AmericanLongRifles Forums
Welcome,
Guest
. Please
login
or
register
.
1 Hour
1 Day
1 Week
1 Month
Forever
Login with username, password and session length
News:
Home
Help
Login
Register
AmericanLongRifles Forums
»
General discussion
»
Gun Building
»
Ramrod question
« previous
next »
Print
Pages: [
1
]
Go Down
Author
Topic: Ramrod question (Read 5052 times)
Scout
Sr. Member
Posts: 284
Mongrel Rifle School of North Florida
Ramrod question
«
on:
February 28, 2011, 03:58:34 AM »
I have seen ramrods with a "Barber pole" effect on them. Is this a wood pattern like curly maple or is it a man made finish like the burnt rope effect I have read about ?
Logged
She ain't Purdy but she shoots real good !
Longknife
Hero Member
Posts: 2091
Re: Ramrod question
«
Reply #1 on:
February 28, 2011, 04:02:03 AM »
That burnt rope thing don't work worth a durn!!!!!!!! It is usually made by staining the ramrod.....Ed
Logged
Ed Hamberg
JB2
Guest
Re: Ramrod question
«
Reply #2 on:
February 28, 2011, 04:56:52 AM »
I used a propane torch, freehand. Talk about a few tense moments, it was the only ramrod I had at the time! If I ever do it again, I'll use the same torch, but I'd wrap tape around the rod in a spiral to act as a guide.
Logged
JB2
Guest
Re: Ramrod question
«
Reply #3 on:
February 28, 2011, 04:57:38 AM »
Oh yeah, and practice on something other than my only ramrod first!
Logged
roamer
Guest
Re: Ramrod question
«
Reply #4 on:
February 28, 2011, 06:20:09 AM »
Howdy ,the best and consistent results i've had is by using the flat tool on a wood burning electrical tool..What I did was to chuck the end of the ramrod into my Dads 1954 rebuilt Shopsmith.Supported the length in a made vblock. My son Nick slowly hand turned the chuck and concentrated on the depth and consistency
Logged
omark
Guest
Re: Ramrod question
«
Reply #5 on:
February 28, 2011, 07:11:22 AM »
the only one i ever did i took a strip of leather probably 3/4 inch thick, wet it good in water, wrapped it on the rod, then used a torch. probably didnt need to wet it, but the leather was not burned and was reusable.. mark
Logged
Blacksmoke
Hero Member
Posts: 862
"Old age and treachery beats youth and skill"
Re: Ramrod question
«
Reply #6 on:
February 28, 2011, 08:45:32 AM »
I do the same as Mark but instead using leather I use a strip of 3/4" wide metal and thin enough to wrap easily. Do not hold the torch on the wood too long - just enough to darken it a little. Once it is finished I will submerge the rod in tung oil for a week or so - this will give it some bendabilty with out breaking.
Hugh Toenjes
Logged
H.T.
ken
Guest
Re: Ramrod question
«
Reply #7 on:
February 28, 2011, 06:28:10 PM »
It can be done with masking tape, has to be at least two layers thick and use a propane torch. Has work for me in past . gives nice even lines.
Logged
geb324
Guest
Re: Ramrod question
«
Reply #8 on:
February 28, 2011, 06:47:36 PM »
Use a propane torch start on one end keep the torch about 5 inches from the
ramrod rotate it and move forward no need to scorch it to deep
I move it continously with out stoping to the end slow and steady. Takes only a couple of minutes.
Sand the ramrod and stain and finish. Doesnt have to be perfect a maple stock
is not.
Logged
Longknife
Hero Member
Posts: 2091
Re: Ramrod question
«
Reply #9 on:
February 28, 2011, 07:02:16 PM »
But how PC is this "barber pole" ramrod, was it used in the prior to the 20th century?
??........Ed
Logged
Ed Hamberg
Blacksmoke
Hero Member
Posts: 862
"Old age and treachery beats youth and skill"
Re: Ramrod question
«
Reply #10 on:
February 28, 2011, 07:23:03 PM »
Ed: I've seen quite a number of old original longrifles with the "barber pole" striping - however I cannot swear that the RR was not a replacement - but most old Kentucky's that retain their original RR do not have the feature being discussed. Just my observation, Hugh Toenjes
Logged
H.T.
Dr. Tim-Boone
Global Moderator
Hero Member
Posts: 6538
I Like this hat!!
Re: Ramrod question
«
Reply #11 on:
February 28, 2011, 09:43:42 PM »
I don't know the facts but to me the barber poles look like they go with mid 1900 rifles that have all of thegaudy inlays, sharp pointed triggerguards etc...... Just my taste
Logged
De Oppresso Liber
Marietta, GA
Liberty is the only thing you cannot have unless you are willing to give it to others. – William Allen White
Learning is not compulsory...........neither is survival! - W. Edwards Deming
flintriflesmith
Hero Member
Posts: 1509
Re: Ramrod question
«
Reply #12 on:
February 28, 2011, 11:26:19 PM »
Quote from: Longknife on February 28, 2011, 07:02:16 PM
But how PC is this "barber pole" ramrod, was it used in the prior to the 20th century?
??........Ed
I believe the conclusion often reached is that the stripped ramrods that survive are mostly very late 18th century
or later
. That doesn't mean they weren't around in 1780-90 but ... well that's just like everything else where we can only say what the earliest known examples are.
I wouldn't put one on a Rev War period rifle and expect it to be considered period correct.
Gary
Logged
"If you accept your thoughts as facts, then you will no longer be looking for new information, because you assume that you have all the answers."
http://flintriflesmith.com
Print
Pages: [
1
]
Go Up
« previous
next »
AmericanLongRifles Forums
»
General discussion
»
Gun Building
»
Ramrod question