« previous next »
Pages: [1]   Go Down

Author Topic: First build from a blank- made an ignorant move  (Read 2758 times)

Offline James

  • Hero Member
  • *****
  • Posts: 627
First build from a blank- made an ignorant move
« on: November 11, 2016, 09:55:55 PM »
I have successfully inlet a light weight 48" barrel and drilled the ramrod hole with good outcome.  I measured to get ready to remove excess wood from the sides of the forestock from muzzle to the fore-end.   I managed to lay my lines out wrong (shear stupidity)and because I was holding the stock in an upside down position to saw on the bandsaw,  I didn't notice until I'd cut 10" off the side of the blank at the muzzle end, that I was only leaving just over a 16th of an inch beside the barrel.  The barrel is inlet til the edge at the top of the side flat is flush with the top of the blank.  Once I cut away 1/2 of the wood to expose 1/2 of the side flat, it appears that there will be just under 1/8" of wood to shape for the profile beside the barrel at the muzzle end.  On the gun I just built, I removed wood until it only has 1/32" beside the barrel.  Will just under 1/8" be enough wood to shape the end of the forestock to make #53 in RCA 1 , or do I need to scrap the stock and start over?  I can leave more from there back, but short of gluing a piece on where I screwed up, I don't know how to fix this.
Logged
"Guard with jealous attention the public liberty. Suspect everyone who approaches that jewel. Unfortunately, nothing will preserve it but downright force. Whenever you give up that force, you are ruined... The great object is that every man be armed. Everyone who is able might have a gun." P.Henry

Online bob in the woods

  • Hero Member
  • *****
  • Posts: 4555
Re: First build from a blank- made an ignorant move
« Reply #1 on: November 11, 2016, 10:05:05 PM »
I mark my stock at 1/8th in , and then cut on the outside of the line, so a tad more wood to start, but I think you'll be OK
Logged

Offline Acer Saccharum

  • Hero Member
  • *****
  • Posts: 19311
    • Thomas A Curran
Re: First build from a blank- made an ignorant move
« Reply #2 on: November 11, 2016, 10:56:43 PM »
Work with what you've got.

We tend to make things too chunky these days, and you won't be doing that!
« Last Edit: November 11, 2016, 10:57:24 PM by Acer Saccharum »
Logged
Tom Curran's web site : http://monstermachineshop.net
Ramrod scrapers are all sold out.

Offline Mike Brooks

  • Hero Member
  • *****
  • Posts: 13415
    • Mike Brooks Gunmaker
Re: First build from a blank- made an ignorant move
« Reply #3 on: November 11, 2016, 11:52:20 PM »
You got no problem.
Logged
NEW WEBSITE! www.mikebrooksflintlocks.com
Say, any of you boys smithies? Or, if not smithies per se, were you otherwise trained in the metallurgic arts before straitened circumstances forced you into a life of aimless wanderin'?

Offline James

  • Hero Member
  • *****
  • Posts: 627
Re: First build from a blank- made an ignorant move
« Reply #4 on: November 12, 2016, 01:03:28 AM »
Thanks fellows,  you've made my day.
Logged
"Guard with jealous attention the public liberty. Suspect everyone who approaches that jewel. Unfortunately, nothing will preserve it but downright force. Whenever you give up that force, you are ruined... The great object is that every man be armed. Everyone who is able might have a gun." P.Henry

Offline Goo

  • Hero Member
  • *****
  • Posts: 708
Re: First build from a blank- made an ignorant move
« Reply #5 on: November 14, 2016, 04:02:52 PM »
What is RCA #53?
Logged
Opinions are expensive. Rich people rarely if ever voice their opinion.

Offline Keb

  • Hero Member
  • *****
  • Posts: 1193
  • south Ohio
Re: First build from a blank- made an ignorant move
« Reply #6 on: November 14, 2016, 04:10:38 PM »
RCA = Rifles of Colonial America. It's a picture book.
#53 is the 53rd gun from the front.
Logged
Pages: [1]   Go Up
« previous next »