« previous next »
Pages: [1]   Go Down

Author Topic: 3/4ths-inch barrel calibers?  (Read 7553 times)

caliber45

  • Guest
3/4ths-inch barrel calibers?
« on: September 10, 2012, 05:29:23 PM »
Could one of you fine folks tell me the largest caliber available in 3/4ths-inch barrels (straight, not swamped) of modern manufacture? Tks! -- paulallen, greencastle, IN
Logged

Offline Bill of the 45th

  • Hero Member
  • *****
  • Posts: 1436
  • Gaylord, Michigan
Re: 3/4ths-inch barrel calibers?
« Reply #1 on: September 10, 2012, 06:01:10 PM »
I think .40 cal is a big as they go, at least it's all I've ever seen them in.  Troy Roope at Stonewall Creek has some 3/4" Rayl barrels from .25 to .40.  He had a number of them at Dixon's

Bill
Logged
Bill Knapp
Over the Hill, What Hill, and when did I go over it?

Goose

  • Guest
Re: 3/4ths-inch barrel calibers?
« Reply #2 on: September 10, 2012, 11:34:17 PM »
I had a couple of 45 cal built on 3/4 brls. Getz made them for me. Also a couple of 50s on 13/16. Took about a yesr and half. Nice light brls tho, worth the wait
Logged

Old Salt

  • Guest
Re: 3/4ths-inch barrel calibers?
« Reply #3 on: September 12, 2012, 01:40:17 AM »
I have a 3/4" .40 from Green Mountain.  It's part of an in-the-white rifle I bought from Tip Curtis.
Logged

Offline Mike Brooks

  • Hero Member
  • *****
  • Posts: 13415
    • Mike Brooks Gunmaker
Re: 3/4ths-inch barrel calibers?
« Reply #4 on: September 12, 2012, 02:34:41 AM »
I wouldn't use one, you end up with horrible architecture.
Logged
NEW WEBSITE! www.mikebrooksflintlocks.com
Say, any of you boys smithies? Or, if not smithies per se, were you otherwise trained in the metallurgic arts before straitened circumstances forced you into a life of aimless wanderin'?

Offline Ryan McNabb

  • Full Member
  • ***
  • Posts: 234
    • McNabb's Station
Re: 3/4ths-inch barrel calibers?
« Reply #5 on: September 12, 2012, 04:03:54 AM »
Quote from: Mike Brooks on September 12, 2012, 02:34:41 AM
I wouldn't use one, you end up with horrible architecture.

Absolutely.
Logged

Offline TMerkley

  • Hero Member
  • *****
  • Posts: 634
Re: 3/4ths-inch barrel calibers?
« Reply #6 on: September 12, 2012, 05:21:11 AM »
The 3/4 barrel would be pretty nice for a youth model regardless of cal.
Logged

Offline kutter

  • Hero Member
  • *****
  • Posts: 715
Re: 3/4ths-inch barrel calibers?
« Reply #7 on: September 12, 2012, 05:33:25 AM »
I've got a GM 3/4 x .40 and a Rayl 3/4 x .40
One will go one a Southern(?) style flint rifle I hope to finish up this winter.
Parts gathering , a bit of work and a lot of thinkin' over the course of a year or so.

Sure is a slim bbl & stock! I like it.
Logged

Offline smokinbuck

  • Hero Member
  • *****
  • Posts: 3004
Re: 3/4ths-inch barrel calibers?
« Reply #8 on: September 12, 2012, 06:00:13 AM »
I've got one rifle with a 3/4X42 barrel but it's not nearly as big as .40. The barrel is a Bill Large .29-.30, depends on who measures it. Takes a .285 ball with .010 ptching and shoots into one hole, depending on who's shooting it.
Mark
Logged
Mark

Offline Don Getz

  • Hero Member
  • *****
  • Posts: 6853
Re: 3/4ths-inch barrel calibers?
« Reply #9 on: September 12, 2012, 02:55:19 PM »
I have convinced son John not to make any more 3/4" barrels, it's like building a "toy" rifle.   When I ran the barrel business I refused to make them............Don
Logged

Offline bob in the woods

  • Hero Member
  • *****
  • Posts: 4555
Re: 3/4ths-inch barrel calibers?
« Reply #10 on: September 12, 2012, 04:28:46 PM »
I had a 3/4 in  36 cal for a while.  You really have to watch the tenons and make sure they are slotted cause it doesn't take much to bend that barrel. Not a permanent, radical bend,but enough to throw your sights out.
Logged

Offline Robby

  • Hero Member
  • *****
  • Posts: 2655
  • NYSSR ―
Re: 3/4ths-inch barrel calibers?
« Reply #11 on: September 12, 2012, 04:54:54 PM »
This is a 3/4" barrel. Is the architecture horrible? I don't know, I'm largely ignorant on the subject. It holds and shoots nice though.

Robby
Logged
molon labe
We the people are the rightful masters of both Congress and the courts, not to overthrow the Constitution but to overthrow the men who pervert the Constitution. A. Lincoln

Offline Mike Brooks

  • Hero Member
  • *****
  • Posts: 13415
    • Mike Brooks Gunmaker
Re: 3/4ths-inch barrel calibers?
« Reply #12 on: September 12, 2012, 05:58:12 PM »
Quote from: Robby on September 12, 2012, 04:54:54 PM
This is a 3/4" barrel. Is the architecture horrible? I don't know, I'm largely ignorant on the subject. It holds and shoots nice though.

Robby
Have to have a look over the top. Maybe you and others can pull it off, but I can't.
Logged
NEW WEBSITE! www.mikebrooksflintlocks.com
Say, any of you boys smithies? Or, if not smithies per se, were you otherwise trained in the metallurgic arts before straitened circumstances forced you into a life of aimless wanderin'?

Daryl

  • Guest
Re: 3/4ths-inch barrel calibers?
« Reply #13 on: September 12, 2012, 06:22:09 PM »
Friend of mine has a 13/16" (actually a mite smaller) in .50. It's a Spanish or Italian barrel and VERY thin that he used in a re-stock job. I would not shoot it, personally. The gun is way too light for me to hold, like shooting a kid's 5 pound rifle with a man's stock on it. The thinness of the barrel of unknown steel spooks me.
Logged

Offline Robby

  • Hero Member
  • *****
  • Posts: 2655
  • NYSSR ―
Re: 3/4ths-inch barrel calibers?
« Reply #14 on: September 13, 2012, 06:08:30 PM »
Mike, I don't have a shot of that angle, but when I made it, I remember thinking "Olive OYL"!  :(
You know, of Popeye fame, skinny and featureless. I do remember thinking at the time that I should have made a tapered shim and soldered it to the lock bolster to give it some better lines. So while I didn't pull it off, I do think it could be done. The lady I made it for is definitely no Olive Oyl and enjoys it. Its a .32.
Robby
Logged
molon labe
We the people are the rightful masters of both Congress and the courts, not to overthrow the Constitution but to overthrow the men who pervert the Constitution. A. Lincoln

Offline Kermit

  • Hero Member
  • *****
  • Posts: 3099
Re: 3/4ths-inch barrel calibers?
« Reply #15 on: September 13, 2012, 07:04:47 PM »
Are we talking about a straight 3/4" barrel? What about "A" weight swamped barrels? Are they in the same "too skinny" category? Some of them are mighty long too. I see a lot of makers will build  "A" weights in .40. Maybe even .45?
Logged
"Anything worth doing is worth doing slowly." Mae West

caliber45

  • Guest
Re: 3/4ths-inch barrel calibers?
« Reply #16 on: September 15, 2012, 04:41:05 PM »
Thanks for the info, gents. I did not intend to create a "good thing-bad thing" discussion with my question; just wanted some information. I won't voice my own reasons for liking the 3/4ths-inch barrels because I don't think this forum is intended to be a "yes they are-no they ain't" platform. To each his own, I say. Thanks again! -- paulallen, greencastle, IN
Logged

Offline Gene Carrell

  • Hero Member
  • *****
  • Posts: 522
Re: 3/4ths-inch barrel calibers?
« Reply #17 on: September 20, 2012, 01:18:57 PM »
My squirrel  rifle has a Cecil Brooks 3/4", 32cal bbl, 40'' long. Makes a dandy lightweight  rifle in the woods.
Logged
Gene

Offline Mike Brooks

  • Hero Member
  • *****
  • Posts: 13415
    • Mike Brooks Gunmaker
Re: 3/4ths-inch barrel calibers?
« Reply #18 on: September 20, 2012, 07:18:47 PM »
Good ol Grandpa Cecil......how's he doing anyway?
Logged
NEW WEBSITE! www.mikebrooksflintlocks.com
Say, any of you boys smithies? Or, if not smithies per se, were you otherwise trained in the metallurgic arts before straitened circumstances forced you into a life of aimless wanderin'?
Pages: [1]   Go Up
« previous next »