« previous next »
Pages: [1]   Go Down

Author Topic: Trigger Guard Modified  (Read 2443 times)

n stephenson

  • Guest
Trigger Guard Modified
« on: January 02, 2018, 05:36:03 PM »
I am building a Danish flintlock rifle for a friend. It is based on an original in the back of the Shumway Jaeger book. I didn't have access to a guard like the original , and I have never cast brass before, so I took a Brown Bess guard and, whittled this one out as well as I could. It is not an exact copy but, it is a pretty good representation . I am posting this , to show those who haven't done it , that as long as you start out with enough "meat" , you can whittle out what your looking for , or as close as you can get without the ability to cast your own. Casting mounts IS on my bucket list by the way. Thanks Nate






multiple images upload
Logged

Offline Mike Brooks

  • Hero Member
  • *****
  • Posts: 13415
    • Mike Brooks Gunmaker
Re: Trigger Guard Modified
« Reply #1 on: January 02, 2018, 05:45:54 PM »
Nifty, I would never guess that started as a Bess guard. I hope you're charging accordingly. ;)
Logged
NEW WEBSITE! www.mikebrooksflintlocks.com
Say, any of you boys smithies? Or, if not smithies per se, were you otherwise trained in the metallurgic arts before straitened circumstances forced you into a life of aimless wanderin'?

n stephenson

  • Guest
Re: Trigger Guard Modified
« Reply #2 on: January 02, 2018, 06:13:12 PM »
Quote from: Mike Brooks on January 02, 2018, 05:45:54 PM
Nifty, I would never guess that started as a Bess guard. I hope you're charging accordingly. ;)
Against my better  judgment  Mike, I will admit that from start to finish this only took a little over 2 hours. I used my 4 1/2 inch grinder with a cutting wheel for the majority of the stock removal , this took about 15 minutes , the balance of the time was filing.
Logged

Offline James Rogers

  • Hero Member
  • *****
  • Posts: 3161
  • James Rogers
    • Fowling Piece
Re: Trigger Guard Modified
« Reply #3 on: January 02, 2018, 08:10:19 PM »
Looks good Nate! I have seen quite a fee earlier English pieces that looked to me to be fancied up guards from a standard military plate of the time.
Logged

Offline D. Taylor Sapergia

  • Member 3
  • Hero Member
  • *
  • Posts: 12664
Re: Trigger Guard Modified
« Reply #4 on: January 02, 2018, 08:12:58 PM »
Great work Nate.  Creating the furniture you need from what you have is always a neat project.
Logged
D. Taylor Sapergia
www.sapergia.blogspot.com

Art is not an object.  It is the excitement inspired by the object.

Offline Chowmi

  • Hero Member
  • *****
  • Posts: 843
Re: Trigger Guard Modified
« Reply #5 on: January 03, 2018, 08:15:43 AM »
Quote from: n stephenson on January 02, 2018, 06:13:12 PM
Quote from: Mike Brooks on January 02, 2018, 05:45:54 PM
Nifty, I would never guess that started as a Bess guard. I hope you're charging accordingly. ;)
Against my better  judgment  Mike, I will admit that from start to finish this only took a little over 2 hours. I used my 4 1/2 inch grinder with a cutting wheel for the majority of the stock removal , this took about 15 minutes , the balance of the time was filing.


And here's how I know I'm doing things wrong....
It takes me more than two hours to clean up a cast trigger guard, without doing any modifications.

Nice work Nate, never would have guessed that was a Bess guard.

Norm.
Logged
Cheers,
Chowmi

NMLRA
CLA

Offline BOB HILL

  • Hero Member
  • *****
  • Posts: 2281
Re: Trigger Guard Modified
« Reply #6 on: January 03, 2018, 08:23:23 AM »
Nice looking conversion, Nate. Like what you've done here.
Bob
Logged
South Carolina Lowcountry
Pages: [1]   Go Up
« previous next »