Author Topic: Henry E. Leman part kit (Read 18055 times)

runastav · « **on:** September 24, 2012, 11:50:45 AM »

Hi Guys, more fun

I like the Leman rifle in Track of the Wolf catalog, and the rifles made by Jack Brooks in his web side is very nice! So I order parts from Track O T W , and since I have a Green Mt barrel 15/16" cal 50" I will use that. I asked Jack Brooks some advice, and he recommend the RE Davis " Golcher" percussion lock. And Yes Rolf I will try to paint stipes on the stock hehe

Runar

MarkEngraver · « **Reply #1 on:** September 24, 2012, 08:11:00 PM »

Hey Runar,

Lemans are great guns. For a good knock around ,"Git'er done", work horse kind of gun, Lemans are hard to beat !
I have one myself, built on a early 1970's Douglas 1 1/8 .54 cal barrel, cut to 31 inches. Weighs 13+ lbs. but holds steady and is probably the most accurate gun I own, bar-none ! ( including my cartridge guns !)

I've built a few Lemans for friends and I used the Siler Mountain percussion locks. The lock plate has enough room to allow for profiling the shape a little better (imho), but you find Lemans with several locks in them. Whatever Mr.Henry could procure I suppose !

Have fun with your project, I'm sure we all will watching your progress !! always do !

Mark

Rolf · « **Reply #2 on:** September 25, 2012, 12:45:30 AM »

Quote from: runastav on September 24, 2012, 11:50:45 AM

And Yes Rolf I will try to paint stipes on the stock hehe
Runar

Arrgh!!!!!!!!!!!( Geuss we all have our pet peeves.)

Best regards
Rolf

runastav · « **Reply #3 on:** September 26, 2012, 08:21:29 PM »

Thank you MarkEngraver and Rolf!
Cut the 36" barrel to 32" hmmm 4" bit nice derringer

Made the breech plug, thread a bolt 5/8x18 and stick weld the tang. Length of thread is litle more than 1/2"
Runar

BartSr · « **Reply #4 on:** September 27, 2012, 12:12:55 AM »

Love that tang!

cheyenne · « **Reply #5 on:** September 27, 2012, 12:19:50 AM »

OH BOY! Here we go with another one!!!! Looking forward to this!

runastav · « **Reply #6 on:** September 28, 2012, 07:01:53 PM »

Hi Folks! and thank you BartSr and hlane!
Square off the breech end in stock, and inlet the breech plug.I use the cut off barrelbit for inlet. barrel loops made from steel sheet 1mm
Runar

runastav · « **Reply #7 on:** September 30, 2012, 06:31:45 PM »

Hey Guys!
Jack Brooks send me photos of original H.E.Leman sights and I try to copy them

Runar

runastav · « **Reply #8 on:** October 03, 2012, 12:48:13 PM »

Hey Guys!
Lock inlet, drum install and nipple

Runar

runastav · « **Reply #9 on:** October 03, 2012, 12:58:51 PM »

Old Ford2 · « **Reply #10 on:** October 03, 2012, 02:58:45 PM »

Hello Runar,
Thank you for your great work, pictures, and diligent interest in this wonderful practice.
All the best
Fred

runastav · « **Reply #11 on:** October 06, 2012, 06:39:57 PM »

Hey Guys! and thank you Fred

The triggerplate and trigger made an inlet. Brass Triggergard cleaned up and inlet, hmm begin lock like a rifle

Runar

greybeard · « **Reply #12 on:** October 06, 2012, 07:34:14 PM »

Great post as usual. Nice work. Bob

runastav · « **Reply #13 on:** October 09, 2012, 12:53:48 PM »

Hi Guys, and thank you greybeard

Buttplate, toeplate install. Lots of wood removed, and the cheek rest is made after Jack Brooks pictures and explanation

Runar

Lengd off pull 13-3/4"

smylee grouch · « **Reply #14 on:** October 09, 2012, 02:09:43 PM »

Looks like a nice job again. What are you going to hunt with it?

woodburner · « **Reply #15 on:** October 11, 2012, 04:25:41 AM »

Runastav, your project looks great. Thank you for taking the time to create a pictorial
tutorial.

Tim

PPatch · « **Reply #16 on:** October 11, 2012, 05:23:32 AM »

You are an excellent wood and metal worker Runastav, and your inletting is looking great. Looking forward to your wood treatement/finish.

Dave

runastav · « **Reply #17 on:** October 11, 2012, 08:28:27 PM »

Hi Guys, and thank you all

Smylee grouch, only targetshooting Muzzleloaderhunting is no good in Norway

Capbox instal, I use the perfekt capbox on my H.V.Perry rifle as a inspiration

Runar

Vomitus · « **Reply #18 on:** October 13, 2012, 06:37:44 PM »

I thought there were lots of moose in Norway? Build a treestand in a moose area and call them in!
EEE eroooooooahhhh! (cow call,lol) Love your work!

runastav · « **Reply #19 on:** October 14, 2012, 12:49:06 PM »

Hi guys, and thank you Leatherbelly! All small and big gamehunting is regulated by laws here in Norway

The sideplate made and inlet.
Runar

raszpla · « **Reply #20 on:** October 14, 2012, 01:56:35 PM »

nicely.

runastav · « **Reply #21 on:** October 16, 2012, 07:29:10 PM »

Hi guys, and thank you raszpla!Ramrod pipes made and the stock is formed, final sandig and muzzle cap next

and then the fun begin

Runar

D. Taylor Sapergia · « **Reply #22 on:** October 16, 2012, 07:49:54 PM »

You've done a very credible job on your Leman rifle. I love the use of the plain maple stock, and your workmanship is excellent.

multifasciatus · « **Reply #23 on:** October 17, 2012, 04:57:31 PM »

Hi

Not many weeks ago i saw this rifle in your workshop it was just a 2x4 piece of lumber with a barrel and a plastic bag of parts, ,
Impressive Runastav

runastav · « **Reply #24 on:** October 19, 2012, 05:42:59 PM »

Hi guys! and thank you Taylor and AJ!
Muzzle cap made and rivet in place

Runar

News:

Author Topic: Henry E. Leman part kit (Read 18055 times)

MarkEngraver

BartSr

cheyenne

greybeard

woodburner

Vomitus

raszpla