« previous next »
Pages: [1]   Go Down

Author Topic: How thick plank need to be for a Hawken job  (Read 1800 times)

Offline mountainman70

  • Hero Member
  • *****
  • Posts: 2465
  • USAF vet 1971-1972 malmstrom afb,montana
How thick plank need to be for a Hawken job
« on: April 20, 2018, 05:26:01 AM »
I have a nice piece of curly that is 2 1/2 thick,plenty long for a f/s and enough for proper drop. With the early beavertail or the half moon such as on the Peterson rifle, can I get what I need with this board?I am planning to use a 1 1/8 x 36" 58 cal barrel .  8) 8) Thanks to all.have a good evening fellows. Cheers, Dave
Logged

Offline rich pierce

  • Administrator
  • Hero Member
  • *
  • Posts: 19524
Re: How thick plank need to be for a Hawken job
« Reply #1 on: April 20, 2018, 05:27:51 AM »
2” thick is enough for a Hawken.
Logged
Andover, Vermont

Offline mountainman70

  • Hero Member
  • *****
  • Posts: 2465
  • USAF vet 1971-1972 malmstrom afb,montana
Re: How thick plank need to be for a Hawken job
« Reply #2 on: April 20, 2018, 05:34:25 AM »
Thanks Rich, I thought it might be. This stock blank is so nice and curly I almost don't want to make a Hawken,but rather a SMR , but I have the stuff for this project,and rather use a slimmer blank to build a longrifle. Just hate to waste such wood.I am thinking early f/s Hawken sorta like the one on Gunsinternatnl,over in Virginia, I have a 2 piece buttplate,and most everthing to do this,using a long trigger and scroll guard.
Thanks again, Dave 8) 8)
Logged

Offline Dphariss

  • Hero Member
  • *****
  • Posts: 9920
  • Kill a Commie for your Mommy
Re: How thick plank need to be for a Hawken job
« Reply #3 on: April 20, 2018, 09:06:04 AM »
I would save the 2 1/2" for something where it was needed.

Dan

Logged
He who dares not offend cannot be honest. Thomas Paine

Offline Goo

  • Hero Member
  • *****
  • Posts: 708
Re: How thick plank need to be for a Hawken job
« Reply #4 on: April 20, 2018, 02:35:58 PM »
Build that hawken on a nice piece of straight grain walnut or cherry
Logged
Opinions are expensive. Rich people rarely if ever voice their opinion.

Offline mountainman70

  • Hero Member
  • *****
  • Posts: 2465
  • USAF vet 1971-1972 malmstrom afb,montana
Re: How thick plank need to be for a Hawken job
« Reply #5 on: April 20, 2018, 04:07:36 PM »
Yep, I believe I will save it for a longrifle. Just cant do it. Besides, after looking and measuring carefully, it would be marginal in the forend bottom.
Goo, I believe the cherry or very plain maple will get the call. I would like to do walnut, it just doesn't like me.
Thanks y'all. Dave F 8) 8)
Logged

Offline Scota4570

  • Hero Member
  • *****
  • Posts: 2393
Re: How thick plank need to be for a Hawken job
« Reply #6 on: April 20, 2018, 06:20:20 PM »
You will need some decent plans.  Track has some as does Stith.  Get them all, and plan it out.  Or, even draw your own plans from your parts.  Either way, you will know for sure then. 

Hey, who has correct Hawken nose caps? 
Logged

Offline mountainman70

  • Hero Member
  • *****
  • Posts: 2465
  • USAF vet 1971-1972 malmstrom afb,montana
Re: How thick plank need to be for a Hawken job
« Reply #7 on: April 20, 2018, 07:03:30 PM »
Thanks Scota, I have both sets of plans, and in good stead with many Hawken gurus on here,and elsewhere.
Have a goodun, Dave 8) 8)
Logged

Offline Herb

  • Hero Member
  • *****
  • Posts: 1709
Re: How thick plank need to be for a Hawken job
« Reply #8 on: April 21, 2018, 01:15:28 AM »
Scota4570:  Muzzleloader  Builders Supply.
Logged
Herb
Pages: [1]   Go Up
« previous next »