« previous next »
Pages: 1 [2]   Go Down

Author Topic: Manufaturing and Installing a Sliding Tumbler Safety on a Chambers Late Ketland  (Read 13617 times)

Offline Curtis

  • Hero Member
  • *****
  • Posts: 2338
  • Missouri
Re: Manufaturing and Installing a Sliding Tumbler Safety on a Chambers Late Ketland
« Reply #25 on: May 18, 2018, 04:15:00 AM »
Quote from: Ron Scott on May 17, 2018, 04:55:53 PM
Hi Curtis.  VERY NICE!  I could ask if any of the students from last years English Sorting Rifle seminar are interested in have you do theirs?  See you in a couple weeks.

Thanks Ron!  And that sounds like a great idea, have everyone bring their locks to Bowling Green and we can set up an assembly line.  Perhaps we can charge something like $49.95 a pop!   8) 

See you there!
Curtis
Logged
Curtis Allinson
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Sometimes, late at night when I am alone in the inner sanctum of my workshop and no one else can see, I sand things using only my fingers for backing

Offline Curtis

  • Hero Member
  • *****
  • Posts: 2338
  • Missouri
Re: Manufaturing and Installing a Sliding Tumbler Safety on a Chambers Late Ketland
« Reply #26 on: May 18, 2018, 04:34:35 AM »
Quote from: J. Talbert on May 17, 2018, 10:56:43 PM
Curtis,
Another fine project and documentation.
One question - with your soldering of the additional metal on the tumbler, was the soldering temp low enough to preserve the temper of the tumbler?

Can't wait for your next adventure!
Jeff

Jeff,  I used a vice as a heat sink and was careful not to get the setup any hotter than necessary.  I used SWIF solder paste which has a pretty low melting point but is quite strong in my experience.  Brownells sells a low temp silver solder paste that would probably work as well.

As for the next adventure - I am working on making a trigger guard for the same rifle, I will try to post some photos in the near future.


Robby and David, thanks for the kind words.  David, I am always working to find distractions for you, lol!  You should go ahead and make one of the safeties.

By the way, FYI everyone: David Rase did the barrel inlet and ramrod hole for the English sporting gun the lock belongs to.  Never have I seen a nicer job of it!  The English sporting gun was started in Ron Scott's class last year at the NMLRA Gunsmithing Seminar.  It was a fun class!

Curtis
« Last Edit: May 18, 2018, 04:55:42 AM by Curtis »
Logged
Curtis Allinson
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Sometimes, late at night when I am alone in the inner sanctum of my workshop and no one else can see, I sand things using only my fingers for backing

Offline Greg Pennell

  • Hero Member
  • *****
  • Posts: 1522
Re: Manufaturing and Installing a Sliding Tumbler Safety on a Chambers Late Ketland
« Reply #27 on: May 18, 2018, 06:00:09 AM »
Another super “how to”...this should definitely be added to the tutorial section.

Greg
Logged
“Let your gun therefore be the constant companion of your walks” Thomas Jefferson

Offline Rolf

  • Hero Member
  • *****
  • Posts: 1763
  • There's more than one way to skin a cat.
Re: Manufaturing and Installing a Sliding Tumbler Safety on a Chambers Late Ketland
« Reply #28 on: May 18, 2018, 10:45:16 AM »
Quote from: g.pennell on May 18, 2018, 06:00:09 AM
Another super “how to”...this should definitely be added to the tutorial section.

Greg
I agree. Would a shame to lose it.

Best regards
Rolf
Logged

Offline David Rase

  • Hero Member
  • *****
  • Posts: 4320
  • If we need it here, make it here. Charlie Daniels
Re: Manufaturing and Installing a Sliding Tumbler Safety on a Chambers Late Ketland
« Reply #29 on: May 18, 2018, 06:01:41 PM »


By the way, FYI everyone: David Rase did the barrel inlet and ramrod hole for the English sporting gun the lock belongs to.  Never have I seen a nicer job of it!  The English sporting gun was started in Ron Scott's class last year at the NMLRA Gunsmithing Seminar.  It was a fun class!

Curtis
[/quote]
Thank you Curtis for the endorsement on my barrel inletting.  I appreciate your kind words but you are not helping my transition from full time barrel inletter/part time rifle builder to full time rifle maker/part time barrel inletter.   ;D
David
Logged

Offline Curtis

  • Hero Member
  • *****
  • Posts: 2338
  • Missouri
Re: Manufaturing and Installing a Sliding Tumbler Safety on a Chambers Late Ketland
« Reply #30 on: May 19, 2018, 04:16:51 AM »
David, I often hop around on one foot - on the account of the other one is often stuck in my mouth!  ;)

Curtis
Logged
Curtis Allinson
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Sometimes, late at night when I am alone in the inner sanctum of my workshop and no one else can see, I sand things using only my fingers for backing

brokenflint

  • Guest
Re: Manufaturing and Installing a Sliding Tumbler Safety on a Chambers Late Ketland
« Reply #31 on: June 20, 2018, 05:17:30 PM »
I liked seeing the in person Curtis, again some nice work there and thanks for the photo tutorial.
Logged

Offline flatsguide

  • Hero Member
  • *****
  • Posts: 852
Re: Manufaturing and Installing a Sliding Tumbler Safety on a Chambers Late Ketland
« Reply #32 on: February 03, 2021, 04:54:55 AM »
Very nice and impressive work Curtis. Interesting work on the detent spring. I was wondering how that was handled.
Richard
Logged

Offline D. Taylor Sapergia

  • Member 3
  • Hero Member
  • *
  • Posts: 12671
Re: Manufaturing and Installing a Sliding Tumbler Safety on a Chambers Late Ketland
« Reply #33 on: February 04, 2021, 08:46:13 PM »
That's really nice work Curtis. 
Logged
D. Taylor Sapergia
www.sapergia.blogspot.com

Art is not an object.  It is the excitement inspired by the object.

Offline Curtis

  • Hero Member
  • *****
  • Posts: 2338
  • Missouri
Re: Manufaturing and Installing a Sliding Tumbler Safety on a Chambers Late Ketland
« Reply #34 on: February 06, 2021, 07:03:24 AM »
Thanks guys!

Curtis
Logged
Curtis Allinson
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Sometimes, late at night when I am alone in the inner sanctum of my workshop and no one else can see, I sand things using only my fingers for backing
Pages: 1 [2]   Go Up
« previous next »