  • Hero Member
  • *
  • Posts: 978
  • F. & A.M. Helion #1; 3rd SFG(ABN)
Re: Help Identify this Rifle, please
« Reply #7 on: January 16, 2012, 05:39:15 AM »
The trigger guard reminds me of Silas Allen of Mass.
"We fight not for glory, nor riches nor honors, but for freedom alone, which no good man gives up except with his life.” Declaration of Arbroath, 1320