« previous next »
Pages: 1 [2]   Go Down

Author Topic: Shaping forestock question  (Read 11670 times)

Offline Acer Saccharum

  • Hero Member
  • *****
  • Posts: 19311
    • Thomas A Curran
Re: Shaping forestock question
« Reply #25 on: September 14, 2012, 09:10:04 PM »
Quote from: Dennis Glazener on September 14, 2012, 08:58:48 PM
[I just drill mine on through making sure to hold a piece of wood on the other side to keep from splintering.
Dennis

I put a little piece of wood on the other side so I don't drill into my hand!
Logged
Tom Curran's web site : http://monstermachineshop.net
Ramrod scrapers are all sold out.

Offline Randy Hedden

  • Hero Member
  • *****
  • Posts: 2250
  • American Mountain Men #1393
Re: Shaping forestock question
« Reply #26 on: September 14, 2012, 10:52:03 PM »
Quote from: Acer Saccharum on September 14, 2012, 09:10:04 PM
Quote from: Dennis Glazener on September 14, 2012, 08:58:48 PM
[I just drill mine on through making sure to hold a piece of wood on the other side to keep from splintering.
Dennis

I put a little piece of wood on the other side so I don't drill into my hand!

Piece of wood?  I just put two layers of masking tape over the exit area of the drill and have never splintered one yet.  I also place the tip of my index finger over the tape so I can feel when the drill is about to break through and can let up on the pressure applied to the drill.  And no, Tom I have never drilled into my finger.

Randy Hedden
Logged
American Mountain Men #1393

Offline Acer Saccharum

  • Hero Member
  • *****
  • Posts: 19311
    • Thomas A Curran
Re: Shaping forestock question
« Reply #27 on: September 14, 2012, 11:30:14 PM »
I haven't drilled my finger yet, but you see the workings of my evil mind.
Logged
Tom Curran's web site : http://monstermachineshop.net
Ramrod scrapers are all sold out.

Offline Dr. Tim-Boone

  • Global Moderator
  • Hero Member
  • *
  • Posts: 6538
  • I Like this hat!!
Re: Shaping forestock question
« Reply #28 on: September 15, 2012, 06:26:52 PM »
Dennis, that works fine when installing the lugs and pipes when the stock is still square.... on a precarve or when you build an Alzheimer's gun and shape the forestock before installing the pipes............ the pin vice is actually very quick and easy...   ;D ;D
Logged
De Oppresso Liber
Marietta, GA

Liberty is the only thing you cannot have unless you are willing to give it to others. – William Allen White

Learning is not compulsory...........neither is survival! - W. Edwards Deming

Offline FL-Flintlock

  • Hero Member
  • *****
  • Posts: 2176
    • Fire & Iron Mfg.
Re: Shaping forestock question
« Reply #29 on: September 16, 2012, 04:47:01 AM »
Quote from: Dr. Tim-Boone on September 15, 2012, 06:26:52 PM
Dennis, that works fine when installing the lugs and pipes when the stock is still square.... on a precarve or when you build an Alzheimer's gun and shape the forestock before installing the pipes............ the pin vice is actually very quick and easy...   ;D ;D

Drink more coffee doc, helps prevent & reverse Alzheimer's.

To help prevent wandering and backside blowout, use a parabolic drill having a four facet 60-65° split or back-ground (thinned web) point, 8-10° chisel relief angle, 5k minimum spindle speed.
« Last Edit: September 16, 2012, 04:52:54 AM by FL-Flintlock »
Logged
The answers you seek are found in the Word, not the world.

Offline Acer Saccharum

  • Hero Member
  • *****
  • Posts: 19311
    • Thomas A Curran
Re: Shaping forestock question
« Reply #30 on: September 16, 2012, 04:56:25 AM »
I like the split point drills.

But you're not going to get 5,000 rpm out of a pin vise!
Logged
Tom Curran's web site : http://monstermachineshop.net
Ramrod scrapers are all sold out.

Offline FL-Flintlock

  • Hero Member
  • *****
  • Posts: 2176
    • Fire & Iron Mfg.
Re: Shaping forestock question
« Reply #31 on: September 16, 2012, 05:11:57 AM »
Quote from: Acer Saccharum on September 16, 2012, 04:56:25 AM
I like the split point drills.

But you're not going to get 5,000 rpm out of a pin vise!

You can when it's chucked in the old Rockwell press.  ;)  ;D
Logged
The answers you seek are found in the Word, not the world.

Offline Acer Saccharum

  • Hero Member
  • *****
  • Posts: 19311
    • Thomas A Curran
Re: Shaping forestock question
« Reply #32 on: September 16, 2012, 05:15:34 AM »
I like your train of thought!
Logged
Tom Curran's web site : http://monstermachineshop.net
Ramrod scrapers are all sold out.

Offline Dr. Tim-Boone

  • Global Moderator
  • Hero Member
  • *
  • Posts: 6538
  • I Like this hat!!
Re: Shaping forestock question
« Reply #33 on: September 16, 2012, 06:03:12 AM »
Its a runaway train... better catch it!!
Logged
De Oppresso Liber
Marietta, GA

Liberty is the only thing you cannot have unless you are willing to give it to others. – William Allen White

Learning is not compulsory...........neither is survival! - W. Edwards Deming
Pages: 1 [2]   Go Up
« previous next »