Author Topic: Cleaning smaller bores with tow?  (Read 2251 times)

Offline Skychief

  • Hero Member
  • *****
  • Posts: 650
Cleaning smaller bores with tow?
« on: March 06, 2019, 02:45:45 AM »
I've never used tow for bore cleaning, regardless of caliber, rifled or smoothbore.

Is tow very useful in the smaller bores, say 32-45 caliber? In other words, is much to be gained by its use compared to jag/patch cleaning? It seemed I most often read about using tow in bigger bored smoothbores.

Best regards, Skychief.

Offline mark esterly

  • Sr. Member
  • ****
  • Posts: 404
Re: Cleaning smaller bores with tow?
« Reply #1 on: March 06, 2019, 04:24:57 PM »
i like it better than patches in my .32 rice squirrel barrel.
living in the hope of HIS coming.......

Offline WadePatton

  • Hero Member
  • *****
  • Posts: 5277
  • Tennessee
Re: Cleaning smaller bores with tow?
« Reply #2 on: March 06, 2019, 05:11:20 PM »
I don't see how it would be significantly different in the smaller bores, but have actually only used it in 54.  I'll need another worm (not complicated to make or buy) and try to use it in every bore I ever shoot again. 

But I cannot say that I have used it in small bores already.

Hold to the Wind

Offline mark esterly

  • Sr. Member
  • ****
  • Posts: 404
Re: Cleaning smaller bores with tow?
« Reply #3 on: March 07, 2019, 03:35:50 AM »
the barrel i referenced has round bottom grooves.  the tow fills the grooves better than a cleaning patch without fear of getting stuck in the barrel like a patch that is just a tad too big would.
living in the hope of HIS coming.......

Daryl Pelfrey

  • Guest
Re: Cleaning smaller bores with tow?
« Reply #4 on: March 07, 2019, 02:17:04 PM »
Where can I get Tow from?

Offline Dennis Glazener

  • Administrator
  • Hero Member
  • *
  • Posts: 19361
    • GillespieRifles
"I never considered a difference of opinion in politics, in religion, in philosophy, as cause for withdrawing from a friend" - Thomas Jefferson

Turtle

  • Guest
Re: Cleaning smaller bores with tow?
« Reply #6 on: March 09, 2019, 12:57:45 AM »



My tow worm is too big for my .32. Where can I get one small enough?

Offline rich pierce

  • Administrator
  • Hero Member
  • *
  • Posts: 18940
Re: Cleaning smaller bores with tow?
« Reply #7 on: March 09, 2019, 02:04:57 AM »



My tow worm is too big for my .32. Where can I get one small enough?

Larry Callahan and some folks here too.
Andover, Vermont

Offline Mike from OK

  • Hero Member
  • *****
  • Posts: 1083
Re: Cleaning smaller bores with tow?
« Reply #8 on: March 10, 2019, 12:56:33 AM »
You could make some yourself if you were so inclined. The Irish gentleman in this video can be a little difficult to understand. But he gives a good presentation of the steps involved...



It looks like there's some labor involved but it doesn't appear to be highly complicated.

You could make your own linen for patches and use the remaining tow for cleaning up.

Mike

Offline Dave_Markowitz

  • Starting Member
  • *
  • Posts: 8
Re: Cleaning smaller bores with tow?
« Reply #9 on: March 10, 2019, 03:48:35 AM »
Turkey Foot Trading Company sells hemp tow. I have not used it for cleaning but a bird's nest made from it works well to start a fire from an ember on char cloth.
Dave Markowitz

Offline Pukka Bundook

  • Hero Member
  • *****
  • Posts: 3367
Re: Cleaning smaller bores with tow?
« Reply #10 on: March 10, 2019, 07:07:07 PM »
One other thought on using tow, (Which I do and like using!)

Colonel Peter Hawker suggested using cloth for cleaning with a Patent Breech,  as he says, there may be a risk of leaving bits of tow in the breech, and it could cause the powder to fire if a spark remains when loading the second time.

How real this problem is I can't say, but in theory he might be right.
It hasn't dampened my enthusiasm for tow though, but I do check to see there is nothing remaining in the breech before I load.

Offline WadePatton

  • Hero Member
  • *****
  • Posts: 5277
  • Tennessee
Re: Cleaning smaller bores with tow?
« Reply #11 on: March 10, 2019, 08:28:59 PM »
One other thought on using tow, (Which I do and like using!)

Colonel Peter Hawker suggested using cloth for cleaning with a Patent Breech,  as he says, there may be a risk of leaving bits of tow in the breech, and it could cause the powder to fire if a spark remains when loading the second time.

How real this problem is I can't say, but in theory he might be right.
It hasn't dampened my enthusiasm for tow though, but I do check to see there is nothing remaining in the breech before I load.

Don't you think a tiny bit of tow would be fully consumed in the first ignition event it was a party to?  That's my thinkin--not that I have any patent-breech guns or plans for one.
Hold to the Wind

Offline Pukka Bundook

  • Hero Member
  • *****
  • Posts: 3367
Re: Cleaning smaller bores with tow?
« Reply #12 on: March 11, 2019, 05:41:36 AM »
Wade,

Yes I believe myself that you are right.
 I was merely passing on what the old Colonel had to say in the 1830's.   
In Theory it could happen, but so could  a lot of other stuff.
The Colonel and his contemporaries loaded from a flask straight down the barrel, and that may be why a winking spark would be most unwelcome.
Mind you, a good few used the safety or "Fireproof" flasks, that old Durs Egg used to demonstrate in his shop, so there would be no real reason to worry if one of these types was being used.

All the best,
Richard.

Smokey Plainsman

  • Guest
Re: Cleaning smaller bores with tow?
« Reply #13 on: March 11, 2019, 12:09:07 PM »
Yet another reason (as if their weren’t plenty) to avoid patent breech guns!!

Hoping tow can be used in a .40 cal. I’d like to try some when my TVM gets “done bilt” as it were!!

Offline Pukka Bundook

  • Hero Member
  • *****
  • Posts: 3367
Re: Cleaning smaller bores with tow?
« Reply #14 on: March 11, 2019, 05:28:35 PM »
Smokey,
It will work fine if you have a tow worm of the right size.  I make mine to fit and they live in the patch -box.

Smokey Plainsman

  • Guest
Re: Cleaning smaller bores with tow?
« Reply #15 on: March 12, 2019, 06:10:58 AM »
Smokey,
It will work fine if you have a tow worm of the right size.  I make mine to fit and they live in the patch -box.

Thanks! Mine will wear a tallow's hole in the stock.

Offline Pukka Bundook

  • Hero Member
  • *****
  • Posts: 3367
Re: Cleaning smaller bores with tow?
« Reply #16 on: March 12, 2019, 05:29:31 PM »
Smokey,

Some oi makes long, and some oi makes short.....