Author Topic: I need a lighter rifle  (Read 4222 times)

Offline Darkhorse

  • Hero Member
  • *****
  • Posts: 1663
I need a lighter rifle
« on: October 10, 2023, 11:34:34 AM »
So here I am turning 71 and a year ago I had a severe case of Spinal Stenosis which resulted in big boy back surgery. Of which I have yet to recover. And 2 weeks ago I had a heart attack of all things.
The result is my .54 flint is too heavy for me now.
I have shoulder problems which means I can't rasp or sandpaper to the extent of building another rifle.
So, just thinking here..... I do have a 40 Haines I built to hunt turkeys with. It has a Rice B barrel and is also too heavy in it's present form.
But I've been thinking about fitting a "B" 50 cal barrel to this rifle to reduce weight.
What problems am I getting into?
Has anybody done this before?
Will I cut enough weight to make it worthwhile?
This is the 40 I'm thinking about modifying.


American horses of Arabian descent.

Offline JLayne

  • Full Member
  • ***
  • Posts: 166
Re: I need a lighter rifle
« Reply #1 on: October 10, 2023, 12:39:47 PM »
I’m no expert, but my thought is that while the .50 will be lighter than the .40, it may not be lighter than the .54 that is currently too heavy, given that the vast majority of the weight in these rifles is in the barrels. Maybe adding a carry sling to the .54 would be more beneficial.

Jay

Offline bob in the woods

  • Hero Member
  • *****
  • Posts: 4555
Re: I need a lighter rifle
« Reply #2 on: October 10, 2023, 02:42:19 PM »
Get a Kibler Woodsrunner in .54 cal.  I just finished mine, and it's wonderful.
I think it would work for you

Offline J Shingler

  • Full Member
  • ***
  • Posts: 183
Re: I need a lighter rifle
« Reply #3 on: October 10, 2023, 03:09:47 PM »
I have built a rifle with that barrel in 50 cal. I ended up putting a solid brass 3/8" ram rod in it to add weight. With the wood rod it is very light and hard to hold for off hand target shooting. The brass rod adds just enough to help in offhand shooting. With the wood rod it is a great hunting gun. I will go out and weigh it for you when I get home.

As for the build or replacing the barrel in an existing gun, you have a good start with Rice. He is one of the most consistent makers as to outside profile. You could measure the barrel and send him the measurements and see if what he has fits. Then it is just a matter of installing the lugs and tang bolt in the same location. Its a bit of trial and error fitting the tang to an already finished stock but can be done.

Jeff
Thank you
Jeff

Offline smylee grouch

  • Hero Member
  • *****
  • Posts: 7866
Re: I need a lighter rifle
« Reply #4 on: October 10, 2023, 03:21:52 PM »
You could also have the 40 bored out to 45,48 or 50.

Offline recurve

  • Hero Member
  • *****
  • Posts: 616
Re: I need a lighter rifle
« Reply #5 on: October 10, 2023, 03:29:27 PM »


short butterfly poems


I built a Shimmel no brass or steal butt plate b weight swamped B Hoyt barrel about 6 pounds.

you could also talk to Mr.B Hoyt about reboring your 40 to a 50(54)
also look up Herbs older post he cut down a 58 rifle to save weight to elk hunt he's in his 80s
« Last Edit: October 10, 2023, 04:00:08 PM by recurve »

Offline M. E. Pering

  • Sr. Member
  • ****
  • Posts: 273
Re: I need a lighter rifle
« Reply #6 on: October 10, 2023, 03:52:55 PM »
Based on information from Rice on their "B" profile Haines barrel, the change to .50 cal would lighten it by .8 lbs.
« Last Edit: October 11, 2023, 04:15:28 AM by M. E. Pering »

Offline Mike Brooks

  • Hero Member
  • *****
  • Posts: 13415
    • Mike Brooks Gunmaker
Re: I need a lighter rifle
« Reply #7 on: October 10, 2023, 04:15:14 PM »
I'd take a few more weeks to recover from the heart attack and see how things are then.
NEW WEBSITE! www.mikebrooksflintlocks.com
Say, any of you boys smithies? Or, if not smithies per se, were you otherwise trained in the metallurgic arts before straitened circumstances forced you into a life of aimless wanderin'?

Offline Darkhorse

  • Hero Member
  • *****
  • Posts: 1663
Re: I need a lighter rifle
« Reply #8 on: October 10, 2023, 09:11:44 PM »
Mike is right I don't need to rush into this as I've considered several options plus I don't really have time as deer season is upon us.
The 40 barrel will absolutely not be bored out. It's too accurate and does it's job to well to do something like that.
I have a sling that I can easily remove and it helps with carrying the rifles but my problem is shouldering, holding, and trying to maintain some semblance of shooting form.
I am thinking about building a rifle with an "A" 45 caliber barrel. And leave off any excess metal.
Same rifle but with the "B" in 50 caliber.
The shoulders are a real problem now also as I have some kind of deterorating joint disease and both will need replacing. I've dealt with this for several years but now it has progressed to the point of affecting everything I do.
Oh yeah, for all you Kibler pushers out there...I am lefthanded and all my rifles are lefthanded and I'm keeping it that way. So Mr. Kiblers products are out for me.
American horses of Arabian descent.

Offline john bohan

  • Sr. Member
  • ****
  • Posts: 339
Re: I need a lighter rifle
« Reply #9 on: October 10, 2023, 10:37:07 PM »
I am 75 and just finished a 62 cal smooth bore. I was suprized at the accuracy,but it is lighter than any 50 or 54 I own.

Offline bob in the woods

  • Hero Member
  • *****
  • Posts: 4555
Re: I need a lighter rifle
« Reply #10 on: October 11, 2023, 01:53:19 AM »
Mike is right I don't need to rush into this as I've considered several options plus I don't really have time as deer season is upon us.
The 40 barrel will absolutely not be bored out. It's too accurate and does it's job to well to do something like that.
I have a sling that I can easily remove and it helps with carrying the rifles but my problem is shouldering, holding, and trying to maintain some semblance of shooting form.
I am thinking about building a rifle with an "A" 45 caliber barrel. And leave off any excess metal.
Same rifle but with the "B" in 50 caliber.
The shoulders are a real problem now also as I have some kind of deterorating joint disease and both will need replacing. I've dealt with this for several years but now it has progressed to the point of affecting everything I do.
Oh yeah, for all you Kibler pushers out there...I am lefthanded and all my rifles are lefthanded and I'm keeping it that way. So Mr. Kiblers products are out for me.
" Kibler pushers "   :)     I'm not pushing anything,  but was just trying to help. If you had mentioned that you're a lefty [ kind of important ] I wouldn't have suggested it.  You did mention that you cannot really build anything because of your physical troubles, so I'm surprised that you bring up building a .45  with a A weight barrel.  I think Mike B's suggestion is best at this point. 

Offline Darkhorse

  • Hero Member
  • *****
  • Posts: 1663
Re: I need a lighter rifle
« Reply #11 on: October 12, 2023, 01:37:51 AM »
Yes LH is important. I was going to mention it but clean forgot. My bad. No Bob you were not pushing the Kiblers but on some forums  you can't get a discussion going without a ton of posters recommending a Kibler like thiers. Actually I like the way Kibler has put that buisness together, not enough products to choose from though. And no LH products and it seems like none on  the horizon. Important to some of us.
Eventually I will get both shoulders replaced. I can file to my hearts content then and will probably wait till then to build another rifle.
American horses of Arabian descent.

Offline flinchrocket

  • Hero Member
  • *****
  • Posts: 1750
Re: I need a lighter rifle
« Reply #12 on: October 12, 2023, 07:17:24 AM »
I have a Rice Southern Classic in 50 cal. that is light as a feather and built in a barn gun ( no buttplate)
style. I left the wood about 1 3/4 inches wide at the buttstock to lesson the impact of recoil from the light barrel. Very pleasant to shoot and I think something similar would work for you.

Offline Jerry V Lape

  • Hero Member
  • *****
  • Posts: 3028
Re: I need a lighter rifle
« Reply #13 on: October 12, 2023, 09:29:54 AM »
Maybe someone has a Jaeger style rifle with a short barrel.  Some of those were built with 28 inch barrels.  The one of those I have handled have felt nice and light.  Removing 10 inches or so of barrel significantly reduces weight.

Offline alacran

  • Hero Member
  • *****
  • Posts: 2237
Re: I need a lighter rifle
« Reply #14 on: October 12, 2023, 01:05:15 PM »
The photo clearly shows a left-handed rifle. To me it looks to be a 42-inch barrel I built a 38-inch Rice barreled rifle in .50 and it came in at 7.5 lbs. So if you rebarrel yours it will be closer to 8 pounds.
A man's rights rest in three boxes: the ballot box, the jury box, and the cartridge box.  Frederick Douglass

Offline Steeltrap

  • Hero Member
  • *****
  • Posts: 750
Re: I need a lighter rifle
« Reply #15 on: October 12, 2023, 03:43:39 PM »
Can you just pick up an inexpensive Frankenrifle and cut maybe 10" off the barrel?  If you're just going to hunt with it I doubt the deer will notice.

Offline Bob Gerard

  • Hero Member
  • *****
  • Posts: 1307
    • Powder Horns and Such
Re: I need a lighter rifle
« Reply #16 on: October 12, 2023, 03:49:17 PM »
A Smoothbore would certainly be one option to consider. Much lighter and can do the job of a rifle (and sometimes more) out to 50 yards or better.

Offline mark esterly

  • Sr. Member
  • ****
  • Posts: 408
Re: I need a lighter rifle
« Reply #17 on: October 12, 2023, 06:33:22 PM »
crazy question maybe but have you tried adding weight to the butt (up to 8oz. maybe) to shift the balance. maybe it's not the weight but where the weight is with your limitations now?
living in the hope of HIS coming.......

Offline smokinbuck

  • Hero Member
  • *****
  • Posts: 3002
Re: I need a lighter rifle
« Reply #18 on: October 13, 2023, 05:46:13 PM »
Darkhorse,
I have several LH rifles that are lighter than what you have in both .50 & .54 but they are cap locks. If you are interested I can send pics.
Mark

Offline hanshi

  • Hero Member
  • *****
  • Posts: 5328
  • My passion is longrifles!
    • martialartsusa.com
Re: I need a lighter rifle
« Reply #19 on: October 13, 2023, 09:01:12 PM »
At 77 I no longer hunt, I just kill paper.  Mentioned in another post is my 7 lb .45 X 36" X 13/16" barrel I used to hunt with.  I also have a delightful full stock flintlock 38" X "B" wgt X .50 that only goes 7 lbs 2 oz.  The barrel is a Rice with radius groove rifling.  Both the .45 and the .50 are sweet handling, light weight and supremely accurate.  I'd think a .50 barrel of the same profile as your .40 would save at least 8 oz.
!Jozai Senjo! "always present on the battlefield"
Young guys should hang out with old guys; old guys know stuff.

Offline thecapgunkid

  • Hero Member
  • *****
  • Posts: 1104
  • Matthew 25:40
Re: I need a lighter rifle
« Reply #20 on: October 14, 2023, 04:57:03 PM »
Dark, I hate to admit it but this same issue set has plagued me for about five years....surgery a year and a half ago for the heart and bone/joint issues through it.

The only thing I was able to do was build whatever I was going to use at seven pounds or under.  That involved saying bye-bye to one of my favorite guns, going with shorter barrels and Jaeger barrels in .58 caliber.

The arm movement issues you describe are enough of a show stopper in themselves, and you're right about cutting into your build efforts.  I did cut one gun down and spent a ton of time on the muzzle making sure it was right, but I had to sight it in all over again.  I've also had to take the hunting pouch off my shoulder and put it on the belt.

Godspeed and feel better.

Capgun


Offline B.Habermehl

  • Hero Member
  • *****
  • Posts: 1685
Re: I need a lighter rifle
« Reply #21 on: October 14, 2023, 06:41:15 PM »
The “b” .50 would probably save you the best part of a pound out front. The minor down side will be fitting. Installing the lugs in the same locations and drilling. Plus fitting the breech, tangbolt etc. this can be a pain but doable. Been there and done that. Carefull spot drilling on the lugs and finish drilling out of the stock will help with preventing oversized pin holes in the stock. Plus of course, touch hole placement. BJH
BJH

Offline oldtravler61

  • Hero Member
  • *****
  • Posts: 4402
  • We all make mistakes.
Re: I need a lighter rifle
« Reply #22 on: October 14, 2023, 09:03:43 PM »
  Interesting I too have shoulder and neck injuries. But what I did was buy one of those shooting sticks when I'm hunting. Their quick to use, handy as a walking stick and really helps steady your aim.  Just a thought and  cheaper than a new gun.

Offline Darkhorse

  • Hero Member
  • *****
  • Posts: 1663
Re: I need a lighter rifle
« Reply #23 on: October 14, 2023, 10:43:57 PM »
I've been using a shooting stick. I also have a tripod I use in blinds. A couple even have sandbags. All of these make hunting possible. Getting the rifle on the shooting aid can be a problem though. A quick offhand shot is not going to happen.
If I actually get to hunt this year (land problem) I think I'll buy a new, easily adjustable and lighter tripod, they just work so good.
American horses of Arabian descent.

Offline Daryl

  • Hero Member
  • *****
  • Posts: 15662
Re: I need a lighter rifle
« Reply #24 on: October 15, 2023, 12:13:27 AM »
Or a more comfortable blind? This one is fully insulated, has a propane heater and a camo drop cloth to cover the entrance.
While sitting there, I had a black bear stand up in front and look down the muzzle of my .69. It's 104 yards to the bush line
out in front. 125yds to the left hand corner.
Did I mention it is planted in oats?









« Last Edit: October 15, 2023, 12:17:11 AM by Daryl »
Daryl

"a gun without hammers is like a spaniel without ears" King George V