Author Topic: pair of pistols - Reconstruction - 1620 (Read 20022 times)

raszpla · « **on:** October 20, 2012, 12:28:04 AM »

I do not use Parts wheellock - steel castings.
I use rolled and forged steel . during the documentary, will demonstrate what kind of steel is suitable for individual elements wheellock, and that applies heat and chemical treatment (carburizing).
it will be a lot of work - you have to be patient

Greetings to all

Rolf · « **Reply #1 on:** October 20, 2012, 12:52:55 AM »

Thank you.

I look really forward to following this thread!!

Best regards
Rolf

raszpla · « **Reply #2 on:** October 20, 2012, 10:51:49 AM »

I use rolled carbon steel and alloy steel. The reason why this type of steel used :

1. We can make any mechanism wheellock.
2. the possibility of selecting appropriate mechanical properties of steel
3. opportunity to improve carbon steel enriching
4. the possibility of using the original, old locksmith techniques
5.the possibility of forging steel

1. + 2. + 3. + 4. + 5. = very large resistance and durability, mechanism components.great satisfaction with the work done

You must have in his workshop, basic locksmith tools and basic blacksmith tools. you will need a furnace for steel ( forging, carburizing ). These requirements can be achieved in a simple manner.

Rolf · « **Reply #3 on:** October 20, 2012, 12:23:21 PM »

What alloy steel? How much carbon in the carbon steel?

Best regards
Rolf

raszpla · « **Reply #4 on:** October 20, 2012, 12:28:32 PM »

I will explain all of these parameters, showing the specific elements

do you understand?

raszpla · « **Reply #5 on:** October 20, 2012, 12:41:21 PM »

some parts have special requirements, the parts are subjected to great loads.
I want to tell you gradually and accurately. I do not speak English. of patience

Rolf · « **Reply #6 on:** October 20, 2012, 02:46:39 PM »

Ok, thanks

Best regards
Rolf

4ster · « **Reply #7 on:** October 20, 2012, 04:24:15 PM »

Only if Raszpla thinks this is a good idea:

Is there someone on this site that can translate from Polish into English and back to Polish so that Raszpla does not have to rely on an internet translator? Imagine what our questions look like when a robot has translated them into Polish! A person with gun building experience is going to do a better job than an internet robot. It would lighten Raszpla's work load a bit.

I am looking forward to watching this topic, thank you Raszpla.

Long Ears · « **Reply #8 on:** October 20, 2012, 05:19:37 PM »

Raszpla,

Thanks for taking the time to explain the process in such detail. I'm looking forward to learning from you again. I've been reading a bunch about metalurgy and am slowly getting it. This will really help me in my quest. Thanks, Bob

Eric Smith · « **Reply #9 on:** October 20, 2012, 05:25:16 PM »

This pistol is similar to what might have been brought to Jamestown, Va. I' ll be following this one for sure.

Acer Saccharum · « **Reply #10 on:** October 20, 2012, 05:28:51 PM »

This is a case where form follows function. The lock mechanism dictates the form of the gun, the hand dictates the shape of the grip, all support the barrel with the purpose of sending a projectile enemy-ward. A lovely piece of engineering and art with deadly undertones. Fabulous paradox.

raszpla · « **Reply #11 on:** October 20, 2012, 08:17:48 PM »

raszpla · « **Reply #12 on:** October 20, 2012, 08:35:41 PM »

lock plate can be made of steel at least 0.20% of carbon , but it is essential after work carburet steel

raszpla · « **Reply #13 on:** October 21, 2012, 08:56:13 PM »

raszpla · « **Reply #14 on:** October 21, 2012, 09:35:15 PM »

raszpla · « **Reply #15 on:** October 21, 2012, 11:44:47 PM »

raszpla · « **Reply #16 on:** October 21, 2012, 11:56:06 PM »

raszpla · « **Reply #17 on:** October 22, 2012, 09:48:07 PM »

Long Ears · « **Reply #18 on:** October 23, 2012, 05:58:30 AM »

This guy is an artist with a file! Holy smokes! Bob

raszpla · « **Reply #19 on:** October 23, 2012, 06:20:53 PM »

raszpla · « **Reply #20 on:** October 24, 2012, 08:31:39 PM »

raszpla · « **Reply #21 on:** October 24, 2012, 09:23:48 PM »

raszpla · « **Reply #22 on:** October 25, 2012, 07:30:26 PM »

Chris Treichel · « **Reply #23 on:** October 25, 2012, 10:20:00 PM »

You mention that the point of the sear requires high hardness... I take it that the wheel will also be hardened where the sear comes in contact to reduce wear and provide a smooth contact?