AmericanLongRifles Forums
Welcome,
Guest
. Please
login
or
register
.
1 Hour
1 Day
1 Week
1 Month
Forever
Login with username, password and session length
News:
Home
Help
Login
Register
AmericanLongRifles Forums
»
General discussion
»
Gun Building
»
Brass barreled pistol
« previous
next »
Print
Pages: [
1
]
Go Down
Author
Topic: Brass barreled pistol (Read 3791 times)
cmac
Hero Member
Posts: 695
Brass barreled pistol
«
on:
May 31, 2013, 02:13:50 AM »
Still much to do on this one, but I feel the "worst" is over. The butt cap was the hardest thing I have ever made and inlet. I have done 3 now but this tear drop one was by far the hardest. Barrel maker unknown. Russ Hamm lock. Also a hard piece of walnut to carve. The grain runs every which way!
«
Last Edit: June 05, 2013, 07:40:31 PM by rich pierce
»
Logged
cheyenne
Guest
Re: Brass barreled pistol in the works
«
Reply #1 on:
June 02, 2013, 07:18:50 PM »
Looking good!
Logged
Curtis
Hero Member
Posts: 2335
Missouri
Re: Brass barreled pistol in the works
«
Reply #2 on:
June 03, 2013, 07:09:50 AM »
Looks like it is coming along there, cmac. Tell us about the barrel, it's maker, etc. One thing I have a thought about, the wedding band could use some shaping. It may be a little far forward as well.
Curtis
Logged
Curtis Allinson
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Sometimes, late at night when I am alone in the inner sanctum of my workshop and no one else can see, I sand things using only my fingers for backing
James Wilson Everett
Hero Member
Posts: 1099
Re: Brass barreled pistol in the works
«
Reply #3 on:
June 03, 2013, 02:08:34 PM »
Guys,
This pistol is well on the way to being a real winner. One area that can be improved is the amount of wood that is below the lock and above the trigger guard. From the photo it looks like there is a good 3/8 or even 1/2 inch of wood showing beneath the bottom edge of the lock plate in the side view. This gives the wrist area a bit of a chubby look. However, there is a really easy way to put the stock on a diet!
Drill a hole upwards in the front inlet of the trigger guard into the ramrod hole to see how much extra wood there is here. Then remove the wood from the bottom of the stock in the wrist or belly area. You can probably remove about 1/4 inch or so here and make the stock a good bit slimmer. Re-inlet that beautiful trigger guard and the job is done. Sometimes on original guns the ramrod actually touches the top surface of the trigger guard metal in this inlet with almost no extra wood here. I am sure that you will be pleased with the result.
Here is a photo of brass barreled pistols, see the much smaller wood dimension below the lock and above the trigger guard?
Jim
«
Last Edit: December 04, 2019, 03:47:36 AM by James Wilson Everett
»
Logged
cmac
Hero Member
Posts: 695
Re: Brass barreled pistol in the works
«
Reply #4 on:
June 03, 2013, 02:45:58 PM »
Thanks guys. I'm not sure of the barrel maker. It is unmarked and the owner didn't know either. It is a 45 caliber and 11" long. I would have removed more wood from the underside but I was getting close to the RR hole. The inletting/shaping and butt cap on this where a real pain. The grain runs every which way and swagging one of these caps out proved to be a challenge. The lock has had a lot of tuning and I had to straighten the lock plate as well. Gettin there
Logged
cmac
Hero Member
Posts: 695
Re: Brass barreled pistol
«
Reply #5 on:
June 05, 2013, 06:46:15 PM »
Brass 11",45 caliber smooth bore barrel(maker unknown), Russ Hamm lock, Muzzleloader Builder's Supply triggerguard and ramrod thimbles, walnut stock, handmade sideplate/belt hook, butt cap, and trigger. Silver star of David inlay.
«
Last Edit: June 05, 2013, 07:42:38 PM by rich pierce
»
Logged
Print
Pages: [
1
]
Go Up
« previous
next »
AmericanLongRifles Forums
»
General discussion
»
Gun Building
»
Brass barreled pistol