Author Topic: Thanks once again.  (Read 3104 times)

Offline Model19

  • Jr. Member
  • **
  • Posts: 71
  • Why read fiction, history is fascinating enough
Thanks once again.
« on: October 25, 2011, 02:09:49 AM »
Thanks for the barrel pin advice from my other post.  I got that taken care of today.  I just wanted to post a few observations as a complete newb to this hobby:
1) A vast amount of time is spent just looking at parts and how the thing looks as it sits in it's current state of progress.   Ponder, eyeball, ponder, read some more, look again.    I like that stuff
2) I started removing wood around the lock panels today.  Rasps, files, scraper, sand paper.... now it's starting to really look like a gun you'd want to own.  I referred back to #1 above and eyeballed and looked at pictures of old pieces after I had done a lot of the work around the panels.  I decided the panel curves needed to extend downwards more and the stock below the flats section of the barrel needed to be thinner and more sculpted, so I had at it. That was fun.  The actual shaping of the stock is really creative and rewarding.  I'm no expert, but I really enjoyed that and am happy with my progress so far.
3) Scrapers are cool!  I used old utility knife blades, and man, does that smooth stuff out.  My precarve had all kinds of machine marks that became visible  once I rubbed it with mineral spirits to see what kind of grain I have.  Almost all are gone now except for the butt.  Being a club butt, it has a big butt.   More work needed.
4) Rigging jigs and supports is fun too.  I have a 6' walnut board (left over from my kitchen counters) that I now use as a table extension on my drill press.  I also made one of those point jigs you use drilling the tang so you know where the drill will bust out.   I also mounted two wooden clamps to bases to serve as work holders. My benchtop has holes for stops and clamps and I use them to lock the bases down solidly while the fowler is in the homemade clamps.   

Again, thanks for the direct answers to my questions and for the hundreds of other answers/ideas I have gathered from reading old posts.    This place is a fantastic resource.

Geoff
Strawberry Banke, Greenland and Falmouth
Anthony Brackett's roots go deep

Offline Model19

  • Jr. Member
  • **
  • Posts: 71
  • Why read fiction, history is fascinating enough
Re: Thanks once again.
« Reply #1 on: June 10, 2013, 06:15:33 PM »
Figured I might as well show the end result.  I finished it in February, but have been reluctant to post a picture as I am still in awe of the quality of work I see here.  But what the heck.   
The premise was a fowling piece, perhaps passed on for a generation or two, indigenous to my families part of New England, meaning Boston and northwards.   Used, but not hammered on and neglected.  The Club Butt was the natural choice.  Simple fixtures.  Simple gun.  Same as they way they lived in the early 1700's up here.

And again, thanks for all the help, whether given directly to me or gathered from hours of perusal of this site.

Geoff
Strawberry Banke, Greenland and Falmouth
Anthony Brackett's roots go deep

Offline Captchee

  • Hero Member
  • *****
  • Posts: 768
Re: Thanks once again.
« Reply #2 on: June 11, 2013, 02:14:41 AM »
 looks pretty good from what i can see .

Offline KLMoors

  • Hero Member
  • *****
  • Posts: 859
Re: Thanks once again.
« Reply #3 on: June 11, 2013, 02:42:55 PM »
I agree. Nice lines from what I can see. Remember- lots of the work posted here is better looking than lots of the originals made back then!