« previous next »
Pages: [1] 2   Go Down

Author Topic: SxS project  (Read 13940 times)

Offline Longknife

  • Hero Member
  • *****
  • Posts: 2094
SxS project
« on: February 06, 2015, 08:28:14 PM »
I started this project a while back and have determined to get it done this year. My first SXS flinter. The barrels are 16 ga. X 30 inch Belgium b-loader barrels. They are 2 inches across at the breech so I will need a min. 2 3/4 inch wide stock blank....I think...any advice?...except..."don't"

[imghttp://][/img]  

[imghttp://][/img]

[imghttp://][/img]
« Last Edit: February 06, 2015, 08:28:51 PM by Longknife »
Logged
Ed Hamberg

Offline elk killer

  • Hero Member
  • *****
  • Posts: 1514
Re: SxS project
« Reply #1 on: February 06, 2015, 10:56:45 PM »
i have a piece of walnut thats 3" thick
never got around to making anything from it
be perfect for SXS
its plain no figure
Logged
only flintlocks remain interesting..

Offline KLMoors

  • Hero Member
  • *****
  • Posts: 859
Re: SxS project
« Reply #2 on: February 07, 2015, 04:33:09 AM »
I am planning a SXS build myself.

I called Dunlap and spoke to Daniel. Told him I needed a 2 3/4 inch piece of dense walnut. 3 days later I had a perfect piece, 2 7/8 inches thick, sitting on my front step.  It is American walnut, but this piece is real hard. Hopefully it will checker OK.

Try giving them a call and see if they have any more.
« Last Edit: February 07, 2015, 04:33:37 AM by KLMoors »
Logged

Offline D. Taylor Sapergia

  • Member 3
  • Hero Member
  • *
  • Posts: 12671
Re: SxS project
« Reply #3 on: February 07, 2015, 09:00:32 PM »
This brings back fond memories.  Great project, and coming along nicely.
Logged
D. Taylor Sapergia
www.sapergia.blogspot.com

Art is not an object.  It is the excitement inspired by the object.

Matabele

  • Guest
Re: SxS project
« Reply #4 on: February 07, 2015, 09:21:21 PM »
I love to see these kinds of builds, looks great! Please keep us posted on the progress if you are able.
Logged

Offline Captchee

  • Hero Member
  • *****
  • Posts: 768
Re: SxS project
« Reply #5 on: February 07, 2015, 11:04:43 PM »
 out standing !!
 i see you decided to go with interlocking plug design vs the smaller center rib and through bolt . Kuddooooos
Logged

Offline Longknife

  • Hero Member
  • *****
  • Posts: 2094
Re: SxS project
« Reply #6 on: February 08, 2015, 06:34:32 PM »
Elk killer, I sent PM about stock.


KLMoors, I will call Dunlop Monday, Thanks.

Captchee, As you can see I have TWO sets of breech plugs, and two sets of barrels that because I sure expect to FUBAR up one!!!!!!

Everybody else, I will keep you updated......





Logged
Ed Hamberg

Offline elk killer

  • Hero Member
  • *****
  • Posts: 1514
Re: SxS project
« Reply #7 on: February 08, 2015, 07:19:19 PM »
i never got it,
maybe try again?
Logged
only flintlocks remain interesting..

Offline Captchee

  • Hero Member
  • *****
  • Posts: 768
Re: SxS project
« Reply #8 on: February 08, 2015, 08:42:16 PM »
Quote
Captchee, As you can see I have TWO sets of breech plugs, and two sets of barrels that because I sure expect to FUBAR up one!!!!!!
you know i completely missed seeing that 2nd , smaller plug. judging by your work so far . i doubt you will screw it up
Logged

Offline Curtis

  • Hero Member
  • *****
  • Posts: 2338
  • Missouri
Re: SxS project
« Reply #9 on: February 09, 2015, 07:23:21 AM »
Looks like a great start on a really cool project!  I will enjoy following your progress, please keep us posted.

Curtis
Logged
Curtis Allinson
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Sometimes, late at night when I am alone in the inner sanctum of my workshop and no one else can see, I sand things using only my fingers for backing

Offline KLMoors

  • Hero Member
  • *****
  • Posts: 859
Re: SxS project
« Reply #10 on: February 10, 2015, 03:41:16 AM »
Longknife, I sent you a Pm but I'll also post the question here:

What size tap and die are you using for the 16ga barrels?
Logged

Offline Longknife

  • Hero Member
  • *****
  • Posts: 2094
Re: SxS project
« Reply #11 on: February 10, 2015, 05:57:41 PM »
KL, I used 3/4 -16....It cut real good in the. 16.8 mm (.66142 ) barrels,  lots of oil and cut it slow......The specs say you need a .6875 hole to tap 3/4 16 but the general tap size guides only give 75% full thread and I wanted a closer thread fit. I also used an adjustable die to make the plugs a little larger in dia. I now have a real good snug thread fit with no clearance at all...it worked for me...Ed   
Logged
Ed Hamberg

Offline D. Taylor Sapergia

  • Member 3
  • Hero Member
  • *
  • Posts: 12671
Re: SxS project
« Reply #12 on: February 10, 2015, 09:40:44 PM »
A 12 gauge will need a 7/8" x 14 tap and die.
Logged
D. Taylor Sapergia
www.sapergia.blogspot.com

Art is not an object.  It is the excitement inspired by the object.

Offline KLMoors

  • Hero Member
  • *****
  • Posts: 859
Re: SxS project
« Reply #13 on: February 11, 2015, 03:02:03 AM »
Hmmm, so did you cut the entire chamber off of the breech, making your cut just ahead of the forcing cone? 
Logged

Steve-In

  • Guest
Re: SxS project
« Reply #14 on: February 11, 2015, 03:17:02 AM »
It looks like you have a good start.  I would recess the breeches to give a slimmer profile.
Like this Manton..
http://www.sitemason.com/page/fvwTPq
Logged

Offline Longknife

  • Hero Member
  • *****
  • Posts: 2094
Re: SxS project
« Reply #15 on: February 11, 2015, 06:20:26 PM »
Quote from: KLMoors on February 11, 2015, 03:02:03 AM
Hmmm, so did you cut the entire chamber off of the breech, making your cut just ahead of the forcing cone? 

These were NOS barrels that had never been chambered.....


Quote from: Steve-In on February 11, 2015, 03:17:02 AM
It looks like you have a good start.  I would recess the breeches to give a slimmer profile.
Like this Manton..
http://www.sitemason.com/page/fvwTPq

That's the plan...


Logged
Ed Hamberg

Offline KLMoors

  • Hero Member
  • *****
  • Posts: 859
Re: SxS project
« Reply #16 on: February 12, 2015, 01:18:35 AM »
Got it. Thanks!
Logged

Offline Cody Tetachuk

  • Full Member
  • ***
  • Posts: 237
Re: SxS project
« Reply #17 on: February 13, 2015, 06:38:50 AM »
Using recessed breeches requires locks with specific frizzen geometry to be correct. Typical rifle locks will work (sort of) but you really do need the proper locks to go recessed. If using typical rifle locks, then a tapered breech would be more suitable.
Logged

pushboater

  • Guest
Re: SxS project
« Reply #18 on: February 13, 2015, 06:46:09 AM »
It's about time you did something with those barrels Ed! Of course, I can't say too much because I've had my Swivel Breech barrels back for at least 4 months now and haven't done a thing to them yet. Your Breech plugs look real nice though. Sounds like that Walnut stock would be about perfect. Since I moved to central Missouri last year I sure miss coming by and visiting with you. Keep us posted with some pics!
Logged

Offline Longknife

  • Hero Member
  • *****
  • Posts: 2094
Re: SxS project
« Reply #19 on: February 13, 2015, 06:42:35 PM »
Quote from: Cody Tetachuk on February 13, 2015, 06:38:50 AM
Using recessed breeches requires locks with specific frizzen geometry to be correct. Typical rifle locks will work (sort of) but you really do need the proper locks to go recessed. If using typical rifle locks, then a tapered breech would be more suitable.

Cody. Hoping to hear from you. What locks do you suggest?

Quote from: pushboater on February 13, 2015, 06:46:09 AM
It's about time you did something with those barrels Ed! Of course, I can't say too much because I've had my Swivel Breech barrels back for at least 4 months now and haven't done a thing to them yet. Your Breech plugs look real nice though. Sounds like that Walnut stock would be about perfect. Since I moved to central Missouri last year I sure miss coming by and visiting with you. Keep us posted with some pics!

Dave, I thought you had done "gone under" (HA). If you ever get up this way don't forget to stop by!!!!  P.S. Be careful, I think your warrant is still active!!!!
« Last Edit: February 13, 2015, 07:53:47 PM by Longknife »
Logged
Ed Hamberg

Offline D. Taylor Sapergia

  • Member 3
  • Hero Member
  • *
  • Posts: 12671
Re: SxS project
« Reply #20 on: February 13, 2015, 08:38:02 PM »
Good to have you posting again Cody.
Logged
D. Taylor Sapergia
www.sapergia.blogspot.com

Art is not an object.  It is the excitement inspired by the object.

Offline Cody Tetachuk

  • Full Member
  • ***
  • Posts: 237
Re: SxS project
« Reply #21 on: February 13, 2015, 10:27:05 PM »
I don't know of any commercial locks being offered that are suitable for recessed breeches other than castings taken from originals. For recessed breeches you want locks with a long throw from frizzen face to pivot pin so when the frizzen opens it lifts clear of the barrel. The Manton shown earlier shows this well. Here are a pair of locks that i was doing for a SXS that shows clearly how the high pivot point and long throw lifts the frizzen fairly straight up rather than up and back like a short throw rifle lock where the barrel would interfere with the frizzen unless relieved.
Logged

Offline Cody Tetachuk

  • Full Member
  • ***
  • Posts: 237
Re: SxS project
« Reply #22 on: February 13, 2015, 10:28:24 PM »
BTW, I had done a tutorial on breaching barrels for a SXS flint but have no idea what ever happened to it.
Logged

Offline WadePatton

  • Hero Member
  • *****
  • Posts: 5303
  • Tennessee
Re: SxS project
« Reply #23 on: February 13, 2015, 11:06:57 PM »
Quote from: Cody Tetachuk on February 13, 2015, 10:27:05 PM
I don't know of any commercial locks...

Totally diggin' that pan-out there swayin' in the cool breeze.  8)
Logged
Hold to the Wind

Offline gumboman

  • Sr. Member
  • ****
  • Posts: 263
    • Gumbocooking
Re: SxS project
« Reply #24 on: February 14, 2015, 06:24:10 AM »
Beautiful locks. Can I buy a couple?
Logged
Pages: [1] 2   Go Up
« previous next »