Author Topic: Making a butt plate  (Read 8258 times)

Tommykid

  • Guest
Making a butt plate
« on: December 14, 2012, 06:59:53 PM »
I was given this rifle as a gift and have come close to finishing the cleaning/preservation. Here's some before/after pics:







The problem is it was missing the patch box cover and butt plate. I was able to make the patch box cover out of sheet brass, but am lost regarding the butt plate. I don't want to touch the wood. I got a too-large butt plate and have been trying to shape it to the existing space, but it's not going well, (mostly because I don't know what I'm doing). It might not be much, but this is only one of 10 known examples, so I don't want to start in-letting to fit a repro butt plate. Has anyone ever taken a wax impression of an inletted stock and then made a butt plate for that space? Not sure it's possible/practical/cost effective. Thanks in advance and I hope I put this post in the correct area.
Thanks,
Tom

Offline 490roundball

  • Sr. Member
  • ****
  • Posts: 377
Re: Making a butt plate
« Reply #1 on: December 14, 2012, 07:09:11 PM »
Reaves Goerhing has one he calls the "blob"  it can be shaped to fit an existing inlet

maybe you can make a template to fit the inlet - then reshape a blob with that

nice clean up job - hard to believe its the same gun
« Last Edit: December 14, 2012, 07:32:06 PM by 490roundball »
"It's a poor word that can't be spelt two ways" Tom Yeardley in Swanson's Silent Drum

Offline JPK

  • Sr. Member
  • ****
  • Posts: 384
Re: Making a butt plate
« Reply #2 on: December 14, 2012, 07:26:55 PM »
Nice work .
Is that a Russian model 1851 ?
A clear conscience is usually the sign of a bad memory.

Tommykid

  • Guest
Re: Making a butt plate
« Reply #3 on: December 14, 2012, 11:38:45 PM »
Reaves Goerhing has one he calls the "blob"  it can be shaped to fit an existing inlet

maybe you can make a template to fit the inlet - then reshape a blob with that

nice clean up job - hard to believe its the same gun

Thanks. I did make a paper template, then fitted one out of cardboard and transferred that to the butt plate I have. Limited talent and even less patience at the moment had me thinking about other options.
Tom

Tommykid

  • Guest
Re: Making a butt plate
« Reply #4 on: December 14, 2012, 11:42:13 PM »
Nice work .
Is that a Russian model 1851 ?

It's a variation of a first pattern Brunswick rifle recovered in Nepal in 2003. What makes this unusual is that the barrel is about 9" longer than the standard Brunswick. It's .70 and has 2-groove rifling.
Tom

Offline bgf

  • Hero Member
  • *****
  • Posts: 1403
Re: Making a butt plate
« Reply #5 on: December 15, 2012, 12:26:31 AM »
Is BP brass or steel?  It looks like you could just cut something out of 1/8" sheet and file it to shape/decorate.  I have made my last two LR buttplates out of steel, and I fit them to the rifle rather than the rifle to the buttplate (I hate tedious inletting, but like hammers). Yours looks like a flat sheet of brass is about all you need -- I don't see any return/comb extension?

This might do it:
http://www.trackofthewolf.com/Categories/PartDetail.aspx/0/1/SHEET-125-B

Offline smylee grouch

  • Hero Member
  • *****
  • Posts: 7883
Re: Making a butt plate
« Reply #6 on: December 15, 2012, 02:30:39 AM »
Hi Tommykid, I think BGF has it right, you could make one with some thicker sheet brass and if it dont look good make another as the brass isnt that expensive. Good luck which ever way you do it.

Offline D. Taylor Sapergia

  • Member 3
  • Hero Member
  • *
  • Posts: 12660
Re: Making a butt plate
« Reply #7 on: December 15, 2012, 03:25:28 AM »
I think you'll find that a Brunswick or Baker butt plate will fit very close.  Should be available from The Rifle Shoppe (TRS).

Remarkable job on the restoration.
D. Taylor Sapergia
www.sapergia.blogspot.com

Art is not an object.  It is the excitement inspired by the object.

Offline TPH

  • Hero Member
  • *****
  • Posts: 923
Re: Making a butt plate
« Reply #8 on: December 15, 2012, 04:24:39 AM »
Tommykid, good to see you here! You've done a great job on cleaning it up, keep up the good work.

While you can form one from heavy sheet brass, it may be beyond your tooling and the set of skills you have developed right now. I think that D. Taylor has made a good suggestion, try the TRS reproduction butt plate, it can be returned if it simply won't work.
T.P. Hern

Offline Jim Kibler

  • Hero Member
  • *****
  • Posts: 4462
    • Personal Website
Re: Making a butt plate
« Reply #9 on: December 15, 2012, 04:48:41 AM »
The butplate from TRS may work, but since it has been pulled from an existing butplate, there may be shrinkage such that it won't be useable.   It can sometimes be stretched by hammering, but in fitting to an existing stock, this may not work.  It's worth a shot though. 

Offline David Veith

  • Hero Member
  • *****
  • Posts: 611
    • davids painting
Re: Making a butt plate
« Reply #10 on: December 15, 2012, 05:18:59 AM »
Just a I deal if it is going to be brass. Make up a master out of bondo. and have it poured. I know someone that can do it.  ;D ;)
David
David Veith

Offline Jim Kibler

  • Hero Member
  • *****
  • Posts: 4462
    • Personal Website
Re: Making a butt plate
« Reply #11 on: December 15, 2012, 05:27:24 AM »
The shrinkage factor still applies.  If the bondo fits, the cast butplate won't.  Must be made larger.  Perhaps the bondo pattern could be made bigger?  Don't quite know how, but maybe.

Tommykid

  • Guest
Re: Making a butt plate
« Reply #12 on: December 15, 2012, 06:45:24 AM »
Tommykid, good to see you here! You've done a great job on cleaning it up, keep up the good work.

While you can form one from heavy sheet brass, it may be beyond your tooling and the set of skills you have developed right now. I think that D. Taylor has made a good suggestion, try the TRS reproduction butt plate, it can be returned if it simply won't work.

You obviously know me if you know that making a butt plate out of sheet brass is outside of my skill set  ;)  As for TRS butt plate....I've looked into it and it's too small. Besides having a longer barrel, these variants of the Brunswick have a larger stock all the way around. My best bet is probably to stay the current course and try and shape the repro butt plate I have.
Thanks,
Tom

Tommykid

  • Guest
Re: Making a butt plate
« Reply #13 on: December 15, 2012, 06:47:48 AM »
Just a I deal if it is going to be brass. Make up a master out of bondo. and have it poured. I know someone that can do it.  ;D ;)
David

It is brass....might be interesting to try it and see if perhaps it could aid in the shaping of the current brass butt plate I'm working on...
Tom

Offline Pete G.

  • Hero Member
  • *****
  • Posts: 2013
Re: Making a butt plate
« Reply #14 on: December 15, 2012, 05:32:53 PM »
Whatever route you chose to go, don't hurry the process. If you get impatient you may save a day or two, but you will regret it every time you pick up the rifle for years to come.

Offline D. Taylor Sapergia

  • Member 3
  • Hero Member
  • *
  • Posts: 12660
Re: Making a butt plate
« Reply #15 on: December 15, 2012, 08:34:58 PM »
Reeve's "blob" is sounding better all the time.  Filing brass is easy, and immensely satisfying.
D. Taylor Sapergia
www.sapergia.blogspot.com

Art is not an object.  It is the excitement inspired by the object.

Offline Acer Saccharum

  • Administrator
  • Hero Member
  • *
  • Posts: 19311
    • Thomas  A Curran
Re: Making a butt plate
« Reply #16 on: December 16, 2012, 12:30:06 AM »
Filing brass is easy.......

......only if the file is sharp!
Tom Curran's web site : http://monstermachineshop.net
Ramrod scrapers are all sold out.

Offline Gaeckle

  • Hero Member
  • *****
  • Posts: 1354
Re: Making a butt plate
« Reply #17 on: December 16, 2012, 02:19:23 AM »
The shrinkage factor still applies.  If the bondo fits, the cast butplate won't.  Must be made larger.  Perhaps the bondo pattern could be made bigger?  Don't quite know how, but maybe.


........here's how: make the pattern, spray it with spray adhesive, add aluminum foil....keep doing this to build up the area and then make the master from that. You would be basically wrapping the item in foil. Then contact Mr. Veith.