« previous next »
Pages: [1] 2   Go Down

Author Topic: Which Lock to use  (Read 8359 times)

Torfinn

  • Guest
Which Lock to use
« on: July 30, 2017, 06:59:54 PM »
I am building my first Rifle and need advice on which Lock to use. I have

A. Verner stock from Pecatonica River that is inletted for a Colerain 38" B weight swamped barrel .50 cal. There is no other inletting

the above mentioned Colerain barrel

Colonial American Flint lock, one exposed screw version, by R. E. Davis

Large Siler Flint Lock

Would Like to use the R. E. Davis Lock but I am not sure it will work.  The Davis lock is much thicker than the Siler.
As this will be a Hunting rifle, exact historical accuracy is not required.  Any thoughts or suggestions would be much appreciated.

Thanks

Logged

Offline Mike Brooks

  • Hero Member
  • *****
  • Posts: 13415
    • Mike Brooks Gunmaker
Re: Which Lock to use
« Reply #1 on: July 30, 2017, 07:04:42 PM »
I'd probably go with the siler. That davis lock is going to be too big for a Verner gun.
Logged
NEW WEBSITE! www.mikebrooksflintlocks.com
Say, any of you boys smithies? Or, if not smithies per se, were you otherwise trained in the metallurgic arts before straitened circumstances forced you into a life of aimless wanderin'?

Offline sqrldog

  • Hero Member
  • *****
  • Posts: 986
Re: Which Lock to use
« Reply #2 on: July 30, 2017, 07:34:18 PM »
I agree with Mike use the deluxe Siler or I probably would use the Chambers Dale Johnson lock. Basically the same as a deluxe siler but the tail of the lock is a little lower which helps with lock placement in the wrist of the stock. The DJ lock is also a very quick lock. Tim
Logged

Torfinn

  • Guest
Re: Which Lock to use
« Reply #3 on: July 30, 2017, 09:44:16 PM »
Haven't seen a Dale Johnson Lock. It is not on the TOW site.
Logged

Offline SingleMalt

  • Hero Member
  • *****
  • Posts: 613
  • One day I'll be considered a good builder.
Re: Which Lock to use
« Reply #4 on: July 30, 2017, 10:50:59 PM »
I'd use one of Stan Hollenbaugh's locks.  He makes a straight and a curved.  Excellent locks, far better than anything you'll get mass produced.  http://www.stanhollenbaughgunsmith.com/page2.html
Logged
Never drink whisky that isn't old enough to vote.

"The penalty good men pay for indifference to public affairs is to be ruled by evil men."- Plato

"The Constitution shall never be construed to prevent the people of the United States who are peaceable citizens from keeping their own arms."

Offline sqrldog

  • Hero Member
  • *****
  • Posts: 986
Re: Which Lock to use
« Reply #5 on: July 30, 2017, 10:58:00 PM »
Try Muzzleloader Builders Supply, Stonewall Creek Outfitters, Jedidiah Starr Trading Co. for a Dale Johnson lock.
Logged

Offline wattlebuster

  • Hero Member
  • *****
  • Posts: 2088
Re: Which Lock to use
« Reply #6 on: July 30, 2017, 11:46:55 PM »
If you want a Dale Johnson lock go straight to the source.
Logged
Nothing beats the feel of a handmade southern iron mounted flintlock on a cold frosty morning

Offline moleeyes36

  • Hero Member
  • *****
  • Posts: 1443
Re: Which Lock to use
« Reply #7 on: July 31, 2017, 12:22:49 AM »
Quote from: wattlebuster on July 30, 2017, 11:46:55 PM
If you want a Dale Johnson lock go straight to the source.

Absolutely, go straight to Jim Chambers for the lock. 

Mole Eyes
Logged
Don Richards
NMLRA Field Rep, Instructor, Field Range Officer
NRA Chief Range Safety Officer

Offline sqrldog

  • Hero Member
  • *****
  • Posts: 986
Re: Which Lock to use
« Reply #8 on: July 31, 2017, 01:01:35 AM »
I agree Chambers is the place to get a lock. But the Dale Johnson locks sold by these vendors come out of the same batch as you get from Jim Chanbers he doesn't sell DJ  kits only assembked locjs which they buy from Jim same as you. They get a discount for volume. In fact the last DJ I bought Chambers was out and they recommended I try one of their vendors. The ones I named above. Tim
Logged

Offline flehto

  • Hero Member
  • *****
  • Posts: 3335
Re: Which Lock to use
« Reply #9 on: July 31, 2017, 01:20:00 AM »
The chambers Golden Age lock is shown below on my last build. Have also used the deluxe Siler and the Late Ketland. All these locks were used on Bucks County LRs. .....Fred

Logged

Offline Lucky R A

  • Hero Member
  • *****
  • Posts: 1628
  • In Costume
Re: Which Lock to use
« Reply #10 on: July 31, 2017, 07:47:28 AM »
     Fred's recommendation above is spot on.  I have handled a lot of original Bucks Co. guns and the majority had English trade locks similar to the Late Ketland, those that had Germanic locks were similar to the Siler family of locks.  I really like the Golden age lock for this application.  Your 38" barrel will make a nice hunting gun, but will miss in the H.C. department should be a B 44" to get close to correct. 

Ron
Logged
"The highest reward that God gives us for good work is the ability to do better work."  - Elbert Hubbard

cyrus1066

  • Guest
Re: Which Lock to use
« Reply #11 on: July 31, 2017, 08:27:34 AM »
I also would like a bit of  advice on 3 future builds,
 as am ordering the 3 locks in 1 order
 from Track
         -Rupp/Moll/S Long lock ?
         -M.Fiordney
         - Maryland school lock .......similar to Armstrong .
Any advice is appreciated .
Logged

Torfinn

  • Guest
Re: Which Lock to use
« Reply #12 on: July 31, 2017, 05:17:39 PM »
Quote from: Lucky R A on July 31, 2017, 07:47:28 AM
     Fred's recommendation above is spot on.  I have handled a lot of original Bucks Co. guns and the majority had English trade locks similar to the Late Ketland, those that had Germanic locks were similar to the Siler family of locks.  I really like the Golden age lock for this application.  Your 38" barrel will make a nice hunting gun, but will miss in the H.C. department should be a B 44" to get close to correct. 

Ron


I used to have a TVM Lancaster with a 42" barrell and standing on its heel it came almost up to my eyeballs. So I decided for Hunting I would like something a tad shorter.  ;D  And yes, Bucks County styling is what I am after although I do not intend to copy any particular maker.

I already have a large Siler Lock (have the Davis lock too) So I may end up going with that. But  I do Like the look of the Dale Johnson Lock and also the Golden Age lock looks good. Bought the Large Siler from Barbie at a Longrifle show about 14 years ago.  Hmmm... Tough decision.  Right now bills are much higher than availabe funds, LoL.  Don't expect tt hunt with it this year in any case. 
Logged

Offline flehto

  • Hero Member
  • *****
  • Posts: 3335
Re: Which Lock to use
« Reply #13 on: July 31, 2017, 08:37:22 PM »
I use the Dale Johnson locks  on the Lancasters and they really look like they belong. Can't understand though why a pronounced chamfer wasn't put on the lockplate.....it's not that hard to do but does look better than the nondescript whatever corner treatment they used. Could be used on a Bucks County.....Fred



« Last Edit: July 31, 2017, 08:40:44 PM by flehto »
Logged

Offline D. Taylor Sapergia

  • Member 3
  • Hero Member
  • *
  • Posts: 12671
Re: Which Lock to use
« Reply #14 on: August 01, 2017, 12:35:21 AM »
These gentlemen have made some great suggestions, and shown some equally splendid examples.  If I may, here's the lock I used for my own rendition of a A. Verner longrifle.  I used a Siler percussion lockplate and purchased stock parts from TOW in the way of a pan, cock, frizzen spring and such.  Using an enlargement of the lock I wanted to emulate, I simply filed until I had the best representation I could make.  Siler's internals including Chamber's replacement tumbler, to get the cock's full bent position as far rearward as possible, were used.  This is a splendid lock that gives fast ignition every time.
Don't settle for less than you can make or afford.



Logged
D. Taylor Sapergia
www.sapergia.blogspot.com

Art is not an object.  It is the excitement inspired by the object.

Offline scottmc

  • Hero Member
  • *****
  • Posts: 592
Re: Which Lock to use
« Reply #15 on: August 01, 2017, 01:40:44 AM »
Cyrus 1066, I sent you a pm to read.  If you are a lefty, let me know.  Hollenbaugh's Armstrong would be tough to beat if you are seriously considering building one.
Logged
Remember Paoli!

Offline Mike Brooks

  • Hero Member
  • *****
  • Posts: 13415
    • Mike Brooks Gunmaker
Re: Which Lock to use
« Reply #16 on: August 01, 2017, 04:34:04 AM »
Quote from: Torfinn on July 31, 2017, 05:17:39 PM
Quote from: Lucky R A on July 31, 2017, 07:47:28 AM
     Fred's recommendation above is spot on.  I have handled a lot of original Bucks Co. guns and the majority had English trade locks similar to the Late Ketland, those that had Germanic locks were similar to the Siler family of locks.  I really like the Golden age lock for this application.  Your 38" barrel will make a nice hunting gun, but will miss in the H.C. department should be a B 44" to get close to correct. 

Ron


I used to have a TVM Lancaster with a 42" barrell and standing on its heel it came almost up to my eyeballs. So I decided for Hunting I would like something a tad shorter.  ;D  And yes, Bucks County styling is what I am after although I do not intend to copy any particular maker.

I already have a large Siler Lock (have the Davis lock too) So I may end up going with that. But  I do Like the look of the Dale Johnson Lock and also the Golden Age lock looks good. Bought the Large Siler from Barbie at a Longrifle show about 14 years ago.  Hmmm... Tough decision.  Right now bills are much higher than availabe funds, LoL.  Don't expect tt hunt with it this year in any case.
That's why they called them "longrifles".
Logged
NEW WEBSITE! www.mikebrooksflintlocks.com
Say, any of you boys smithies? Or, if not smithies per se, were you otherwise trained in the metallurgic arts before straitened circumstances forced you into a life of aimless wanderin'?

Torfinn

  • Guest
Re: Which Lock to use
« Reply #17 on: August 01, 2017, 06:59:33 PM »
Quote from: Mike Brooks on August 01, 2017, 04:34:04 AM

That's why they called them "longrifles".

LOL  Guess I had that comin".   ;D  I do like Longrifles though. Half the reason I moved to Kentucky. My next rifle will be longer.
Logged

Offline Mike Brooks

  • Hero Member
  • *****
  • Posts: 13415
    • Mike Brooks Gunmaker
Re: Which Lock to use
« Reply #18 on: August 01, 2017, 10:29:11 PM »
Quote from: Torfinn on August 01, 2017, 06:59:33 PM
Quote from: Mike Brooks on August 01, 2017, 04:34:04 AM

That's why they called them "longrifles".

LOL  Guess I had that comin".   ;D  I do like Longrifles though. Half the reason I moved to Kentucky. My next rifle will be longer.
Just put a barrel stretcher on the one you got, you can usually stretch most of them near a foot or so.
Logged
NEW WEBSITE! www.mikebrooksflintlocks.com
Say, any of you boys smithies? Or, if not smithies per se, were you otherwise trained in the metallurgic arts before straitened circumstances forced you into a life of aimless wanderin'?

n stephenson

  • Guest
Re: Which Lock to use
« Reply #19 on: August 02, 2017, 12:19:50 AM »
Mike, I loaned my barrel stretcher out to someone a few years ago and ,I can`t remember who. Yours are the best I`ve ever used .   Are you still making them ? If not who makes the next best one`s to yours ? Some of the cheap China made ones change the bore diameter too much , especially when you stretch one a foot. Not so with yours. THE BEST!!! ::) ???
Logged

Offline jerrywh

  • Hero Member
  • *****
  • Posts: 8885
    • Jerrywh-gunmaker- Master Engraver FEGA.
Re: Which Lock to use
« Reply #20 on: August 02, 2017, 02:49:47 AM »
 Davis makes good locks but I don't like that lock at all.  I don't see any dimensions on it either.   i would take a siler any day.  I wouldn't do all that work for that savings. With that b  Weight barrel you need something slim.
Logged
Nobody is always correct, Not even me.

Offline Curtis

  • Hero Member
  • *****
  • Posts: 2338
  • Missouri
Re: Which Lock to use
« Reply #21 on: August 14, 2017, 03:03:17 AM »
Sorry I'm way late weighing in on this, I missed the thread when it was new.  There have been many very good suggestions for locks made so far!  Against some other opinions I would recommend the Davis Colonial lock for a Bucks county gun.  The lock is well designed and has plenty of meat on it making it a great candidate for reshaping.  Below are a couple photos of a Bucks County gun I built using the Davis Colonial - the original rifle had a lock of very similar size and styling.  If I were to do it again I would make a larger cock screw, the one that comes with it is too small for the large cock in my opinion.









Original rifle:



Curtis
« Last Edit: August 14, 2017, 08:48:53 AM by Curtis »
Logged
Curtis Allinson
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Sometimes, late at night when I am alone in the inner sanctum of my workshop and no one else can see, I sand things using only my fingers for backing

Torfinn

  • Guest
Re: Which Lock to use
« Reply #22 on: August 21, 2017, 03:48:47 AM »
Curtis,

Is the rifle you show built from a precarve or a blank?

And what shaping did you do on the davis lock. I like the way the lockplate stands proud of the stock,  it looks very good.
« Last Edit: August 22, 2017, 03:42:37 AM by Torfinn »
Logged

Torfinn

  • Guest
Re: Which Lock to use
« Reply #23 on: August 22, 2017, 03:35:07 AM »
Went to the CLA show in Lexington and Saw lots of fine rifles.  Picked up a disk from the KRA on upper bucks county rifles. Has mostly Verner and Shuler rifles on it. Still have not decided on the lock. but I have selected the sideplate. triggerguard and buttplate.
Logged

Offline Curtis

  • Hero Member
  • *****
  • Posts: 2338
  • Missouri
Re: Which Lock to use
« Reply #24 on: August 22, 2017, 05:34:35 AM »
Torfinn, it was built from a blank using a drawing of the original.

Curtis
Logged
Curtis Allinson
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Sometimes, late at night when I am alone in the inner sanctum of my workshop and no one else can see, I sand things using only my fingers for backing
Pages: [1] 2   Go Up
« previous next »