« previous next »
Pages: [1]   Go Down

Author Topic: Loading block drill size.  (Read 10305 times)

Offline Eric Krewson

  • Hero Member
  • *****
  • Posts: 2254
Loading block drill size.
« on: November 25, 2009, 06:51:27 AM »
I need to make a loading block for my new 54cal. I remember seeing a chart for the proper drill size for all calibers but cant find it through a search. What size drill do you guys use to make a 54 cal loading block? I have some nice osage, red oak burl and curly that would make now striking looking loading blocks.

Here is some of the burl wood in a bow tillering tool.

« Last Edit: November 25, 2009, 06:59:12 AM by Eric Krewson »
Logged

Offline Chuck Burrows

  • Hero Member
  • *****
  • Posts: 1218
    • Wild Rose Trading Company
Re: Loading block drill size.
« Reply #1 on: November 25, 2009, 09:48:08 AM »
Logged
Two roads diverged in a wood, and I,
I took the one less traveled by,
And that has made all the difference.

BrownBear

  • Guest
Re: Loading block drill size.
« Reply #2 on: November 25, 2009, 09:49:14 AM »
"Officially" the chart I've seen calls for a 35/64" bit.  But just try to find one at a decent price!  I had a 17/32" around and tried that.  It's real close, but requires just a bit of sanding with a piece of sandpaper wrapped around a pencil to get it right.  Kind of a file-to-fit situation, but it doesn't take much.
Logged

Offline PIKELAKE

  • Sr. Member
  • ****
  • Posts: 284
Re: Loading block drill size.
« Reply #3 on: November 25, 2009, 07:14:22 PM »
A couple of weeks ago I found that a 35/64 bit was a tad too small for a 530 ball and a patch. I think the patch was.015. Anyway,  I just reamed the holes with a rat tail file till the balls fit snug.
Logged
JOHN ZUREKI

Offline Dennis Glazener

  • Administrator
  • Hero Member
  • *
  • Posts: 19483
    • GillespieRifles
Re: Loading block drill size.
« Reply #4 on: November 25, 2009, 10:21:09 PM »
Not having a 35/64 inch bit I made my .54 cal loading block using a 9/16 (36/64) then I used a oil finish on the block, making sure to really soak the inside of the hole. I have been using it for 2 years with .530 balls and .015 patching and its still very tight, never lost a ball and I wear it around my neck and swings all around ;D
Dennis
 
« Last Edit: November 26, 2009, 01:02:55 AM by Dennis Glazener »
Logged
"I never considered a difference of opinion in politics, in religion, in philosophy, as cause for withdrawing from a friend" - Thomas Jefferson

Offline wmrike

  • Full Member
  • ***
  • Posts: 248
Re: Loading block drill size.
« Reply #5 on: November 25, 2009, 11:08:03 PM »
Guess I'm not that detail oriented.  I just drill a half inch hole and open it with a Dremel until I get the fit I like.  Gorgeous piece of wood.  With all that figure, be sure to leave enough stock so that a tight ball/patch combo won't spit it for you.  Be sure to show us the end product, eh?
Logged

Offline B.Habermehl

  • Hero Member
  • *****
  • Posts: 1688
Re: Loading block drill size.
« Reply #6 on: November 26, 2009, 12:18:37 AM »
The easiest thing to do is take a cheep speed bore bit, (you know the flat ones), and file it down as necessary to get it to drill the diameter hole that you want. A while back I made a set of these in  most of the popular calibers and was making a bunch of loading blocks to sell at the shoots on  my trade blanket.
   BJH
Logged
BJH

Offline davec2

  • Hero Member
  • *****
  • Posts: 2952
    • The Lucky Bag
Re: Loading block drill size.
« Reply #7 on: November 26, 2009, 05:24:21 AM »
It requires a bit of investment, but a few taper pin reamers of various sizes come in handy for a variety of hole size adjustment issues.  The ebony loading blocks below are for .32 and .50 cal round balls.  I drill the holes undersize and then use a taper pin reamer, from both sides, to precisely adjust the hole size to grip the ball (any size ball and any patch thickness) the way I want. 



I also use these reamers to open up the bores of cast ram rod pipes, etc.  The reamer in the photos below is a Number 8.  I use #s 7,8, & 9 the most and those three have been worth more than what they cost over the years in making hole adjustments quick, easy and precise.


« Last Edit: January 05, 2020, 06:38:12 AM by davec2 »
Logged
"No man will be a sailor who has contrivance enough to get himself into a jail; for being in a ship is being in a jail, with the chance of being drowned... a man in a jail has more room, better food, and commonly better company."
Dr. Samuel Johnson, 1780

Offline Brian

  • Hero Member
  • *****
  • Posts: 6364
Re: Loading block drill size.
« Reply #8 on: November 26, 2009, 04:52:42 PM »
Dave - your "casual" stuff just blows me away!   :o

Wild loading blocks and accessories.
Logged
"This is my word, and as such is beyond contestation"

Jefferson58

  • Guest
Re: Loading block drill size.
« Reply #9 on: November 28, 2009, 12:39:24 AM »
The tapered reamers look like a great idea for this and other projects. Out of curiosity, whose catalog are we viewing there?

Jeff
Logged

Offline davec2

  • Hero Member
  • *****
  • Posts: 2952
    • The Lucky Bag
Re: Loading block drill size.
« Reply #10 on: November 28, 2009, 01:27:05 AM »
Jeff,

Sorry, I meant to put that in my post.  The catalog is from McMaster Carr, but several of the machine tool houses will carry the standard taper pin reamers.
Logged
"No man will be a sailor who has contrivance enough to get himself into a jail; for being in a ship is being in a jail, with the chance of being drowned... a man in a jail has more room, better food, and commonly better company."
Dr. Samuel Johnson, 1780

Offline Tim Crosby

  • Administrator
  • Hero Member
  • *
  • Posts: 18386
  • AKA TimBuckII
Re: Loading block drill size.
« Reply #11 on: November 28, 2009, 11:27:08 PM »
 I with Brian, you make some of the Koolest stuff.

 Tim C.
Logged
Pages: [1]   Go Up
« previous next »