Author Topic: Barrel wall thickness  (Read 4232 times)

Offline Ezra

  • Hero Member
  • *****
  • Posts: 1579
Barrel wall thickness
« on: May 25, 2012, 04:57:49 AM »
Generally speaking, and assuming 12L14 steel, and an octagonal barrel in .50 caliber, what is the accepted minimum barrel thickness for a pistol barrel at the breech?  Is .18" too thin?   Black powder only.  Thanks guys.


Ez
"Rules are for the obedience of fools and guidance of wise men"

Offline D. Taylor Sapergia

  • Member 3
  • Hero Member
  • *
  • Posts: 12671
Re: Barrel wall thickness
« Reply #1 on: May 25, 2012, 06:00:24 AM »
No, it's not too thin.  But it is thin.  So no rifle loads!  Most original pistols were thinner than that at the breech, according to one reference I have.
D. Taylor Sapergia
www.sapergia.blogspot.com

Art is not an object.  It is the excitement inspired by the object.

Offline Don Getz

  • Hero Member
  • *****
  • Posts: 6853
Re: Barrel wall thickness
« Reply #2 on: May 25, 2012, 03:20:56 PM »
Ezra.........should be no problem, you are almost at 7/8" diameter, which is a popular size in a rifle barrel in 50 cal....Don

coutios

  • Guest
Re: Barrel wall thickness
« Reply #3 on: May 25, 2012, 05:00:37 PM »
  Are we assuming this is a smooth bore ????  I'll only solder the rear lug on these .50cal/7/8 barrels...  More is better at the breech in my small mind..

Regards
Dave

Offline Bob Roller

  • Hero Member
  • *****
  • Posts: 9694
Re: Barrel wall thickness
« Reply #4 on: May 25, 2012, 07:36:00 PM »
Dixie Gun Works lists 7/8x50 straight octagon and 12" long made from 1137. Sounds like a better idea to me and for aroung $70 and threaded for the breech plug.
That 1137 tells me these may be Green Mountain barrels.

Bob Roller

Offline Don Getz

  • Hero Member
  • *****
  • Posts: 6853
Re: Barrel wall thickness
« Reply #5 on: May 26, 2012, 04:18:04 PM »
Think about this.  Over the years we have made some 13/16" (.812) diameter barrels in 50 cal.  I am not going to tell you
about the ridiculous test loads we did in one.   The biggest problem in using a barrel this small is cutting dovetails into it
If you don't have a vertical mill to do it, I would suggest you solder them onto it.    Personally, I would never build a gun
with a barrel this small.   We have also made some 3/4" barrels in small calibres, but have discontinued that, too much
like a "toy".   Years ago we had a guy here in Pa. who was shooting in a lot of matches and winning more than his share.
He shot a gun with one of the 13/16"  50 cal. barrels, shot 50 grains of powder, and was deadly with it.   As for me, I
would prefer a heavier barrel for target shooting...............Don

Offline Roger Fisher

  • Hero Member
  • *****
  • Posts: 6805
Re: Barrel wall thickness
« Reply #6 on: May 27, 2012, 02:48:57 AM »
Think about this.  Over the years we have made some 13/16" (.812) diameter barrels in 50 cal.  I am not going to tell you
about the ridiculous test loads we did in one.   The biggest problem in using a barrel this small is cutting dovetails into it
If you don't have a vertical mill to do it, I would suggest you solder them onto it.    Personally, I would never build a gun
with a barrel this small.   We have also made some 3/4" barrels in small calibres, but have discontinued that, too much
like a "toy".   Years ago we had a guy here in Pa. who was shooting in a lot of matches and winning more than his share.
He shot a gun with one of the 13/16"  50 cal. barrels, shot 50 grains of powder, and was deadly with it.   As for me, I
would prefer a heavier barrel for target shooting...............Don
Lemme guess,, Lonnie Seitz  The turkeys wouldn't stick their heads out of the bags for him ;D

Offline Don Getz

  • Hero Member
  • *****
  • Posts: 6853
Re: Barrel wall thickness
« Reply #7 on: May 27, 2012, 04:06:15 AM »
Roger.............you have a good memory.     Lonnie was deadly with that  little light gun.   Last time I heard of him he was
living in the northern part of the state, raising horses, or maybe it was just horsing around, not sure.......Don