Author Topic: Tools/techniques for cutting incised lines  (Read 2225 times)

Offline Dstavlo

  • Starting Member
  • *
  • Posts: 6
Tools/techniques for cutting incised lines
« on: March 21, 2019, 08:20:20 PM »
Hello all,
I'm quite familiar with the tools and techniques used for cutting relief carving, but one thing that doesn't appear to have been discussed much is how incised lines are cut. Does anyone have any photos of the tools they use for this purpose or a brief description of how they do it?
Thanks,
David


Offline Dstavlo

  • Starting Member
  • *
  • Posts: 6
Re: Tools/techniques for cutting incised lines
« Reply #2 on: March 21, 2019, 08:38:11 PM »
Thank you for the links and sorry for belaboring the topic. I did search the forum before posting but didn't come across these posts. Perhaps my search terms were too specific. Anyway these are helpful thanks again.

Offline Hungry Horse

  • Hero Member
  • *****
  • Posts: 5565
Re: Tools/techniques for cutting incised lines
« Reply #3 on: March 22, 2019, 07:45:50 PM »
 Get Jack Brooks’s video on carving a stock. It’s the best I’ve seen. He incise carves a buttstock in a couple of hours. And, shows you how to sharpen the gouges as well.

  Hungry Horse

Turtle

  • Guest
Re: Tools/techniques for cutting incised lines
« Reply #4 on: March 22, 2019, 07:54:58 PM »
 as a novice, here's how I do it. I cut a deep line in the center of where I want it with an exacto knife, then I run a small veener down the line, repeating to get the depth I want. I then clean it up and make minor corrections with a curved V riffler.
« Last Edit: March 23, 2019, 02:25:53 AM by Turtle »

Offline Hungry Horse

  • Hero Member
  • *****
  • Posts: 5565
Re: Tools/techniques for cutting incised lines
« Reply #5 on: March 22, 2019, 11:36:56 PM »
Jack basically stabs it in with gouges with the proper radius. Then he goes back with the same gouges after it’s all been stabbed in once, and backs of a bit and widens, and flairs the cut.

  Hungry Horse

Offline Stophel

  • Hero Member
  • *****
  • Posts: 4532
  • Chris Immel
Re: Tools/techniques for cutting incised lines
« Reply #6 on: March 23, 2019, 04:02:52 AM »
I use the same "V" Parting tool for pretty much everything!  Incise and relief carving.   ;)
When a reenactor says "They didn't write everything down"   what that really means is: "I'm too lazy to look for documentation."

Offline Mike Brooks

  • Hero Member
  • *****
  • Posts: 13415
    • Mike Brooks Gunmaker
Re: Tools/techniques for cutting incised lines
« Reply #7 on: March 23, 2019, 03:10:20 PM »
I use the same "V" Parting tool for pretty much everything!  Incise and relief carving.   ;)
Ditto. I do some stabing too when it's convenient. STABBY STABBY STABBY.....ooops got carried away. :P
NEW WEBSITE! www.mikebrooksflintlocks.com
Say, any of you boys smithies? Or, if not smithies per se, were you otherwise trained in the metallurgic arts before straitened circumstances forced you into a life of aimless wanderin'?

Offline WadePatton

  • Hero Member
  • *****
  • Posts: 5303
  • Tennessee
Re: Tools/techniques for cutting incised lines
« Reply #8 on: March 23, 2019, 04:08:20 PM »
Thank you for the links and sorry for belaboring the topic. I did search the forum before posting but didn't come across these posts. Perhaps my search terms were too specific. Anyway these are helpful thanks again.

A word or two on successful searching:

Some search engines don't really work that good when they take -any- form of a word, a letter sequence, and return that in your results (as this one does). One way around that is to search "TITLES ONLY" but this is wholly dependent upon the posters to use GOOD titles with spellings correct.  And that is quite rare in these parts-possibly because very few understand how effective "title searching" can be and that it hinges on simple descriptive and accurate titles.   

I have found the quickest, most satisfying, alternative is to utilize an external search, where you limit the big search engine to any, or this particular site. With them you tend to use the site URL after the term "SITE:" , then a space, and the term/terms.

Thusly: Site:Americanlongrifles.org Golf  WHERE  "site:americanlongrifles.org" tells the search engine where to look, then a space and then your term/s-"Golf" in this example.  Everyone should try this one time-with a better term.

And other rules of combinations/exclusions can be used in a big search engine. Tired of getting results for XY when you only want X?  then search for "X -Y" and the Y results will all be eliminated. 

Little stuff.

Happy new searches. I use Bing, you use whatever you like.  HTH  ;)
Hold to the Wind

Offline t.caster

  • Hero Member
  • *****
  • Posts: 3729
Re: Tools/techniques for cutting incised lines
« Reply #9 on: March 23, 2019, 04:33:52 PM »
For incise and relief carving I use a palm length 2mm v tool I found in Japan. It is all done freehand, no mallet.







Example of incised carving with some relief work on recent work.



Tom C.

Offline rich pierce

  • Administrator
  • Hero Member
  • *
  • Posts: 19523
Re: Tools/techniques for cutting incised lines
« Reply #10 on: March 23, 2019, 05:49:05 PM »
Lots of different techniques and tools. I build so slowly I have to do a bunch of practice work before doing the real thing. Sharp tool plus practice will yield good cuts.  Now design is another thing!
Andover, Vermont