Author Topic: Building a Gillespie Rifle cal 50 (Read 12491 times)

runastav · « **Reply #25 on:** November 20, 2018, 12:59:09 PM »

Hi all! And Craig Wilcox yes I do

Lock inletted, With one Lock screw like Dennis say. And I must thank Dennis for all information so far in my trying to build this Gillespie rifle as correct as possible!

Runar

short funny published poems

tupac analysis

runastav · « **Reply #26 on:** November 21, 2018, 07:31:01 PM »

Hi Guys! So its the set trigger, beginn With the triggerplate the EASY way ;)You see the trigger holes is of senter from the lock plate why I think Dennis must explane

Runar

runastav · « **Reply #27 on:** November 23, 2018, 01:08:53 PM »

Hi All! Dennis think the triggers are filed from flat thick iron not forged. We found a errol/missing part on the originaltriggers I try to copy Sharp-sighted will see it

Make the triggers from 6mm plate.
Runar

Craig Wilcox · « **Reply #28 on:** November 23, 2018, 03:44:19 PM »

Coming along nicely indeed! And I see you penciled in the missing screw.
Yesterday was our "Thanksgiving Day", which dates back to the 17th century. Do you have such a day in Norway? It is giving thanks for all the good things in our life, and traditionally we bake a turkey. We had about 30-35 people at my daughter's house, lots of grand children and great grand children for me to play around with.

runastav · « **Reply #29 on:** November 23, 2018, 05:57:42 PM »

Hi all, and thank you Craig Wilcox! No we dont have this day here in Norway, but we have taken after you the Black Friday today! The wife been out all day shopping phhuuu. Yes you right missing setscrew, but one more impoten part is the missing bit on the front trigger for just this screw ;)So I have to make a new front trigger when we discover it.
Runar

Craig Wilcox · « **Reply #30 on:** November 23, 2018, 08:52:41 PM »

Now Runar, you know how much you love to tinker with things like this set trigger system. So you get to have a wee bit more fun making another trigger. If you hated doing the work, you would have stuck in a Davis trigger already made!

I do get a kick out of seeing you "cut" the piece out with your 1/16" drill bit. If you are a bit ham-handed (clumsy) like me, you must buy them by the dozen!

Be good, and perhaps Sinter Klaus will come visit!!

runastav · « **Reply #31 on:** November 28, 2018, 01:14:14 PM »

Hi Guys! and thank you Craig Wilcox! Lotts of filing on that triggers, I use a broken RB mainspring for the master spring and cut from a clock spring (Thank you Norleif) for the front trigger.Folks, when inlett how long from the sear will you have the front trigger on this set trigger?
Runar

ammonium sulphate production

runastav · « **Reply #32 on:** December 03, 2018, 01:28:04 PM »

Hi All! Trigger inlet and it Works perfect ;)Sear between the triggers.
Runar

Greg Pennell · « **Reply #33 on:** December 03, 2018, 04:05:18 PM »

Beautiful work on those triggers, they capture the Gillespie look perfectly! I regret not building mine from scratch.

Greg

runastav · « **Reply #34 on:** December 07, 2018, 07:31:50 PM »

Hi all! And thank you Greg! Triggergard in Place 2 Wood screws , very litle Place for triggerfinger
Runar

Marcruger · « **Reply #35 on:** December 08, 2018, 01:21:51 AM »

Hi Runar,

<<<very litle Place for triggerfinger
Runar>>>

I was told by an oldtimer that the front trigger was pressed on the side of the trigger with the tip of the finger to release it. I am guessing that this actually meant sideways and rearward pressure with the finger tip (45 degree angle pressure?). With that motion, you wouldn't need much room in the trigger guard. I don't press the trigger that way, but I do release the front trigger with just the tip of my index finger. Not much pressure is needed.
Great job on the triggers! God Bless, and best wishes, Marc

Dennis Glazener · « **Reply #36 on:** December 08, 2018, 07:39:01 AM »

Runar,
Sorry I misunderstood your question about finger room. Marcruger is correct about the front trigger. Its my understanding that these rifles were made that way to keep a person from jerking the front trigger. The are meant to be fired by the side of the index finger. I have seen them where you could not physically get you finger through the guard due to closeness of the front trigger to the trigger guard bow. Try firing it with the side of your index finger tip.
Dennis

Daryl · « **Reply #37 on:** December 08, 2018, 10:17:10 PM »

Interesting, Dennis. That is how I operate the set trigger on my .36 cal. rat rifle.
It is so finely set, one must be VERY careful.

runastav · « **Reply #38 on:** December 12, 2018, 01:08:41 PM »

Hi and thank you guys! Butt plate , LOP 13-1/2" drop heel 3-5/8" Yes I know I take a shortcut

Runar

alumina vs aluminum oxide

runastav · « **Reply #39 on:** December 14, 2018, 02:52:59 PM »

Hi Guys! I rough shape the Stock after photos, is there anything I must change to get it more Gillespie style?
Runar

Dennis Glazener · « **Reply #40 on:** December 14, 2018, 04:27:16 PM »

Runar,
Looks like you have done a fine job on this rifle. The drawing you used was made from an original rifle by Harvey Gillespie Harvey used grease holes on some rifles and not on others so you might consider adding an oval grease hole. One thing we did not discuss is the unique stamps most of the Gillespies used in their barrels. If interested in these let me know and I will send photos.
Dennis

Dennis Glazener · « **Reply #41 on:** December 14, 2018, 04:29:27 PM »

Oops, forgot to ask if you wish to use a side plate or washer.
Dennis

runastav · « **Reply #42 on:** December 14, 2018, 05:48:41 PM »

Thank you Dennis! Yes, please send me innformation about oval grease hole, stamps, sideplate and we take the forestock at last.Was the ramrodpipes pinned or bent innside under the barrel? A german wheellock rifle I made years ago from a original they are bent inside

Runar

Craig Wilcox · « **Reply #43 on:** December 14, 2018, 11:26:46 PM »

Coming along nicely, Runar. I was surprised that you wrote the heel drop in inches, instead of millimeters! 88.9 mm, I think!
Really liking your attention to detail - and Dennis is a great advisor for you.

Dennis Glazener · « **Reply #44 on:** December 15, 2018, 02:52:07 AM »

Quote from: runastav on December 14, 2018, 05:48:41 PM

Thank you Dennis! Yes, please send me innformation about oval grease hole, stamps, sideplate and we take the forestock at last.Was the ramrodpipes pinned or bent innside under the barrel? A german wheellock rifle I made years ago from a original they are bent inside
Runar

Runar,
Will get the photos to you tomorrow, the pipes were pinned.
Dennis

Curtis · « **Reply #45 on:** December 15, 2018, 08:12:37 AM »

The rifle is looking great, Runar! Nice job on the triggers also.

Curtis

runastav · « **Reply #46 on:** December 17, 2018, 03:17:29 PM »

Hi All! And thank you folks!Craig Wilcoks, all books and etc I have is in English see the yeardstick laying on my nice cleane bench it have both inches and mm

the toeplate.
Runar

names of michael jackson's children

runastav · « **Reply #47 on:** December 19, 2018, 04:32:27 PM »

Hi All! Oval grease hole
Runar

symbol for nitrate

dogcreek · « **Reply #48 on:** December 19, 2018, 09:13:45 PM »

Great build and great pictures, Runar!

runastav · « **Reply #49 on:** December 21, 2018, 02:00:49 PM »

Hi all! and thank you dogcreek! Half moon sideplate

Runar

aluminum sulfate in food

News:

Author Topic: Building a Gillespie Rifle cal 50 (Read 12491 times)