« previous next »
Pages: [1]   Go Down

Author Topic: Firing system  (Read 5698 times)

wireman

  • Guest
Firing system
« on: September 16, 2012, 11:14:04 PM »
Have mystery cap/ball that has  1/4 inch hole drilled from face of breach 1 1/4 inch back till it connects to nipple the hole hold 15gn of powder
Logged

Offline D. Taylor Sapergia

  • Member 3
  • Hero Member
  • *
  • Posts: 12671
Re: Firing system
« Reply #1 on: September 17, 2012, 02:50:07 AM »
...and?
Logged
D. Taylor Sapergia
www.sapergia.blogspot.com

Art is not an object.  It is the excitement inspired by the object.

wireman

  • Guest
Re: Firing system
« Reply #2 on: September 17, 2012, 05:31:33 AM »
well its 54cal and whats up with 1/4 inch hole, is this the way thay are supposed to be plus its got a funnel 30inchs long that goes down the barrel to pour powder down.
Logged

Daryl

  • Guest
Re: Firing system
« Reply #3 on: September 17, 2012, 08:06:20 AM »
It sounds normal so far, for a bench-type gun. The funnel is used by some shooters to prevent powder granguals from sticking to the bore wall, I assume.
« Last Edit: September 17, 2012, 08:07:22 AM by Daryl »
Logged

Offline Roger Fisher

  • Hero Member
  • *****
  • Posts: 6805
Re: Firing system
« Reply #4 on: September 17, 2012, 06:34:23 PM »
Quote from: wireman on September 17, 2012, 05:31:33 AM
well its 54cal and whats up with 1/4 inch hole, is this the way thay are supposed to be plus its got a funnel 30inchs long that goes down the barrel to pour powder down.
Are you describing a/your Nock type breeching ???  The bench shooters do use a long tube funnel so none of the black stuff sticks to the bore wall. They are fussy to the extreme.
Logged

wireman

  • Guest
Re: Firing system
« Reply #5 on: September 18, 2012, 12:58:11 AM »
It could be beach rifle its heavy enough.Got one those schuetzen real thick butt plate.Also the ram rod tip is real small does not look right for ball.
« Last Edit: September 18, 2012, 01:02:33 AM by wireman »
Logged

Offline Roger Fisher

  • Hero Member
  • *****
  • Posts: 6805
Re: Firing system
« Reply #6 on: September 18, 2012, 02:37:00 AM »
Quote from: wireman on September 18, 2012, 12:58:11 AM
It could be beach rifle its heavy enough.Got one those schuetzen real thick butt plate.Also the ram rod tip is real small does not look right for ball.
And, there surely was a small scraper with that rifle to get down in to that channel to scrape the crud/fouling out...
Logged

Offline T*O*F

  • Hero Member
  • *****
  • Posts: 5123
Re: Firing system
« Reply #7 on: September 18, 2012, 05:37:57 AM »
How do you know that the channel is 1/4 inch?  Have you de-breeched the barrel and measured it?  Those channels are normally no smaller than 3/8ths.
Logged
Dave Kanger

If religion is opium for the masses, the internet is a crack, pixel-huffing orgy that deafens the brain, numbs the senses and scrambles our peer list to include every anonymous loser, twisted deviant, and freak as well as people we normally wouldn't give the time of day.
-S.M. Tomlinson

wireman

  • Guest
Re: Firing system
« Reply #8 on: September 18, 2012, 07:13:13 AM »
No i did not its all bass and i was afraid i would mess it up.But 1/4inch wood dowel fits tight.This is the only cap rifle i have.I was a little worried about the bass as breach plug and then a hole drilled in it.Should take same load as my 54 flintlock 
Logged

Daryl

  • Guest
Re: Firing system
« Reply #9 on: September 18, 2012, 05:32:19 PM »
BRASS? 
Logged

wireman

  • Guest
Re: Firing system
« Reply #10 on: September 18, 2012, 10:52:44 PM »
Yes its brass,it looks like Hawken and that part that houses the trigger and hammer,nipple is one peace then the end has been milled to round and threaded and screws into barrel 5/8 inch and then the hole is drilled back 1 1/4inch to the nipple.Have not shot it yet.
Logged

Offline smylee grouch

  • Hero Member
  • *****
  • Posts: 7910
Re: Firing system
« Reply #11 on: September 19, 2012, 01:17:42 AM »
Can you post some pictures of the gun?
Logged

Offline Ben I. Voss

  • Sr. Member
  • ****
  • Posts: 353
Re: Firing system
« Reply #12 on: September 19, 2012, 04:35:56 AM »
Makes me wonder if it's a Mowrey "Allen and Thurber" with the brass frame?
Logged

Daryl

  • Guest
Re: Firing system
« Reply #13 on: September 19, 2012, 06:16:00 PM »
I had that thought too, Ben, and that it has a bolster-type breech.
Logged

wireman

  • Guest
Re: Firing system
« Reply #14 on: September 23, 2012, 12:53:59 AM »
Ben&Daryl  Thats what it is  ;D I talked to the person i got this from inTenn. and he told me it was a Mowrey had to track down his ex to get the number put over 100miles on my m.c ;D
Logged
Pages: [1]   Go Up
« previous next »