« previous next »
Pages: 1 [2]   Go Down

Author Topic: North Carolina Squirrel Rifle  (Read 13039 times)

Offline SingleMalt

  • Hero Member
  • *****
  • Posts: 613
  • One day I'll be considered a good builder.
Re: North Carolina Squirrel Rifle
« Reply #25 on: July 31, 2016, 05:33:53 PM »
It's coming along well.  What stain are you planning on using?  Lock polishing isn't bad.  You can do it at the kitchen table, in the A/C.  ;D
Logged
Never drink whisky that isn't old enough to vote.

"The penalty good men pay for indifference to public affairs is to be ruled by evil men."- Plato

"The Constitution shall never be construed to prevent the people of the United States who are peaceable citizens from keeping their own arms."

Offline David R. Pennington

  • Hero Member
  • *****
  • Posts: 2928
Re: North Carolina Squirrel Rifle
« Reply #26 on: July 31, 2016, 07:43:15 PM »
Funky Munky or Fishy Wishy, I like it either way, cool.
I am thinking about scraping my current one. Do you sand at all or go cold turkey and scrape only? Do you raise grain? Do you burnish? What is the sequence of events for a scraped finish?
Logged
VITA BREVIS- ARS LONGA

Offline Dennis Glazener

  • Administrator
  • Hero Member
  • *
  • Posts: 19487
    • GillespieRifles
Re: North Carolina Squirrel Rifle
« Reply #27 on: July 31, 2016, 10:08:59 PM »
Quote
I am now focusing on my favorite part of building a longrifle: lock polishing. 
How would you like to do a couple for me since you love it so much ;D I keep putting them off, I despise polishing them and hate browning them almost as bad!
Dennis
« Last Edit: August 01, 2016, 12:18:38 AM by Dennis Glazener »
Logged
"I never considered a difference of opinion in politics, in religion, in philosophy, as cause for withdrawing from a friend" - Thomas Jefferson

Offline Cory Joe Stewart

  • Hero Member
  • *****
  • Posts: 1862
    • My etsy shop
Re: North Carolina Squirrel Rifle
« Reply #28 on: August 01, 2016, 04:09:35 AM »
Quote from: Dennis Glazener on July 31, 2016, 10:08:59 PM
Quote
I am now focusing on my favorite part of building a longrifle: lock polishing. 
How would you like to do a couple for me since you love it so much ;D I keep putting them off, I despise polishing them and hate browning them almost as bad!
Dennis


Good luck with that.
Logged

Offline Cory Joe Stewart

  • Hero Member
  • *****
  • Posts: 1862
    • My etsy shop
Re: North Carolina Squirrel Rifle
« Reply #29 on: August 01, 2016, 04:10:57 AM »
Quote from: SingleMalt on July 31, 2016, 05:33:53 PM
It's coming along well.  What stain are you planning on using?  Lock polishing isn't bad.  You can do it at the kitchen table, in the A/C.  ;D

For my past couple of build I have been using the Homer Dangler stains that Jim Klein sells.  I have been happy with them.  I will probably go with the dark brown of that line.  I also use Chamber's oil finish as a follow up.

Coryjoe
Logged

Offline Cory Joe Stewart

  • Hero Member
  • *****
  • Posts: 1862
    • My etsy shop
Re: North Carolina Squirrel Rifle
« Reply #30 on: August 01, 2016, 04:13:08 AM »
Quote from: David R. on July 31, 2016, 07:43:15 PM
Funky Munky or Fishy Wishy, I like it either way, cool.
I am thinking about scraping my current one. Do you sand at all or go cold turkey and scrape only? Do you raise grain? Do you burnish? What is the sequence of events for a scraped finish?

Mark Elliot has always provided good information on scraping.  This one is a blend.  I struggle with scraping the transition areas.  You do raise the grain, but some argue that you only do it if needed.  I do burnish and do it after a couple of coats of oil.  You should check out the Mark Silver Traditional Gunstocking DVD from American Pioneer Video. 

Coryjoe
Logged

Offline Mike Brooks

  • Hero Member
  • *****
  • Posts: 13415
    • Mike Brooks Gunmaker
Re: North Carolina Squirrel Rifle
« Reply #31 on: August 08, 2016, 03:11:58 PM »
The original of this gun was at the Princeton Ill. gun show last week end. I saw it from an isle away but like an idiot I was in such a hurry I didn't get over to see it. ::)
Logged
NEW WEBSITE! www.mikebrooksflintlocks.com
Say, any of you boys smithies? Or, if not smithies per se, were you otherwise trained in the metallurgic arts before straitened circumstances forced you into a life of aimless wanderin'?

Offline Cory Joe Stewart

  • Hero Member
  • *****
  • Posts: 1862
    • My etsy shop
Re: North Carolina Squirrel Rifle
« Reply #32 on: August 09, 2016, 03:47:15 AM »
Quote from: Mike Brooks on August 08, 2016, 03:11:58 PM
The original of this gun was at the Princeton Ill. gun show last week end. I saw it from an isle away but like an idiot I was in such a hurry I didn't get over to see it. ::)

What an opportunity that would have been. 
Logged

Offline GANGGREEN

  • Sr. Member
  • ****
  • Posts: 373
Re: North Carolina Squirrel Rifle
« Reply #33 on: August 15, 2016, 06:12:52 PM »
I think that's the wood that I traded you for the Hawken parts, right?  I'm thrilled that it's going to look so nice.  I used a piece from the same board to send to Jim Kibler for one of his kits and it looks really nice too.  Nice work so far, be sure to update this thread as you near completion.
Logged

Offline Cory Joe Stewart

  • Hero Member
  • *****
  • Posts: 1862
    • My etsy shop
Re: North Carolina Squirrel Rifle
« Reply #34 on: August 16, 2016, 08:50:57 PM »
Quote from: GANGGREEN on August 15, 2016, 06:12:52 PM
I think that's the wood that I traded you for the Hawken parts, right?  I'm thrilled that it's going to look so nice.  I used a piece from the same board to send to Jim Kibler for one of his kits and it looks really nice too.  Nice work so far, be sure to update this thread as you near completion.

You are right.  That is it. 
Logged
Pages: 1 [2]   Go Up
« previous next »