« previous next »
Pages: [1]   Go Down

Author Topic: adding a sprue cutter on a Dixie Gun Works scissor mold  (Read 7955 times)

wwpete52

  • Guest
adding a sprue cutter on a Dixie Gun Works scissor mold
« on: November 19, 2011, 04:36:25 AM »
Many of us have purchased the scissor type Dixie Gun Works over the years.  They are not bad molds at all.  The only negative thing about them is that they do not have a sprue cutter.  Several years ago I saw one on ebay that someone had added a sprue cutter.  I wish that I had paid closer attention to it.  Does anyone out there in casting ball land have any ideas how to do that? :)
Logged

Offline Dphariss

  • Hero Member
  • *****
  • Posts: 9920
  • Kill a Commie for your Mommy
Re: adding a sprue cutter on a Dixie Gun Works scissor mold
« Reply #1 on: November 19, 2011, 07:01:12 AM »
I would just buy a real bullet mould and save the trouble. I gave up on "bag moulds"  and hair straighteners when I was a teenager.

Dan
« Last Edit: November 19, 2011, 07:01:48 AM by Dphariss »
Logged
He who dares not offend cannot be honest. Thomas Paine

wwpete52

  • Guest
Re: adding a sprue cutter on a Dixie Gun Works scissor mold
« Reply #2 on: November 19, 2011, 11:08:55 PM »
Quote from: Dphariss on November 19, 2011, 07:01:12 AM
I would just buy a real bullet mould and save the trouble. I gave up on "bag moulds"  and hair straighteners when I was a teenager.

Dan

Thanks for your comment but I don't think I'll give up on it. 
Logged

Offline smokinbuck

  • Hero Member
  • *****
  • Posts: 3004
Re: adding a sprue cutter on a Dixie Gun Works scissor mold
« Reply #3 on: November 20, 2011, 12:58:09 AM »
Pete,
 I had one that a friend who is a machinist put a sprue cutter on. He machined a flat on one side, made the sprue cutter plate and screwed it onto one half of the mold with a stop pin on the other half.. Worked real well.
Mark
Logged
Mark

Offline Randy Hedden

  • Hero Member
  • *****
  • Posts: 2250
  • American Mountain Men #1393
Re: adding a sprue cutter on a Dixie Gun Works scissor mold
« Reply #4 on: November 20, 2011, 04:29:18 AM »
I did the same as Mark described.  Milled the top flat and made a sprue cutter plate and attached it to the mold just like on a modern commercial mold.  Works like a charm.  I have this scissors type mold because at the time I bought it I could not find any other supplier with a mold in the size I wanted.

Randy Hedden
« Last Edit: November 20, 2011, 04:30:12 AM by Randy Hedden »
Logged
American Mountain Men #1393

Offline Bill of the 45th

  • Hero Member
  • *****
  • Posts: 1436
  • Gaylord, Michigan
Re: adding a sprue cutter on a Dixie Gun Works scissor mold
« Reply #5 on: November 20, 2011, 06:31:33 AM »
Or you could contact Jeff Tanner moulds and order a separate sprue cutter for 3 pounds, that's about six bucks plus postage.  Way cheaper than machining drilling and tapping, and stop pins.  Jeff doesn't put cutters on his, you need to get his cutter separate.

Bill
Logged
Bill Knapp
Over the Hill, What Hill, and when did I go over it?

Offline Dphariss

  • Hero Member
  • *****
  • Posts: 9920
  • Kill a Commie for your Mommy
Re: adding a sprue cutter on a Dixie Gun Works scissor mold
« Reply #6 on: November 20, 2011, 08:22:06 AM »
I guess we could look at it from this point of view.
Add up the cost. Based on Brownells shop price survey. Its probably a 100+ dollar job at LEAST.
 Unless you can find someone to do all the machine work for free...

Dan
Logged
He who dares not offend cannot be honest. Thomas Paine

wwpete52

  • Guest
Re: adding a sprue cutter on a Dixie Gun Works scissor mold
« Reply #7 on: November 20, 2011, 01:56:21 PM »
Quote from: Dphariss on November 20, 2011, 08:22:06 AM
I guess we could look at it from this point of view.
Add up the cost. Based on Brownells shop price survey. Its probably a 100+ dollar job at LEAST.
 Unless you can find someone to do all the machine work for free...

Dan

My neighbor owns a machine shop.  I'm a blacksmith. We help each other a lot.
Logged

brobb

  • Guest
Re: adding a sprue cutter on a Dixie Gun Works scissor mold
« Reply #8 on: December 19, 2011, 03:54:04 AM »
« Last Edit: January 14, 2020, 05:57:06 AM by rich pierce »
Logged
Pages: [1]   Go Up
« previous next »