« previous next »
Pages: [1]   Go Down

Author Topic: Mike Brooks: C'mon, tell us how ya did it!  (Read 7459 times)

Offline Ky-Flinter

  • Global Moderator
  • Hero Member
  • *
  • Posts: 7500
  • Born in Kentucke, just 250 years late
Mike Brooks: C'mon, tell us how ya did it!
« on: February 15, 2010, 05:11:24 PM »
« Last Edit: May 13, 2020, 11:40:49 PM by Ky-Flinter »
Logged
Ron Winfield

Life is too short to hunt with an ugly gun. -Nate McKenzie

Offline Mike Brooks

  • Hero Member
  • *****
  • Posts: 13415
    • Mike Brooks Gunmaker
Re: Mike Brooks: C'mon, tell us how ya did it!
« Reply #1 on: February 15, 2010, 06:00:32 PM »
No big deal man, it's just patches glued in. Lots of time and beer is all. ;D I got that stock out of a sawmills slab pile 20 years ago when I was picking up a truck load of slabs for fire wood.. It was probably  24" wide and 12' long and 3" thick. It probably weighed hundreds of pounds.  It had termite damage through out, but I probably got 5 full stocks out of it with no termite damage and this little short stock. There was only one termite hole in the end grain of the buttstock so I figured "what the $#*!" and made this gun out of it. As you can see I ran into a little more than one termite hole.....
Logged
NEW WEBSITE! www.mikebrooksflintlocks.com
Say, any of you boys smithies? Or, if not smithies per se, were you otherwise trained in the metallurgic arts before straitened circumstances forced you into a life of aimless wanderin'?

northmn

  • Guest
Re: Mike Brooks: C'mon, tell us how ya did it!
« Reply #2 on: February 15, 2010, 07:08:53 PM »
That trick would make a great tutorial.

DP
Logged

Offline Acer Saccharum

  • Hero Member
  • *****
  • Posts: 19311
    • Thomas A Curran
Re: Mike Brooks: C'mon, tell us how ya did it!
« Reply #3 on: February 15, 2010, 07:24:31 PM »
I don't get you, Mike. So many of your guns you work so hard to put worm holes IN, and this one, when they are already there, you get rid of them.

Puzzled in NY.

Tom
Logged
Tom Curran's web site : http://monstermachineshop.net
Ramrod scrapers are all sold out.

Offline Mike Brooks

  • Hero Member
  • *****
  • Posts: 13415
    • Mike Brooks Gunmaker
Re: Mike Brooks: C'mon, tell us how ya did it!
« Reply #4 on: February 15, 2010, 08:01:25 PM »
Dear Puzzled in NY,
 Worm holes are OK, a termite colony is NOT OK! ;)
Logged
NEW WEBSITE! www.mikebrooksflintlocks.com
Say, any of you boys smithies? Or, if not smithies per se, were you otherwise trained in the metallurgic arts before straitened circumstances forced you into a life of aimless wanderin'?

Offline Acer Saccharum

  • Hero Member
  • *****
  • Posts: 19311
    • Thomas A Curran
Re: Mike Brooks: C'mon, tell us how ya did it!
« Reply #5 on: February 15, 2010, 08:04:42 PM »
too funny.
Logged
Tom Curran's web site : http://monstermachineshop.net
Ramrod scrapers are all sold out.

The other DWS

  • Guest
Re: Mike Brooks: C'mon, tell us how ya did it!
« Reply #6 on: February 15, 2010, 09:37:13 PM »
REAL nice on the grain match,  helps a lot to have a whole plank of scraps to find the right piece I'd bet. one good argument against pre-carved stocks
I had to look hard with a fair amount of imagination to find the patches.  did you use irregular shaped pieces?  what adhesive did you use?
Logged

Offline Mike Brooks

  • Hero Member
  • *****
  • Posts: 13415
    • Mike Brooks Gunmaker
Re: Mike Brooks: C'mon, tell us how ya did it!
« Reply #7 on: February 15, 2010, 09:39:53 PM »
Quote
did you use irregular shaped pieces?
Beats me, couple years ago now.
Quote
what adhesive did you use?
Probably some cheapo two part epoxy I had laying around.
Logged
NEW WEBSITE! www.mikebrooksflintlocks.com
Say, any of you boys smithies? Or, if not smithies per se, were you otherwise trained in the metallurgic arts before straitened circumstances forced you into a life of aimless wanderin'?

J.D.

  • Guest
Re: Mike Brooks: C'mon, tell us how ya did it!
« Reply #8 on: February 16, 2010, 11:13:13 PM »
This might be a good example of a filler made of stained wood dust mixed with epoxy.  ;D
Logged

Offline Mike Brooks

  • Hero Member
  • *****
  • Posts: 13415
    • Mike Brooks Gunmaker
Re: Mike Brooks: C'mon, tell us how ya did it!
« Reply #9 on: February 16, 2010, 11:24:19 PM »
Quote from: J.D. on February 16, 2010, 11:13:13 PM
This might be a good example of a filler made of stained wood dust mixed with epoxy.  ;D
Tried it before, sticks out like a sore thumb. ;)
Logged
NEW WEBSITE! www.mikebrooksflintlocks.com
Say, any of you boys smithies? Or, if not smithies per se, were you otherwise trained in the metallurgic arts before straitened circumstances forced you into a life of aimless wanderin'?

northmn

  • Guest
Re: Mike Brooks: C'mon, tell us how ya did it!
« Reply #10 on: February 19, 2010, 05:56:01 PM »
I have to do something similar for a ramrod runout.  Like it better than a plate.  What brand of beer works best???  How much ???

DP
Logged

Offline Mike Brooks

  • Hero Member
  • *****
  • Posts: 13415
    • Mike Brooks Gunmaker
Re: Mike Brooks: C'mon, tell us how ya did it!
« Reply #11 on: February 19, 2010, 08:28:01 PM »
Quote from: northmn on February 19, 2010, 05:56:01 PM
I have to do something similar for a ramrod runout.  Like it better than a plate.  What brand of beer works best???  How much ???

DP
Any old timey beer works well. I like brands my grand father used to drink. You know you have had enough when the repair seems like it will be easy. ;)
Logged
NEW WEBSITE! www.mikebrooksflintlocks.com
Say, any of you boys smithies? Or, if not smithies per se, were you otherwise trained in the metallurgic arts before straitened circumstances forced you into a life of aimless wanderin'?

TomK

  • Guest
Re: Mike Brooks: C'mon, tell us how ya did it!
« Reply #12 on: February 20, 2010, 01:35:11 AM »
Termites in Iowa? Tell me you went way way south to pick up that firewood! Nice work of course!
Logged
Pages: [1]   Go Up
« previous next »