« previous next »
Pages: [1]   Go Down

Author Topic: Bison powderhorn, part 4, finished carving.  (Read 6639 times)

Offline Rolf

  • Hero Member
  • *****
  • Posts: 1764
  • There's more than one way to skin a cat.
Bison powderhorn, part 4, finished carving.
« on: October 07, 2008, 07:59:52 PM »
I had originally plan to file a large octagon spout and inlet silver filigree panels on four of the sides. I was unsure if the walls were thick enough for this, so I did a short octagon tip followed by a candy cane/spiral pattern. It worked out nicely.
Thanks for the idea, FL flinter.


The yellow tape shows where I'm going to make silver filigree bands. The horn has a two piece butt plug. The inner plug is glued in with epoxy and made  3/4" ash plank. The core isn't cut out jet. The outer plug will be of 3/8" black walnut and rimmed with a silver filigree band.

 I'll post pictures when Ive done the silver work.

Best regards

Rolfkt
« Last Edit: October 08, 2008, 07:46:39 AM by Rolfkt »
Logged

Offline sydney

  • Sr. Member
  • ****
  • Posts: 357
Re: Bison powderhorn, part 4, finished carving.
« Reply #1 on: October 07, 2008, 08:10:20 PM »
Very nice --please post more pictures as you continue
            Thanks   Sydney
Logged

Offline Scott Bumpus

  • Sr. Member
  • ****
  • Posts: 481
Re: Bison powderhorn, part 4, finished carving.
« Reply #2 on: October 07, 2008, 11:50:42 PM »
Very nice.  I look forward to seeing the silver work. That will be one fine horn!
Logged
YOU CAN ONLY BE LOST IF YOU GIVE A @!*% WHERE THE $#*! YOU ARE!!

Offline Elnathan

  • Hero Member
  • *****
  • Posts: 1773
Re: Bison powderhorn, part 4, finished carving.
« Reply #3 on: October 08, 2008, 01:07:30 AM »
That is awfully impressive. How did you do the spiral?
Logged
A man can never have too much red wine, too many books, or too much ammunition -  Rudyard Kipling

Offline Tim Crosby

  • Administrator
  • Hero Member
  • *
  • Posts: 18391
  • AKA TimBuckII
Re: Bison powderhorn, part 4, finished carving.
« Reply #4 on: October 08, 2008, 02:09:49 AM »
 Looking good.

Tim C.
Logged

Offline Randy Hedden

  • Hero Member
  • *****
  • Posts: 2250
  • American Mountain Men #1393
Re: Bison powderhorn, part 4, finished carving.
« Reply #5 on: October 08, 2008, 05:28:51 AM »
Rolf,

It looks real good so far. Be sure and post pictures when you get it done.

Randy Hedden

www.harddogrifles.com
Logged
American Mountain Men #1393

Offline FL-Flintlock

  • Hero Member
  • *****
  • Posts: 2176
    • Fire & Iron Mfg.
Re: Bison powderhorn, part 4, finished carving.
« Reply #6 on: October 08, 2008, 06:14:07 AM »
Looks great so far Rolf, can't wait to see it when it's done!  :)
Logged
The answers you seek are found in the Word, not the world.

Offline Rolf

  • Hero Member
  • *****
  • Posts: 1764
  • There's more than one way to skin a cat.
Re: Bison powderhorn, part 4, finished carving.
« Reply #7 on: October 08, 2008, 04:06:28 PM »
Thank you for your kind comments. I'll post pictures of the silver work as it progresses.

Elnathan, carving a spiral is easier than it looks. The trick is to lay out the pattern correctly.

1. Tape a ring of masking tape around the spout where you want the top and bottom of the spiral.

2. Split the rings and gently pry the tape lose. Divide the length of the tapes with the number of flutes you want.

3. Tape the top and bottom of the spout again and transfer the measurements to the new tape rings.

4. Stretch masking tape between the marks on the two rings. Make sure the tape follows a straight line, not a arc.

5. Follow the edge of the tape when cutting the flutes. First I used a knife edge needle file to cut a narrow 2mm (0.08") deep trench. I widened the trench with a triangle needle, followed with a round file. Then I rounded the flutes with sand paper.


Best regards

Rolfkt
Logged

Offline Elnathan

  • Hero Member
  • *****
  • Posts: 1773
Re: Bison powderhorn, part 4, finished carving.
« Reply #8 on: October 09, 2008, 12:29:37 AM »
Thanks. I'll bear that in mind.
Logged
A man can never have too much red wine, too many books, or too much ammunition -  Rudyard Kipling

Offline Brian

  • Hero Member
  • *****
  • Posts: 6364
Re: Bison powderhorn, part 4, finished carving.
« Reply #9 on: October 09, 2008, 05:07:54 AM »
Very nice indeed!  It will be spectacular when you get the silver on it.  Great idea!
Logged
"This is my word, and as such is beyond contestation"

ottawa

  • Guest
Re: Bison powderhorn, part 4, finished carving.
« Reply #10 on: October 10, 2008, 12:20:12 AM »
cant beleav that was one of those you posted with all the scratches and stuff when ya got it good job ;D
Logged

wwpete52

  • Guest
Re: Bison powderhorn, part 4, finished carving.
« Reply #11 on: October 15, 2008, 08:23:02 PM »
Beautiful horn!
Logged
Pages: [1]   Go Up
« previous next »