« previous next »
Pages: [1]   Go Down

Author Topic: brass cap for pistol grip  (Read 1605 times)

Offline yip

  • Hero Member
  • *****
  • Posts: 1050
brass cap for pistol grip
« on: March 19, 2020, 09:05:19 PM »
 hope i'm correct but i'm looking for a brass cap for pistol grip ( Bucks County)
where can one be found?
Logged

Offline Craig Wilcox

  • Hero Member
  • *****
  • Posts: 2532
Re: brass cap for pistol grip
« Reply #1 on: March 19, 2020, 09:47:14 PM »
Logged
Craig Wilcox
We are all elated when Dame Fortune smiles at us, but remember that she is always closely followed by her daughter, Miss Fortune.

Offline Pennsylvania Dutchman

  • Sr. Member
  • ****
  • Posts: 341
Re: brass cap for pistol grip
« Reply #2 on: March 19, 2020, 11:51:45 PM »
I ordered the buttcap for my son's pistol from Cabin Creek. It may be appropriate for a Bucks County pistol.







Mark
Logged
Mark Poley

Offline yip

  • Hero Member
  • *****
  • Posts: 1050
Re: brass cap for pistol grip
« Reply #3 on: March 20, 2020, 01:46:41 AM »
Dutchman; beatiful job and thanks.
Logged

Offline bob in the woods

  • Hero Member
  • *****
  • Posts: 4555
Re: brass cap for pistol grip
« Reply #4 on: March 20, 2020, 03:22:12 AM »
You can always make one.  They aren't terribly difficult.
Logged

Offline yip

  • Hero Member
  • *****
  • Posts: 1050
Re: brass cap for pistol grip
« Reply #5 on: March 20, 2020, 03:27:08 AM »
Bob in the woods; please email me with ideas. thanks yip
Logged

Offline Joe Stein

  • Sr. Member
  • ****
  • Posts: 443
Re: brass cap for pistol grip
« Reply #6 on: March 20, 2020, 07:50:21 AM »
Logged

Offline Rolf

  • Hero Member
  • *****
  • Posts: 1764
  • There's more than one way to skin a cat.
Re: brass cap for pistol grip
« Reply #7 on: March 20, 2020, 12:27:14 PM »
Quote from: Joe Stein on March 20, 2020, 07:50:21 AM
Here you go: make your own.
https://americanlongrifles.org/forum/index.php?topic=32410.0

Thats for a spurred butcap. This is for the Kentucky buttcap. It's a lot easier to make.
https://americanlongrifles.org/forum/index.php?topic=6615.0

Best regards
Rolf
Logged

Offline curly

  • Full Member
  • ***
  • Posts: 117
  • In GOD we trust
Re: brass cap for pistol grip
« Reply #8 on: March 20, 2020, 03:32:05 PM »
Muzzleloaders Builders Supply specializes in pistols. They will fix you up. Use their e mail address on their web site for contact.

   curly
Logged

Offline Craig Wilcox

  • Hero Member
  • *****
  • Posts: 2532
Re: brass cap for pistol grip
« Reply #9 on: March 20, 2020, 05:30:16 PM »
Rolf, viewing your tutorial, I was wondering if a railroad spike might be used as a punch.  Cut the tip off square, and polish the head.  Seems like it might do the job.
Logged
Craig Wilcox
We are all elated when Dame Fortune smiles at us, but remember that she is always closely followed by her daughter, Miss Fortune.

Offline bob in the woods

  • Hero Member
  • *****
  • Posts: 4555
Re: brass cap for pistol grip
« Reply #10 on: March 20, 2020, 08:25:46 PM »
Yip,  I'm no expert, but all I've used to make a brass cap for a pistol is a hardwood block, and a gouge.
This gives me the indent to swage the brass into. Anneal the brass often, and trim as required. It's more time consuming than difficult. If you want a fancy gargoyle type cap,I believe that MBS is one supplier who can provide these. Hope this helps.
Logged

Offline yip

  • Hero Member
  • *****
  • Posts: 1050
Re: brass cap for pistol grip
« Reply #11 on: March 20, 2020, 09:04:48 PM »
 ordered from T.O.T.W. thanks to all that replied
Logged

Offline Rolf

  • Hero Member
  • *****
  • Posts: 1764
  • There's more than one way to skin a cat.
Re: brass cap for pistol grip
« Reply #12 on: March 21, 2020, 11:37:59 AM »
Quote from: Craig Wilcox on March 20, 2020, 05:30:16 PM
Rolf, viewing your tutorial, I was wondering if a railroad spike might be used as a punch.  Cut the tip off square, and polish the head.  Seems like it might do the job.

Could work if you rounded the corners so they don't dig into the brass.
If I was to make a punch, I'd use round Stock and turn one end domed.

Best regards

Rolf
Logged

Offline yip

  • Hero Member
  • *****
  • Posts: 1050
Re: brass cap for pistol grip
« Reply #13 on: March 21, 2020, 07:00:30 PM »
Pennsylvania Dutchman; where did you get your trigger guard?
Logged

Offline Pennsylvania Dutchman

  • Sr. Member
  • ****
  • Posts: 341
Re: brass cap for pistol grip
« Reply #14 on: March 21, 2020, 07:50:59 PM »
yip, I ordered it from T. O. T. W. It is the American flint pistol triggerguard # TG-AFP-B
Mark
Logged
Mark Poley

Offline yip

  • Hero Member
  • *****
  • Posts: 1050
Re: brass cap for pistol grip
« Reply #15 on: March 22, 2020, 02:25:19 PM »
 thanks Pa Dutchman: tryed to order their out of stock
Logged
Pages: [1]   Go Up
« previous next »