« previous next »
Pages: [1]   Go Down

Author Topic: Brass???  (Read 5313 times)

Offline Don Getz

  • Hero Member
  • *****
  • Posts: 6853
Brass???
« on: September 01, 2011, 03:20:15 PM »
Am working on a J. P. Beck rifle, and it isn't really a barn gun version, am putting all the parts on it, but NO carving.   Had
a strange thing happen.   Wanted to put a nose cap on it, and cut a piece big enough to wrap around the forend, then
took my torch and heated it red hot, quenched it, and it was still hard, could not even bend it with my hands.....not normal.   I don't know where I bought this stuff, it was a sheet about 6" x 10", and marked .030, but now I have no idea
of what it is.   Luckily I did have another piece of brass and I cut another piece out, heated and quenched it and it worked
beautifully.   I am still curious as to what that other piece is made of...................Don
Logged

Offline Mike Brooks

  • Hero Member
  • *****
  • Posts: 13415
    • Mike Brooks Gunmaker
Re: Brass???
« Reply #1 on: September 01, 2011, 03:22:41 PM »
Knowing you retired guys it's probably sheet gold......
Logged
NEW WEBSITE! www.mikebrooksflintlocks.com
Say, any of you boys smithies? Or, if not smithies per se, were you otherwise trained in the metallurgic arts before straitened circumstances forced you into a life of aimless wanderin'?

Offline Don Getz

  • Hero Member
  • *****
  • Posts: 6853
Re: Brass???
« Reply #2 on: September 01, 2011, 03:27:49 PM »
Darn it Mike, I didn't think of that, and I just gave it away............Don
Logged

Offline Mike Brooks

  • Hero Member
  • *****
  • Posts: 13415
    • Mike Brooks Gunmaker
Re: Brass???
« Reply #3 on: September 01, 2011, 03:32:43 PM »
Well then you better start storing your gold stash in a seperate drawer. ;)
Logged
NEW WEBSITE! www.mikebrooksflintlocks.com
Say, any of you boys smithies? Or, if not smithies per se, were you otherwise trained in the metallurgic arts before straitened circumstances forced you into a life of aimless wanderin'?

Offline Dr. Tim-Boone

  • Global Moderator
  • Hero Member
  • *
  • Posts: 6538
  • I Like this hat!!
Re: Brass???
« Reply #4 on: September 01, 2011, 04:16:04 PM »
Armor plate left over from WWII???
Logged
De Oppresso Liber
Marietta, GA

Liberty is the only thing you cannot have unless you are willing to give it to others. – William Allen White

Learning is not compulsory...........neither is survival! - W. Edwards Deming

omark

  • Guest
Re: Brass???
« Reply #5 on: September 01, 2011, 06:50:52 PM »
just kinda thinking out loud, but, is there any chance it is brass plated steel of some sort??    mark
Logged

Offline C Wallingford

  • Hero Member
  • *****
  • Posts: 863
  • Northern Kentucky
    • CW Knives
Re: Brass???
« Reply #6 on: September 01, 2011, 07:27:37 PM »
Don--
 Maybe John could use it for barrel material! ;)
Logged

Offline LRB

  • Hero Member
  • *****
  • Posts: 1567
    • WICK ELLERBE
Re: Brass???
« Reply #7 on: September 01, 2011, 08:18:57 PM »
 Don, I had the same thing happen with a piece of brass door kick plate. I tried 4 or 5 times and gave it up. I assme it was alloyed to be hard and stay that way.
Logged

Offline C. ALTLAND

  • Jr. Member
  • **
  • Posts: 76
    • Chris Altland - York County Firelocks - Authentic 18th Century Flintlock Pistol Parts Sets & Pistol Restoration Parts
Re: Brass???
« Reply #8 on: September 01, 2011, 11:27:18 PM »
Hey Don let me know if you need any more sheet brass. I have plenty of .030 & .050 brass. Can send you a care package.
Logged
YORK COUNTY FIRELOCKS  PH# 717-755-3682 
http://www.firelockpistols.com/

Offline bgf

  • Hero Member
  • *****
  • Posts: 1403
Re: Brass???
« Reply #9 on: September 01, 2011, 11:47:20 PM »
It might actually be useful if you could do that to "normal" brass, after it had been shaped, of course.  I suppose it could have been a slightly off alloy and then work hardened by the rollers.  On the other hand I had a pistol buttcap one time that was a little like that; worked more like high carbon steel than brass; it was evident from the amount of sand sticking in/on it that they had taken a lot of care manufacturing it.  You should have performed some scientific tests on it, such as shooting it with various size balls at different velocities :). 
Logged

Offline Curtis

  • Hero Member
  • *****
  • Posts: 2338
  • Missouri
Re: Brass???
« Reply #10 on: September 02, 2011, 12:40:47 AM »
Don, was it possibly shim stock material?

Curtis
Logged
Curtis Allinson
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Sometimes, late at night when I am alone in the inner sanctum of my workshop and no one else can see, I sand things using only my fingers for backing

Offline draken

  • Sr. Member
  • ****
  • Posts: 404
Re: Brass???
« Reply #11 on: September 02, 2011, 12:56:10 AM »
Don, did the stuff cut harder too?   I've been having the same problem, and the metal seems a little tougher to cut as well.
Logged
Dick 

Times have sure changed. Gun control used to mean keeping the muzzle pointed in a safe direction

Never write a check with your mouth that your butt can't cash!

Offline FL-Flintlock

  • Hero Member
  • *****
  • Posts: 2176
    • Fire & Iron Mfg.
Re: Brass???
« Reply #12 on: September 02, 2011, 05:23:50 AM »
Maybe it's cold rolled  ::)
Logged
The answers you seek are found in the Word, not the world.
Pages: [1]   Go Up
« previous next »