« previous next »
Pages: [1]   Go Down

Author Topic: Is this a gun part?  (Read 2970 times)

Offline Ky-Flinter

  • Global Moderator
  • Hero Member
  • *
  • Posts: 7496
  • Born in Kentucke, just 250 years late
Is this a gun part?
« on: December 02, 2017, 07:26:46 AM »
What is this?  Measures 5 13/16 in. long and 1 7/8 in. wide at widest point







-Ron
Logged
Ron Winfield

Life is too short to hunt with an ugly gun. -Nate McKenzie

Offline Curtis

  • Hero Member
  • *****
  • Posts: 2338
  • Missouri
Re: Is this a gun part?
« Reply #1 on: December 02, 2017, 07:51:52 AM »
My guess is probably not, looks too flat to me.  How thick is it? 

Curtis
Logged
Curtis Allinson
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Sometimes, late at night when I am alone in the inner sanctum of my workshop and no one else can see, I sand things using only my fingers for backing

Offline Dave B

  • Hero Member
  • *****
  • Posts: 3132
Re: Is this a gun part?
« Reply #2 on: December 02, 2017, 07:57:53 AM »
not from a gun but maybe from a case box set. The piece looks like it was made to be nailed down or riveted in place
Logged
Dave Blaisdell

Offline Mike Brooks

  • Hero Member
  • *****
  • Posts: 13415
    • Mike Brooks Gunmaker
Re: Is this a gun part?
« Reply #3 on: December 02, 2017, 04:29:51 PM »
It COULD be if you have some nails and a hammer.... ;)
Logged
NEW WEBSITE! www.mikebrooksflintlocks.com
Say, any of you boys smithies? Or, if not smithies per se, were you otherwise trained in the metallurgic arts before straitened circumstances forced you into a life of aimless wanderin'?

Offline flinchrocket

  • Hero Member
  • *****
  • Posts: 1750
Re: Is this a gun part?
« Reply #4 on: December 02, 2017, 04:59:01 PM »
Is that ole George Washington on their you suppose? To me the engraving looks like something you would expect to find on a military piece. Sword scabbard maybe?
Logged

Offline Ky-Flinter

  • Global Moderator
  • Hero Member
  • *
  • Posts: 7496
  • Born in Kentucke, just 250 years late
Re: Is this a gun part?
« Reply #5 on: December 02, 2017, 06:00:43 PM »
Quote from: Curtis on December 02, 2017, 07:51:52 AM
.....  How thick is it? 

Curtis

Thin.  About 1/16"

-Ron
Logged
Ron Winfield

Life is too short to hunt with an ugly gun. -Nate McKenzie

Offline D. Taylor Sapergia

  • Member 3
  • Hero Member
  • *
  • Posts: 12671
Re: Is this a gun part?
« Reply #6 on: December 02, 2017, 06:58:38 PM »
Perhaps an overlay for the end of a belt or strap, like a sword baldric or belt.  Very fine engraving...look at the rings around the holes!
Logged
D. Taylor Sapergia
www.sapergia.blogspot.com

Art is not an object.  It is the excitement inspired by the object.

lostinthewoods

  • Guest
Re: Is this a gun part?
« Reply #7 on: December 02, 2017, 10:08:00 PM »
These show up on ebay from time to time, usually called a Kentucky rifle "side plate"
Logged

Offline Levy

  • Hero Member
  • *****
  • Posts: 787
Re: Is this a gun part?
« Reply #8 on: December 02, 2017, 10:58:36 PM »
It looks acid etched to me instead of engraved.  James Levy
Logged
James Levy

54ball

  • Guest
Re: Is this a gun part?
« Reply #9 on: December 03, 2017, 12:21:57 AM »
 A peach colored leisure suit, a lava lamp and a spirit of 76 flag would match that perfectly.
Logged

Offline Cory Joe Stewart

  • Hero Member
  • *****
  • Posts: 1862
    • My etsy shop
Re: Is this a gun part?
« Reply #10 on: December 03, 2017, 02:08:30 AM »
I have seen those on ebay listed as a patchbox. 

Cory Joe Stewart
Logged
Pages: [1]   Go Up
« previous next »