« previous next »
Pages: [1]   Go Down

Author Topic: muzzle cap question.  (Read 1135 times)

Offline Rt5403

  • Full Member
  • ***
  • Posts: 241
muzzle cap question.
« on: December 27, 2023, 05:28:20 AM »
Anyone know where I can get a muzzle cap like the following? It seems more slim and round than most production caps I've seen. And it doesn't seem to stick so far out on the sides like others I've seen.Toyed with making my own but not sure if I could pull it off.

Logged

Offline P.Bigham

  • Hero Member
  • *****
  • Posts: 596
Re: muzzle cap question.
« Reply #1 on: December 27, 2023, 06:49:00 AM »
Maybe Kiblers. Or make your own. It would depend on your barrel size at the muzzle cap.
« Last Edit: December 27, 2023, 06:57:37 AM by P.Bigham »
Logged
" not all who wander are lost"

Offline P.Bigham

  • Hero Member
  • *****
  • Posts: 596
Re: muzzle cap question.
« Reply #2 on: December 27, 2023, 06:54:59 AM »



Logged
" not all who wander are lost"

Offline Rt5403

  • Full Member
  • ***
  • Posts: 241
Re: muzzle cap question.
« Reply #3 on: December 27, 2023, 02:19:11 PM »
May try making my own. This one seems to not have a groove in the bottom either.
Logged

Offline Steeltrap

  • Hero Member
  • *****
  • Posts: 775
Re: muzzle cap question.
« Reply #4 on: December 27, 2023, 03:23:00 PM »
Check this out. Not all caps had the RR grove in them. https://americanlongrifles.org/forum/index.php?topic=62735.msg629100#msg629100
« Last Edit: December 27, 2023, 03:28:04 PM by Steeltrap »
Logged

Offline satwel

  • Sr. Member
  • ****
  • Posts: 257
Re: muzzle cap question.
« Reply #5 on: December 27, 2023, 05:40:13 PM »
Don't be afraid to try making your own muzzlecap. I just made one for an India Pattern Bess I restocked.

I followed this tutorial:  https://americanlongrifles.org/forum/index.php?topic=24785.0

I screwed up my first attempt, but my second try turned out perfectly. It was surprisingly easy. I built a paper template first to get the dimensions close to where they needed to be.
Logged

Offline Mike Brooks

  • Hero Member
  • *****
  • Posts: 13415
    • Mike Brooks Gunmaker
Re: muzzle cap question.
« Reply #6 on: December 27, 2023, 06:26:45 PM »
They aren't hard to make.
Logged
NEW WEBSITE! www.mikebrooksflintlocks.com
Say, any of you boys smithies? Or, if not smithies per se, were you otherwise trained in the metallurgic arts before straitened circumstances forced you into a life of aimless wanderin'?

Offline P.Bigham

  • Hero Member
  • *****
  • Posts: 596
Re: muzzle cap question.
« Reply #7 on: December 27, 2023, 11:43:20 PM »
Looking at the photo again it looks like there Is no cap on it simply wrapped around.
Logged
" not all who wander are lost"

Offline M. E. Pering

  • Sr. Member
  • ****
  • Posts: 273
Re: muzzle cap question.
« Reply #8 on: December 28, 2023, 01:08:59 AM »
Muzzle caps are pretty easy to make.  Make sure you start with annealed brass, and anneal again when needed.  I make mine from .040, but you could probably use .030 just as well.
Logged
Pages: [1]   Go Up
« previous next »