Author Topic: Trigger creep  (Read 7630 times)

Offline Nordnecker

  • Hero Member
  • *****
  • Posts: 1244
Trigger creep
« on: April 04, 2014, 01:20:10 AM »
I installed a simple trigger. It feels perfect when the gun isn't cocked- no creep, I can feel it against the sear. When the gun is cocked, it creeps to the sear- a lot. The pull is pretty light.  I can make/use another trigger if it will correct this. What should I do? Or what should I do differently? My pivot pin is about 1/4" in front of the sear.
"I can no longer stand back and allow communist infiltration, communist indoctrination and the international communist conspiracy to sap and impurify our precious bodily fluids."- Gen Jack T. Ripper

Offline mark esterly

  • Sr. Member
  • ****
  • Posts: 408
Re: Trigger creep
« Reply #1 on: April 04, 2014, 01:53:25 AM »
I had the same with my first build. solved it by capturing the sear bar in a hole in the trigger plate. it angles the trigger back some but I like the looks and the way it works.
living in the hope of HIS coming.......

Offline Don Getz

  • Hero Member
  • *****
  • Posts: 6853
Re: Trigger creep
« Reply #2 on: April 04, 2014, 06:21:55 AM »
The problem is the 1/4"......too close, I have found that just a little bit under 1/2" seems to work for me.  It is a thing that
requires some playing around, you have to work toward a happy medium.  If you make it real short, such as your 1/4" it is
a very light pull, but has creep.  If you pin it longer, 1/2", you will find that it pull somewhat harder, but has little or no
creep.........Don

Frenchy

  • Guest
Re: Trigger creep
« Reply #3 on: April 04, 2014, 07:41:41 AM »
Nordnecker,
When you say 'creep' only when the hammer is cocked, do you mean that there is slack that must be taken up before the trigger touches the sear?

Offline Nordnecker

  • Hero Member
  • *****
  • Posts: 1244
Re: Trigger creep
« Reply #4 on: April 04, 2014, 11:40:14 AM »
Yes. "Creep" might be the wrong word. When cocked, there is a bit of slack or slop that must be taken up before the trigger contacts the sear bar. When the lock is uncocked, there is a nice springy feel with no slop- a little side to side movement, though. After the slop is taken up, it trips the sear quickly. The pull weight might be a little light for a fowler, but the hammer won't fall from rapping the stock with a mallet, etc.
"I can no longer stand back and allow communist infiltration, communist indoctrination and the international communist conspiracy to sap and impurify our precious bodily fluids."- Gen Jack T. Ripper

Offline Acer Saccharum

  • Hero Member
  • *****
  • Posts: 19311
    • Thomas  A Curran
Re: Trigger creep
« Reply #5 on: April 04, 2014, 02:13:29 PM »
The only cure is to have a feather spring that holds the trigger against the sear.
Tom Curran's web site : http://monstermachineshop.net
Ramrod scrapers are all sold out.

Offline Bob Roller

  • Hero Member
  • *****
  • Posts: 9687
Re: Trigger creep
« Reply #6 on: April 04, 2014, 02:28:45 PM »
Nearly all of the best English guns and rifles have a lightly preloaded spring that holds the trigger release bar against the sear arm.Works fine.

Bob Roller

Offline Dphariss

  • Hero Member
  • *****
  • Posts: 9920
  • Kill a Commie for your Mommy
Re: Trigger creep
« Reply #7 on: April 04, 2014, 03:34:38 PM »
I installed a simple trigger. It feels perfect when the gun isn't cocked- no creep, I can feel it against the sear. When the gun is cocked, it creeps to the sear- a lot. The pull is pretty light.  I can make/use another trigger if it will correct this. What should I do? Or what should I do differently? My pivot pin is about 1/4" in front of the sear.

Too close to the sear unless the lock is well tuned. And then never are as they come.
Too close, less than 1/2" invariably produce creep.

Dan
He who dares not offend cannot be honest. Thomas Paine

Offline smart dog

  • Global Moderator
  • Hero Member
  • *
  • Posts: 7009
Re: Trigger creep
« Reply #8 on: April 04, 2014, 04:12:46 PM »
Hi Nordnecker,
What is the lock?  Take it out of the gun and bring it to half cock and then full cock.  Look at the position of the sear bar when the lock is at rest, then half cock, and then full cock.  Does it return to the same position on the lockplate each time or is it a little higher at full cock?  That may be the source of the problem not the pin position.  The simplest fix in that case is to install a very light flat spring on the triggerplate that holds the trigger against the sear regardless of how it moves.  That spring must be very light so not to interfere with the sear engaging the tumbler properly.  There are other fixes but they involve altering the sear or the tumbler, something I would not recommend unles you have a lot of experience.

dave 
"The main accomplishment of modern economics is to make astrology look good."

kaintuck

  • Guest
Re: Trigger creep
« Reply #9 on: April 04, 2014, 06:24:29 PM »
may be the lock~tip showed me 'good ones' and bad ones.....the sear bar should be slight movement, then back to where it starts.

Offline Acer Saccharum

  • Hero Member
  • *****
  • Posts: 19311
    • Thomas  A Curran
Re: Trigger creep
« Reply #10 on: April 04, 2014, 07:35:04 PM »
We should differentiate between trigger slop and trigger creep.

Slop: when the lock if cocked, or at rest, the trigger rattles fore and aft. (a light feather spring will fix this)

Creep: when the trigger is against the sear, your finger has to pull a long distance to get the sear nose out of the full cock notch. This could mean the full cock notch is too deep, too rough, or steel too soft. It could also mean the trigger pivot is pinned too close to the sear bar, geometry problem.
Tom Curran's web site : http://monstermachineshop.net
Ramrod scrapers are all sold out.

Vomitus

  • Guest
Re: Trigger creep
« Reply #11 on: April 04, 2014, 10:22:28 PM »
  I had a french fusil that had no slop,just a little creep. I got to like it. When I felt the creep, I knew exactly when it would trip.

Offline Acer Saccharum

  • Hero Member
  • *****
  • Posts: 19311
    • Thomas  A Curran
Re: Trigger creep
« Reply #12 on: April 04, 2014, 10:28:09 PM »
What's worse, a gun with a little creep or a little creep with a gun? (that's one for you, Roy)
Tom Curran's web site : http://monstermachineshop.net
Ramrod scrapers are all sold out.

Offline Nordnecker

  • Hero Member
  • *****
  • Posts: 1244
Re: Trigger creep
« Reply #13 on: April 05, 2014, 12:25:07 AM »
Well fellows, I really do appreciate all of the comments. I was under the impression that the sear would return to the same position during all of the settings. It seems to be a bit lower when at rest than when half/cocked. This is the slop I'm feeling. I understand how a feather spring would help, and will probably go that route.
I suppose the trigger pin could be moved forward at any time if it proves to be too light. I haven't had any time to fiddle with it today. I'll have a good look at it this evening.
"I can no longer stand back and allow communist infiltration, communist indoctrination and the international communist conspiracy to sap and impurify our precious bodily fluids."- Gen Jack T. Ripper

Offline Nordnecker

  • Hero Member
  • *****
  • Posts: 1244
Re: Trigger creep
« Reply #14 on: April 05, 2014, 12:47:51 AM »
Here's what I found. The sear is a little lower at rest than it is at half/cock position- not much, not even visible difference. So I wrapped a peice of electric tape around the sear bar just to see if it made a difference. The slop is gone.
So maybe I could find a little piece of metal tubing to go over the sear bar or maybe weld a little to the top of the trigger?
"I can no longer stand back and allow communist infiltration, communist indoctrination and the international communist conspiracy to sap and impurify our precious bodily fluids."- Gen Jack T. Ripper

Offline Acer Saccharum

  • Hero Member
  • *****
  • Posts: 19311
    • Thomas  A Curran
Re: Trigger creep
« Reply #15 on: April 05, 2014, 01:03:57 AM »
There should be a little play between the trigger and sear! Don't make it too tight, or you'll create an unsafe condition where the sear nose may not fully engage the full cock!

These are muzzleloader triggers, not Canjar triggers. There has to be a little slop.
Tom Curran's web site : http://monstermachineshop.net
Ramrod scrapers are all sold out.

Offline mark esterly

  • Sr. Member
  • ****
  • Posts: 408
Re: Trigger creep
« Reply #16 on: April 05, 2014, 03:03:50 AM »
acer
 
   would like to know how a spring to take up "slop" would be fashioned. I tried that before I captured the sear bar in the plate and as you stated it would not hold at full cock.
living in the hope of HIS coming.......

Offline Acer Saccharum

  • Hero Member
  • *****
  • Posts: 19311
    • Thomas  A Curran
Re: Trigger creep
« Reply #17 on: April 05, 2014, 04:25:30 AM »
Make this a very light spring so it just carries the weight of the trigger, and holds it against the sear. Note the spring contacts closer to the pivot, not at the very end of the trigger bar, this helps reduce the pressure on the sear. Too much pressure on the trigger would make the gun go off.



Tom Curran's web site : http://monstermachineshop.net
Ramrod scrapers are all sold out.

Offline Acer Saccharum

  • Hero Member
  • *****
  • Posts: 19311
    • Thomas  A Curran
Re: Trigger creep
« Reply #18 on: April 05, 2014, 04:32:21 AM »
Locks sold with the touted 'one position sear' are seldom exact. But you can fine tune this by working the notches so the sear bar is in exactly the same position for rest, half cock and full.

It's less work to add a feather spring.
« Last Edit: April 05, 2014, 04:33:02 AM by Acer Saccharum »
Tom Curran's web site : http://monstermachineshop.net
Ramrod scrapers are all sold out.

Offline Bob Roller

  • Hero Member
  • *****
  • Posts: 9687
Re: Trigger creep
« Reply #19 on: April 05, 2014, 03:52:21 PM »
A spring with upward thrust for this can easily be made from a piece of spring steel .025 thick.
As Acer said,too much upward pressure can create a dangerous lack of engagement at full cock.
I make springs nearly every day so see it as a non problem.
Also,unless you are experienced with remaking or modifying locks,I'd avoid the idea of altering the notches in the tumbler.
Bob Roller

Offline Nordnecker

  • Hero Member
  • *****
  • Posts: 1244
Re: Trigger creep
« Reply #20 on: April 05, 2014, 11:28:15 PM »
Acer's diagram was very helpful. I decided to try to pean the trigger a little to make it wider. I could always file it back down if it caused a problem. There is no more slop. I can rap the stock with a mallet and the hammer won't fall. As it turns out, the pivot is about 3/8" from the sear. I'm pretty happy with it now.
Thanks everyone.
"I can no longer stand back and allow communist infiltration, communist indoctrination and the international communist conspiracy to sap and impurify our precious bodily fluids."- Gen Jack T. Ripper

Offline Acer Saccharum

  • Hero Member
  • *****
  • Posts: 19311
    • Thomas  A Curran
Re: Trigger creep
« Reply #21 on: April 06, 2014, 04:33:25 AM »
I just caution you that with no slop between trigger and sear, it's possible that the trigger could be holding the sear from completely engaging the half-cock notch. Worse would be if the sear is now prevented from going completely in the full cock notch. When the stock wood shrinks, it's possible that the gun could be in an unsafe condition.

Safety is first and foremost.

Safety is why I prefer the feather spring, as it is very forgiving of many conditions.
Tom Curran's web site : http://monstermachineshop.net
Ramrod scrapers are all sold out.