Author Topic: Inletting trick- or: how to gage your depth  (Read 15714 times)

Offline Acer Saccharum

  • Administrator
  • Hero Member
  • *
  • Posts: 19311
    • Thomas  A Curran
Inletting trick- or: how to gage your depth
« on: August 11, 2012, 07:27:35 PM »
When inletting a barrel, lock, etc, how do you know you're getting close to the bottom of the inlet?

I use inletting black, very dry, on an old toothbrush. You can't really see the film it applies, so it's not very messy. Maple is a dream, because it's so white, the least little bit of black shows up.



I know I'm getting close to the bottom of the inlet, but how close? I certainly don't want to take too much out from under the tang.

So roll up a little ball of silly putty, modeling clay, or old chewing gum, and lay it in the bottom of the channel. It's in the channel, near the breech, about 3/32 in diam.




Set barrel in place, as far as it will go. I use a soft mallet, then really set it with a piece of endgrain maple and a hammer, and also set the barrel against the breech, by endgrain and hammer at the muzzle.

Oh, baby, look how flat the little ball of clay is! I can see the tang needs just a touch of wood removed, oblique flats in the channel can be scraped a bit, and I'm there!

« Last Edit: January 13, 2020, 11:14:20 PM by rich pierce »
Tom Curran's web site : http://monstermachineshop.net
Ramrod scrapers are all sold out.

Offline Cory Joe Stewart

  • Hero Member
  • *****
  • Posts: 1838
    • My etsy shop
Re: Inletting trick
« Reply #1 on: August 12, 2012, 12:01:52 AM »
Thanks for this.  I have all kinds of trouble in this area.  This may help some.

Coryjoe

Offline Acer Saccharum

  • Administrator
  • Hero Member
  • *
  • Posts: 19311
    • Thomas  A Curran
Re: Inletting trick
« Reply #2 on: August 12, 2012, 12:08:21 AM »
Silly Putty can actually be measured with calipers and light touch.
Tom Curran's web site : http://monstermachineshop.net
Ramrod scrapers are all sold out.

Offline Eric Smith

  • Hero Member
  • *****
  • Posts: 775
Re: Inletting trick
« Reply #3 on: August 12, 2012, 01:21:35 AM »
Another nice tutorial. Hats off to you Tom. Nice inlet in the pic.
Eric Smith

Offline Acer Saccharum

  • Administrator
  • Hero Member
  • *
  • Posts: 19311
    • Thomas  A Curran
Re: Inletting trick
« Reply #4 on: August 12, 2012, 01:24:20 AM »
Thanks, Eric. After doing it 20 or 30 times, the inlets start getting better.  ;D
Tom Curran's web site : http://monstermachineshop.net
Ramrod scrapers are all sold out.

Offline D. Taylor Sapergia

  • Member 3
  • Hero Member
  • *
  • Posts: 12522
Re: Inletting trick
« Reply #5 on: August 12, 2012, 01:40:46 AM »
That inlet was obviously done by a professional using a machine.  Mere mortals cannot inlet like that!!
D. Taylor Sapergia
www.sapergia.blogspot.com

Art is not an object.  It is the excitement inspired by the object.

Offline mountainman70

  • Hero Member
  • *****
  • Posts: 2393
  • USAF vet 1971-1972 malmstrom afb,montana
Re: Inletting trick
« Reply #6 on: August 12, 2012, 02:01:35 AM »
Good Lord,acer,if I was a tiny person,I could measure and check the square of this work!!!hats off to ya!!Dave

Offline Acer Saccharum

  • Administrator
  • Hero Member
  • *
  • Posts: 19311
    • Thomas  A Curran
Re: Inletting trick
« Reply #7 on: August 12, 2012, 05:42:53 AM »
.... all done by machine, by one of those router bits that makes square inside corners...... >:(
Tom Curran's web site : http://monstermachineshop.net
Ramrod scrapers are all sold out.

Offline D. Taylor Sapergia

  • Member 3
  • Hero Member
  • *
  • Posts: 12522
Re: Inletting trick
« Reply #8 on: August 12, 2012, 05:57:34 AM »
...just as I thought!
D. Taylor Sapergia
www.sapergia.blogspot.com

Art is not an object.  It is the excitement inspired by the object.

Offline Topknot

  • Sr. Member
  • ****
  • Posts: 463
    • www.yahoo.com
Re: Inletting trick- or: how to gage your depth
« Reply #9 on: August 13, 2012, 12:35:52 AM »
Great Trick TOM,
Ishould of thunk of that.
TIM COMPTON, SR.

    layover to catch meddlers!

Offline Mike New

  • Full Member
  • ***
  • Posts: 131
Re: Inletting trick- or: how to gage your depth
« Reply #10 on: August 13, 2012, 02:47:13 AM »
Wow!! What clean inleting. It would be easier if you told us how you get the maple to grow around the barrel. Thanks, Mike 

Offline Dr. Tim-Boone

  • Global Moderator
  • Hero Member
  • *
  • Posts: 6534
  • I Like this hat!!
Re: Inletting trick- or: how to gage your depth
« Reply #11 on: August 13, 2012, 04:46:35 PM »
There is something bothersome about that...............

BTW my dentist gave me some strips of black and red paper he uses to determine the fit of teeth in the bite or the height/clearance of new crowns being mounted.  Very nice and clean  for testing the depth of inlets and fit of whatever you are inletting.... dentists have the neatest gadgets...
De Oppresso Liber
Marietta, GA

Liberty is the only thing you cannot have unless you are willing to give it to others. – William Allen White

Learning is not compulsory...........neither is survival! - W. Edwards Deming

Offline Cody Tetachuk

  • Full Member
  • ***
  • Posts: 237
Re: Inletting trick- or: how to gage your depth
« Reply #12 on: August 13, 2012, 04:54:18 PM »
That's a great idea Tom. Same concept as "plastigauge" used to measure bearing clearances except that the plastigauge has a scale where you measure the WIDTH after squeezing it to get the thickness/clearance. The stuff is cheap and comes in several thicknesses for different clearance ranges. http://www.plastigaugeusa.com/how.html