« previous next »
Pages: [1]   Go Down

Author Topic: Fore End Help **  (Read 5306 times)

Offline James Rogers

  • Hero Member
  • *****
  • Posts: 3164
  • James Rogers
    • Fowling Piece
Fore End Help **
« on: July 29, 2010, 06:01:59 PM »
I have a long barreled gun (6' oct/round) I am working on that came to me along with a pre-carved butt stock. The lower fore end is about half the length of the octagon part of the octagon to round barrel.

I have cut back the width of the  fore stock to 1/16" at the round part of the barrel and 1/8" at the octagon part.

Should I transition my 1/8 to 1/16 near the wedding band since the lower fore stock is so short or should I bring the 1/16" all the way back to the entry pipe area on the VERY short lower fore stock?

Any opinions are appreciated.

Thanks
James
« Last Edit: July 29, 2010, 06:30:24 PM by James Rogers »
Logged

Offline rich pierce

  • Administrator
  • Hero Member
  • *
  • Posts: 19538
Re: Fore End Help **
« Reply #1 on: July 29, 2010, 06:25:57 PM »
6" does not sound like a long barreled gun to me, LOL.  I do my tapering based on the entry thimble location, and let the rest fall where it may.  No abrupt transition, actually.
Logged
Andover, Vermont

Offline James Rogers

  • Hero Member
  • *****
  • Posts: 3164
  • James Rogers
    • Fowling Piece
Re: Fore End Help **
« Reply #2 on: July 29, 2010, 06:34:02 PM »
Quote from: richpierce on July 29, 2010, 06:25:57 PM
6" does not sound like a long barreled gun to me, LOL.  I do my tapering based on the entry thimble location, and let the rest fall where it may.  No abrupt transition, actually.

 ;D  Thanks. I fixed that to 6'.

Logged

Offline Dr. Tim-Boone

  • Global Moderator
  • Hero Member
  • *
  • Posts: 6538
  • I Like this hat!!
Re: Fore End Help **
« Reply #3 on: July 29, 2010, 06:34:49 PM »
Well........I am thinking the transition from 1/8" tp one 1/16" should be at the entry/rear thimble.. the wedding band is not the issue.......  it will be a long skinny gun!! assuming that you ment 6'... :o

« Last Edit: July 29, 2010, 11:40:48 PM by DrTimBoone »
Logged
De Oppresso Liber
Marietta, GA

Liberty is the only thing you cannot have unless you are willing to give it to others. – William Allen White

Learning is not compulsory...........neither is survival! - W. Edwards Deming

Offline Jim Filipski

  • Hero Member
  • *****
  • Posts: 642
    • Jim W. Filipski Flintlocks
Re: Fore End Help **
« Reply #4 on: July 29, 2010, 06:34:54 PM »
I second what Rich said; the blend is at the rear thimble area
Jim
Logged
" Associate with men of good quality,  if you esteem your own reputation:
for it is better to be alone than in bad company. "      -   George Washington

"A brush of the hand
of Providence is behind what is done with good heart."

Offline James Rogers

  • Hero Member
  • *****
  • Posts: 3164
  • James Rogers
    • Fowling Piece
Re: Fore End Help **
« Reply #5 on: July 29, 2010, 06:45:48 PM »
Thanks guys. What you both have said is what I perceived as correct just as on any other gun but I am just not used to seeing  a 14" or so extra inches of octagon past the entry area.  ;D
« Last Edit: July 29, 2010, 06:49:01 PM by James Rogers »
Logged

Offline Jim Filipski

  • Hero Member
  • *****
  • Posts: 642
    • Jim W. Filipski Flintlocks
Re: Fore End Help **
« Reply #6 on: July 29, 2010, 06:54:38 PM »
James,
 Where did you get the 60" barrel from if I may ask?
Jim
Logged
" Associate with men of good quality,  if you esteem your own reputation:
for it is better to be alone than in bad company. "      -   George Washington

"A brush of the hand
of Providence is behind what is done with good heart."

Offline James Rogers

  • Hero Member
  • *****
  • Posts: 3164
  • James Rogers
    • Fowling Piece
Re: Fore End Help **
« Reply #7 on: July 29, 2010, 06:58:17 PM »
Jim it's Rayl or "Rail" due to it's length.  ;D
Logged

Offline Jim Filipski

  • Hero Member
  • *****
  • Posts: 642
    • Jim W. Filipski Flintlocks
Re: Fore End Help **
« Reply #8 on: July 29, 2010, 07:27:29 PM »
I figured it was one of Ed's. That a cool size barrel can't wait to see pics of your build
Logged
" Associate with men of good quality,  if you esteem your own reputation:
for it is better to be alone than in bad company. "      -   George Washington

"A brush of the hand
of Providence is behind what is done with good heart."

Offline Acer Saccharum

  • Hero Member
  • *****
  • Posts: 19311
    • Thomas A Curran
Re: Fore End Help **
« Reply #9 on: July 29, 2010, 07:45:23 PM »
James, will there be a swell at the entry pipe? If so, that would be a good place to do the transition.

You can also file the oct to 16 sides ahead of the entry pipe area.

If I understand what you mean.

T
« Last Edit: July 29, 2010, 07:50:00 PM by Acer Saccharum »
Logged
Tom Curran's web site : http://monstermachineshop.net
Ramrod scrapers are all sold out.

Offline James Rogers

  • Hero Member
  • *****
  • Posts: 3164
  • James Rogers
    • Fowling Piece
Re: Fore End Help **
« Reply #10 on: July 30, 2010, 09:57:13 PM »
Quote from: JWFilipski on July 29, 2010, 07:27:29 PM
I figured it was one of Ed's. That a cool size barrel can't wait to see pics of your build

Jim, It's going to be something like like you have never seen and will not want to see again.  ;D
Unfortunately my hands are tied a bit on how it's going to look.
Logged

Offline James Rogers

  • Hero Member
  • *****
  • Posts: 3164
  • James Rogers
    • Fowling Piece
Re: Fore End Help **
« Reply #11 on: July 30, 2010, 09:59:19 PM »
Quote from: Acer Saccharum on July 29, 2010, 07:45:23 PM
James, will there be a swell at the entry pipe? If so, that would be a good place to do the transition.

You can also file the oct to 16 sides ahead of the entry pipe area.

If I understand what you mean.

T

Tom,
I had thought of using a swell but now I may smooth it on out. I have a 16 facet now down near the ring.

Thanks
James
Logged
Pages: [1]   Go Up
« previous next »