Author Topic: Hunting load poi on clean bore  (Read 438 times)

Offline HighUintas

  • Sr. Member
  • ****
  • Posts: 488
Hunting load poi on clean bore
« on: November 17, 2024, 08:57:38 AM »
I couldn't find much/any info on this in the search.

For a hunting load on a clean bore (specifically tow mink oil saturated on thick/tight patches) I'm wondering what everyone sees for their POI vs the POI of that same load when it is fouled. Is it vastly different?

How do you prepare your bore when loading for hunting?

I'll be testing this tomorrow. I swabbed the oil out of the bore, then patched it with acetone, then patched it with mink oil. I figured that might be the closest to a fouled bore condition. I'll fire my first shot as if I'm hunting, and hopefully it will be right on target.

Online Daryl

  • Hero Member
  • *****
  • Posts: 15813
Re: Hunting load poi on clean bore
« Reply #1 on: November 17, 2024, 11:18:43 AM »
Much depends on the calibre. My .69 hits the same POI whether second or first shot.
My .50 hits high with the first shot at 25 yards, however the second shot hits lower.
The .36 is reverse, with the first shot out of a clean bore hitting low, second and subsequent hitting higher.
Doesn't matter the lube used.
The use of acetone was not needed.
It will strike close enough for deer or any other game. Just sight the rifle for the first shot for hunting and learn where to hold for subsequent shots.
Daryl

"a gun without hammers is like a spaniel without ears" King George V

Offline Hawg

  • Full Member
  • ***
  • Posts: 105
Re: Hunting load poi on clean bore
« Reply #2 on: November 17, 2024, 11:38:43 AM »
I never fire a shot out of a clean bore. I fire a blank charge before I load it whether for hunting or plinking.

Online recurve

  • Hero Member
  • *****
  • Posts: 620
Re: Hunting load poi on clean bore
« Reply #3 on: November 17, 2024, 05:22:19 PM »





I have found clean shot are slightly higher 4 different rifles


« Last Edit: November 17, 2024, 05:28:16 PM by recurve »

Offline HighUintas

  • Sr. Member
  • ****
  • Posts: 488
Re: Hunting load poi on clean bore
« Reply #4 on: November 18, 2024, 03:19:56 AM »
I tested it today.

I wiped the bore with acetone and then ran a patch with me nk oil, then loaded a ball.

First shot was a touch high and left at 100yards. I swabbed the bore w a damp spit patch, then dry patch, then a mink oil patch then loaded the second round. It was a little low and left. I repeated that process and the third round was a little high and centered. I then just loaded as I usually do, not swabbing, and shot quite a few more shots. They were all in the same area surrounding the bull, so I don't think there is a difference in my poi on a clean bore that my shooting ability is able to detect.

I had a couple of flinches in there... The ones very wide left/right. Other than that, I had a little trouble sighting accurately on this target. I was shooting at sunrise and the target was hidden in the shadow of the range berm. With different lighting conditions, I think I could improve that quite a bit



« Last Edit: November 18, 2024, 06:19:22 AM by HighUintas »

Online Daryl

  • Hero Member
  • *****
  • Posts: 15813
Re: Hunting load poi on clean bore
« Reply #5 on: November 18, 2024, 05:29:01 AM »
It appears your rifle cares not one bit.
Daryl

"a gun without hammers is like a spaniel without ears" King George V

Offline D. Taylor Sapergia

  • Member 3
  • Hero Member
  • *
  • Posts: 12671
Re: Hunting load poi on clean bore
« Reply #6 on: November 18, 2024, 11:37:37 PM »
None of my rifles change their poi from first to subsequent shots.  In fact, when I go to a match, often the first shot on the trail is the tie breaker shot.  It is normally at fairly close range, ie:  15 to 20 yards, and is almost always a dot about 5/8" diameter surrounded by scoring rings.  In the matches in which I participate, if you don't punch out the centre dot, you will not win the day.  And I shoot at mine with a clean bore knowing that where the sights lay there too will lay the ball.  My BPCR's are a different animal.
D. Taylor Sapergia
www.sapergia.blogspot.com

Art is not an object.  It is the excitement inspired by the object.

Online MuskratMike

  • Hero Member
  • *****
  • Posts: 2260
Re: Hunting load poi on clean bore
« Reply #7 on: November 19, 2024, 01:46:01 AM »
Not sure about this wiping the bore with acetone? Before I go out shooting or hunting I do wipe the bore with Isopropyl alcohol to remove any residual oil from the barrel that may have remained at the last cleaning. the acetone probably will do the same but is a whole lot more money. Any one else use acetone on a regular basis? Been in this game for 50 years and have never heard of it.
"Muskrat" Mike McGuire
Keep your eyes on the skyline, your flint sharp and powder dry.

Offline HighUintas

  • Sr. Member
  • ****
  • Posts: 488
Re: Hunting load poi on clean bore
« Reply #8 on: November 19, 2024, 01:52:26 AM »
Not sure about this wiping the bore with acetone? Before I go out shooting or hunting I do wipe the bore with Isopropyl alcohol to remove any residual oil from the barrel that may have remained at the last cleaning. the acetone probably will do the same but is a whole lot more money. Any one else use acetone on a regular basis? Been in this game for 50 years and have never heard of it.

I have acetone in my garage that I typically use for degreasing small metal parts. There is no particular reason I use it over iso other than it's in my garage and the iso isn't!

The amount I use on a patch it's still super cheap

Online Daryl

  • Hero Member
  • *****
  • Posts: 15813
Re: Hunting load poi on clean bore
« Reply #9 on: November 19, 2024, 03:09:16 AM »
I have never head of using acetone. Now and then, I will run a dry patch down and out before loading That doesn't happen often.
Daryl

"a gun without hammers is like a spaniel without ears" King George V